2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built Sep 2011 – Dec 2011


NAVIGATION SYSTEM OUTLINE

  1. Vehicle position tracking methods
    It is essential that the navigation system correctly tracks the current vehicle position and displays it on the map. There are 2 methods to track the current vehicle position; autonomous (dead reckoning) and GPS* (satellite) navigation. Both navigation methods are used in conjunction with each other.
    *GPS (Global Positioning System)
    E187243E01

    Operation
    Description
    Vehicle Position Calculation
    The display and navigation module display calculates the current vehicle position (direction and current position) using the direction deviation signal from the gyro sensor and the running distance signal from the vehicle speed sensor and creates the driving route.
    Map Display Processing
    The display and navigation module display displays the vehicle track on the map by processing the vehicle position data, vehicle running track and map data from the map disc.
    Map Matching
    The map data from the map disc is compared to the vehicle position and running track data. Then, the vehicle position is matched with the nearest road.
    GPS Correction
    The vehicle position is matched to the position measured by GPS. Then, the GPS measurement position data is compared with the vehicle position and running track data. If the position is widely different, the GPS measurement position is used.
    Distance Correction
    The vehicle speed signal includes the error caused by tire wear and slippage between the tires and road surface. Distance correction is performed to account for this. The display and navigation module display automatically offsets the signal to make up for the difference between it and the distance data of the map. The offset is automatically updated.
    I100028E27

    HINT:
    The combination of autonomous and GPS navigation makes it possible to display the vehicle position even when the vehicle is in places where the GPS cannot receive a signal. When only autonomous navigation is used, however, the mapping accuracy may slightly decrease.

  2. Autonomous navigation
    This method determines the relative vehicle position based on the running track determined by the gyro located in the display and navigation module display and the vehicle speed sensor's signal.

    1. Gyro sensor
      Used to calculate the direction by detecting angular velocity. It is located in the display and navigation module display.

    2. Vehicle speed sensor signal
      Used to calculate the vehicle running distance.

  3. GPS* navigation (Satellite navigation)
    This method detects the absolute vehicle position using radio waves from GPS satellites.
    *GPS satellites were launched by the U.S. Department of Defense for military purposes.
    I100029E07

    Number of Satellites
    Measurement
    Description
    2 or less
    Measurement impossible
    Vehicle position cannot be obtained because the number of satellites is not enough.
    3
    2-dimensional measurement is possible
    Vehicle position is obtained based on the current longitude and latitude. (This is less precise than 3-dimensional measurement.)
    4
    3-dimensional measurement is possible
    Vehicle position is obtained based on the current longitude, latitude and altitude.

  4. Map matching
    The current driving route is calculated by autonomous navigation (according to the gyro sensor and vehicle speed sensor) and GPS navigation. This information is then compared with possible road shapes from the map data in the map disc and the vehicle position is set onto the most appropriate road.
    I100030E19

  5. Touch switch
    Touch switches are touch-sensitive (interactive) switches operated by touching the screen. When a switch is pressed, the outer glass bends to contact the inner glass at the pressed position. By doing this, the voltage ratio is measured and the pressed position is detected.
    I100031E10


DVD (Digital Versatile Disc) PLAYER OUTLINE (Navigation Map)
  1. The navigation module board uses a laser pickup to read the digital signals recorded on a DVD.

    CAUTION:
    Because the navigation system uses an invisible laser beam, do not look directly at the laser pickup. Be sure to only operate the navigation system as instructed.

    NOTICE:
    1. Do not disassemble any part of the navigation module board.
    2. Do not apply oil to the navigation module board.
    3. Do not insert anything but a DVD into the navigation module board.


DVD (Digital Versatile Disc) PLAYER OUTLINE (DVD Changer)

  1. The DVD player can only play DVD videos, DVD audio and video CDs that have any of the following marks:
    E183980

    1. Precaution for use of discs

      NOTICE:
      1. PAL or SECAM color television standard discs cannot be played (only NTSC discs can be played).
      2. Keep the discs away from dirt. Be careful not to damage the discs or leave fingerprints on them.
      3. Hold discs by the outer edge and center hole with the label side up.
      4. Leaving the disc exposed halfway out of the slot for a long time after pressing the disc eject button may cause deformation of the disc, making the disc unusable.
      5. Do not use odd-shaped CDs because these may cause player malfunctions.
      6. Do not use discs whose recording portion is transparent or translucent because they may not be inserted, ejected or played normally.
      7. DualDiscs that combine DVD recorded material on one side with CD digital audio material on the other cannot be played.

