DATA LIST / ACTIVE TEST
System information · Vehicles built from Sep 2011
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Data List.
Check the values by referring to the table below.
Tilt & Telescopic Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Tilt Position
Current tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Position
Current telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Return Position
Memorized tilt return position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Return Position
Memorized telescopic return position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Memory Pos 1
Tilt data of memory position 1/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Memory Pos 1
Telescopic data of memory position 1/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Memory Pos 2
Tilt data of memory position 2/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Memory Pos 2
Telescopic data of memory position 2/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Memory Pos 3
Tilt data of memory position 3/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Memory Pos 3
Telescopic data of memory position 3/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Up Limit
Uppermost tilt position/Not Mem or Mem
Not Mem: Position not memorized
Mem: Position memorized
-
Tilt Up Limit Position
Uppermost tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Down Limit
Lowermost tilt position/Not Mem or Mem
Not Mem: Position not memorized
Mem: Position memorized
-
Tilt Down Limit Position
Lowermost tilt position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Short Limit
Shortest telescopic position/Not Mem or Mem
Not Mem: Position not memorized
Mem: Position memorized
-
Telesco Short Limit Pos
Shortest telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Telesco Long Limit
Longest telescopic position/Not Mem or Mem
Not Mem: Position not memorized
Mem: Position memorized
-
Telesco Long Limit Pos
Longest telescopic position data/min.: 0000 H (0 edges), max.: FFFF H (65535 edges)
7000 to 9000 H
(28672 to 36864 edges)
-
Tilt Up Switch
Input state of tilt up by manual switch/ON or OFF
ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch
-
Tilt Up SW (CAN)
Input state of tilt up by manual switch/ON or OFF
ON: Tilt up activated by manual switch
OFF: Tilt up not activated by manual switch
-
Tilt Down Switch
Input state of tilt down by manual switch/ON or OFF
ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch
-
Tilt Down SW (CAN)
Input state of tilt down by manual switch/ON or OFF
ON: Tilt down activated by manual switch
OFF: Tilt down not activated by manual switch
-
Telesco Short Switch
Input state of telescopic short by manual switch/ON or OFF
ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch
-
Telesco Short SW (CAN)
Input state of telescopic short by manual switch/ON or OFF
ON: Telescopic short activated by manual switch
OFF: Telescopic short not activated by manual switch
-
Telesco Long Switch
Input state of telescopic long by manual switch/ON or OFF
ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch
-
Telesco Long SW (CAN)
Input state of telescopic long by manual switch/ON or OFF
ON: Telescopic long activated by manual switch
OFF: Telescopic long not activated by manual switch
-
T&T Manual SW Data
Voltage data of manual switch/min.: 0 V, max.: 5 V
Neutral position: Below 0.2 V
Tilt up: 1.67 to 2.13 V
Tilt down: 0.54 to 0.74 V
Telescopic contract: 1.08 to 1.40 V
Telescopic extend: 2.22 to 2.77 V
-
S/B Mem 1
Tilt and telescopic memory position 1/Not Mem or Mem
Not Mem: Position not memorized
Mem: Position memorized
-
S/B Mem 2
Tilt and telescopic memory position 2/Not Mem or Mem
Not Mem: Position not memorized
Mem: Position memorized
-
S/B Mem 3
Tilt and telescopic memory position 3/Not Mem or Mem
Not Mem: Position not memorized
Mem: Position memorized
-
T&T Autoaway Function
Auto away/return function/ON or OFF
ON: Auto away/return function allowed
OFF: Auto away/return function prohibited
-
Power Source Voltage
Voltage data of power supply/min.: 0 V, max.: 20 V
Actual power supply voltage
11 to 14 V
-
Freeze Speed Info
Vehicle speed data/min.: 0 km/h (0 mph), max.: 255 km/h (158 mph)
Actual vehicle speed
-
IG Switch (CAN)
Communication state of engine switch/ON or OFF
ON: Communication normal
OFF: Communication interrupted
-
IG Switch
Input state of engine switch/ON or OFF
ON: Input signal normal
OFF: Input signal interrupted
-
Key Code Confirm (CAN)
Communication state of key code confirmation signal/ON or OFF
ON: Communication normal
OFF: Communication interrupted
-
Receive from Meter
Communication state of combination meter signal/OK or Interruption
OK: Communication normal
Interruption: Communication interrupted
-
Receive from Seat ECU
Communication state of position control ECU signal/OK or Interruption
OK: Communication normal
Interruption: Communication interrupted
-
Receive from Combi
Communication state of combination switch ECU signal/OK or Interruption
OK: Communication normal
Interruption: Communication interrupted
-
J/B
Communication state of main body ECU signal/OK or Interruption
OK: Communication normal
Interruption: Communication interrupted
-
B/B
Communication state of optional after parts ECU signal/OK or Interruption
OK: Communication normal
Interruption: Communication interrupted
-
Driver Seat Buckle SW
Driver side buckle switch signal / Set, Unset or Unknown
-
-
The Number of DTCs
Number of diagnostic trouble codes/min.: 0, max.: 255
Actual number of diagnostic trouble codes
-
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Test allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Test early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Test.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body Electrical / Tilt & Telescopic / Active Test.
Check the values by referring to the table below.
Tilt & Telescopic Tester Display
Test Part
Control Range
Diagnostic Note
Tilt Operation
Tilt operation
Up/Down
-
Telesco Operation
Telescopic operation
Long/Short
-