2011-2013 Land Cruiser · Service Manual Drivetrain

Pattern Select Switch 2nd Start Mode Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

When 2nd mode is selected with the pattern select (2ND) switch, the ECM controls the solenoid valves and the transmission starts from 2nd gear.
The 2nd mode is the system that operates the throttle motor to control engine output to reduce skidding of the driving wheels, and guarantee takeoff acceleration, driving straightness and turning stability.
When the shift lever is in D, the transmission automatically shifts up through 3rd to 5th as usual.

WIRING DIAGRAM

Refer to Pattern Select Switch Power Mode Circuit (Click here).

INSPECTION PROCEDURE

When the pattern select (2ND) switch is pushed, switch contact is made and 2nd mode is selected. To cancel 2nd mode, push the pattern select (2ND) switch once again.

HINT:
2nd mode is automatically canceled when the engine switch is turned off.


1. DRIVING TEST

HINT:
The driving test should be performed on a paved road (nonskid road).

  1. Start the engine.

  1. Turn the 2ND switch off (normal drive mode).

  1. Confirm vehicle response by driving from a parked position to fully depressing the accelerator pedal.

  1. Turn the 2ND switch on and perform the same check as above.When driving the vehicle with the 2ND switch on and off, check that there is a difference in acceleration.

    OK:
    There is a difference in acceleration.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT PATTERN SELECT (2ND) SWITCH

  1. C175598E19
    Remove the suspension control switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    17 (2ND) - 20 (E)
    Pattern select (2ND) switch continuously pressed
    Below 1 Ω
    17 (2ND) - 20 (E)
    Pattern select (2ND) switch released
    10 kΩ or higher



NG
REPLACE PATTERN SELECT (2ND) SWITCH (SUSPENSION CONTROL SWITCH) (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - BODY GROUND)

  1. C176957E01
    Disconnect the V4 suspension control switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    V4-20 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (PATTERN SELECT (2ND) SWITCH - ECM)
C177782E07
  1. Disconnect the A38 ECM connector (for LHD).

  1. Disconnect the A52 ECM connector (for RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    A38-4 (SNWI) - Body ground
    Pattern select (2ND) switch continuously pressed
    Below 1 Ω
    A38-4 (SNWI) - Body ground
    Pattern select (2ND) switch released
    10 kΩ or higher
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    A52-4 (SNWI) - Body ground
    Pattern select (2ND) switch continuously pressed
    Below 1 Ω
    A52-4 (SNWI) - Body ground
    Pattern select (2ND) switch released
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)


← Pattern Select Switch Power Mode Circuit (Sep 2011 – Dec 2011)L4 Position Switch Circuit (Sep 2011 – Dec 2011) →