2011-2013 Land Cruiser · Service Manual Vehicle Interior

TERMINALS OF ECU

System information · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
C172609E06
  1. Disconnect the 2A, 2D and E3 ECU connectors.

  2. Measure the resistance and voltage according to value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    2A-1 (ACC) - 2D-62 (GND2)
    B - W-B
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    2A-1 (IG) - 2D-62 (GND2)
    B - W-B
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the 2A, 2D and E3 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E1-24 (DCTY) - Body ground
    L - Body ground*1
    Y - Body ground*2
    Driver side door courtesy light switch input
    Driver side door open
    Below 1 Ω
    Driver side door closed
    10 kΩ or higher
    E2-21 (PCTY) - Body ground
    Y - Body ground*1
    L - Body ground*2
    Passenger side door courtesy light switch input
    Passenger side door open
    Below 1 Ω
    Passenger side door closed
    10 kΩ or higher
    2C-2 (LCTY) - Body ground
    W - Body ground
    Rear side door LH courtesy light switch input
    Rear side door LH open
    Below 1 Ω
    Rear side door LH closed
    10 kΩ or higher
    E2-7 (RCTY) - Body ground
    G - Body ground
    Rear side door RH courtesy light switch input
    Rear side door RH open
    Below 1 Ω
    Rear side door RH closed
    10 kΩ or higher
    E2-25 (BCTY) - Body ground
    w - Body ground
    Back door courtesy light switch input
    Back door open
    Below 1 Ω
    Back door closed
    10 kΩ or higher
    E3-7 (HZSW) - Body ground
    BE - Body ground
    Turn signal light drive
    Hazard warning signal switch on
    Pulse generation
    Hazard warning signal switch off
    Below 1 V
    2B-16 (DIM) - 2D-62 (GND2)*
    R-G - W-B
    Headlight low drive
    Headlight dimmer switch low
    11 to 14 V
    2B-18 (HRLY) - 2D-62 (GND2)*
    L - W-B
    Headlight (high) drive
    Headlight dimmer switch high
    11 to 14 V
    2A-1 (TRLY) - 2D-62 (GND2)*
    B - W-B
    Taillight drive
    Headlight dimmer switch tail
    11 to 14 V
    1. *1: for LHD
    2. *2: for RHD

    HINT:
    *: w/ Panic Switch

    If the result is not as specified, the ECU may have a malfunction.

  5. B122376E01
    Using an oscilloscope, check waveform 1.
    Waveform 1 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-24 (DCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and driver side door courtesy switch off

  6. B129408E01
    Using an oscilloscope, check waveform 2.
    Waveform 2 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E1-24 (DCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and driver side door courtesy switch off

  7. B189909E01
    Using an oscilloscope, check waveform 3.
    Waveform 3 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-21 (PCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and passenger side door courtesy switch off

  8. B189910E01
    Using an oscilloscope, check waveform 4.
    Waveform 4 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-21 (PCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and passenger side door courtesy switch off

  9. B122376E01
    Using an oscilloscope, check waveform 5.
    Waveform 5 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-2 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear LH side door courtesy switch off

  10. B129408E01
    Using an oscilloscope, check waveform 6.
    Waveform 6 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    2C-2 (LCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear LH side door courtesy switch off

  11. B122376E01
    Using an oscilloscope, check waveform 7.
    Waveform 7 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-7 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear RH side door courtesy switch off

  12. B129408E01
    Using an oscilloscope, check waveform 8.
    Waveform 8 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-7 (RCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and rear RH side door courtesy switch off

  13. B122376E01
    Using an oscilloscope, check waveform 9.
    Waveform 9 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-25 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and Back door closed

  14. B129408E01
    Using an oscilloscope, check waveform 10.
    Waveform 10 (Reference) 
    Item
    Content
    Terminal No. (Symbol)
    E2-25 (BCTY) - Body ground
    Tool Setting
    5 V/DIV., 20 ms/DIV.
    Condition
    Engine switch off, and Back door closed


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
B106648E46
  1. Disconnect the E29 and E30 ECU connectors.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E29-17 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E29-1 (+B1) - E29-17 (E)
    B - W-B
    Battery power supply
    Always
    11 to 14 V
    E29-18 (IG) - E29-17 (E)
    B - W-B
    IG power supply
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E29 and E30 ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E29-39 (RSSI) - E29-17 (E)
    L - W-B
    Door control receiver electric wave existence signal
    Engine switch off, all doors closed and transmitter switch not pressed → pressed
    11 to 14 V → Below 1 V
    E29-38 (RDA) - E29-17 (E)
    LG - W-B
    Door control receiver data input signal
    Engine switch off, all doors closed and transmitter switch not pressed → pressed
    Below 1 V → 11 to 14 V → Below 1 V
    E29-29 (RCO) - E29-17 (E)
    B - W-B
    Door control receiver power source
    Engine switch off, all doors closed and transmitter switch not pressed → pressed
    Below 1 V → 4.6 to 5.4 V → Below 1 V
    E29-21 (BZR) - Body ground*
    LG - Body ground
    Wireless door lock buzzer output
    Wireless door lock buzzer ON
    11 to 14 V
    E29-21 (BZR) - Body ground*
    LG - Body ground
    Wireless door lock buzzer output
    Wireless door lock buzzer OFF
    Below 1 V

    HINT:
    *: Except Europe and China

    1. If the result is not as specified, the ECU may have a malfunction.


CHECK DOOR CONTROL RECEIVER
E159309E01
  1. Disconnect the L21 receiver connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L21-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L21-4 (+5) - Body ground
    B - Body ground
    Battery power supply
    Always
    4.6 to 5.4 V
    1. If the result is not as specified, there may be a malfunction on the wire harness side.


CHECK POWER BACK DOOR UNIT (w/ Power Back Door System)
H100802E30
  1. Disconnect the L52 unit connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L52-11 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    L52-10 (ECUB) - Body ground
    R - Body ground
    Battery power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the L52 unit connector.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    L52-26 (BZR+) - Body ground
    L - Body ground
    Power back door warning buzzer signal
    Back door warning buzzer is sounding
    11 to 14 V
    Pulse generation
    L52-26 (BZR+) - Body ground
    L - Body ground
    Power back door warning buzzer signal
    Back door warning buzzer is stopped
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.

← TERMINALS OF ECU (Sep 2011 – Dec 2011)DTC CHECK / CLEAR (from Sep 2011) →