  2. Cleaning

    NOTICE:
    Do not use a lens cleaner because it may cause a malfunction in the pickup portion of the player.


    1. I100151
      If dirt is on the disc surface, wipe it clean with a soft dry cloth such as an eyeglass cleaner for plastic lenses from the inside to the outside in a radial direction.

      NOTICE:
      1. Pressing on the disc by hand or rubbing the disc with a hard cloth may scratch the disc surface.
      2. Use of solvent such as a record spray, antistatic agent, alcohol, benzine and thinner or a chemical cloth may cause damage to the disc, making the disc unusable.


CD (Compact Disc) PLAYER OUTLINE
  1. A compact disc player uses a laser pickup to read digital signals recorded on a compact disc (CD). By converting the digital signals to analog, it can play music and audio.

    CAUTION:
    Do not look directly at the laser pickup because the CD player uses an invisible laser beam. Be sure to operate the player only as instructed.

    NOTICE:
    1. Do not disassemble any part of the CD player.
    2. Do not apply oil to the CD player.
    3. Do not insert anything but a CD into the CD player.

  2. Usable discs

    1. This player can play only audio CDs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) that have any of the following marks:
      E119759

  3. Precautions for use of discs

    NOTICE:
    1. Copy-protected CDs cannot be played.
    2. CD-Rs and CD-RWs may not be played depending on the recording conditions or characteristics of the discs, or due to damage, dirt or deterioration caused by leaving the discs in the cabin for a long time.
    3. Unfinalized CD-Rs and CD-RWs cannot be played.
    4. DualDiscs that combine DVD recorded material on one side with CD digital audio material on the other cannot be played.
    5. Keep the discs away from dirt. Be careful not to damage the discs or leave your fingerprints on them.
    6. Hold discs by the outer edge and center hole with the label side up.
    7. Leaving the disc exposed halfway out of the slot for a long time after pressing the disc eject button may cause deformation of the disc, making the disc unusable.
    8. If discs have adhesive tape, stickers, CD labels or any traces of such attached, the discs may not be ejected or player malfunctions may result.
    9. Keep the discs away from direct sunlight. (Exposure to direct sunlight may cause deformation of the disc, making the disc unusable.)
    10. Do not use odd-shaped CDs because these may cause player malfunctions.
    11. Do not use discs whose recording portion is transparent or translucent because they may not be inserted, ejected or played normally.

    HINT:
    1. When it is cold or it is raining, if the windows mist up, mist and condensation may form in the player. In such cases, the CD sound may skip or stop in the middle of play. Ventilate or dehumidify the cabin for a while before using the player.
    2. The CD sound may skip if the player experiences strong vibrations when the vehicle is driven on rough roads or similar uneven surface(s).

  4. Cleaning

    NOTICE:
    Do not use a lens cleaner because it may cause a malfunction in the pickup portion of the player.


    1. I100151
      If dirt is on the disc surface, wipe it clean with a soft dry cloth such as an eyeglass cleaner for plastic lenses from the inside to the outside in a radial direction.

      NOTICE:
      1. Pressing on the disc by hand or rubbing the disc with a hard cloth may scratch the disc surface.
      2. Use of solvent such as a record spray, antistatic agent, alcohol, benzine and thinner or a chemical cloth may cause damage to the disc, making the disc unusable.


MP3/WMA OUTLINE
  1. Playable MP3 file standards

    Compatible standard
    MP3 (MPEG1 LAYER 3, MPEG2 LSF LAYER 3)
    Compatible sampling frequency
    1. MPEG1 LAYER 3: 32, 44.1, 48 (kHz)
    2. MPEG2 LSF LAYER 3: 16, 22.05, 24 (kHz)
    Compatible bit rate
    1. MPEG1 LAYER 3: 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps)
    2. MPEG2 LSF LAYER 3: 64, 80, 96, 112, 128, 144, 160 (kbps)
    3. Compatible with VBR
    Compatible channel mode
    Stereo, joint stereo, dual channel, monaural

  2. Playable WMA file standards

    Compatible standard
    WMA Ver. 7, 8, and 9
    Compatible sampling frequency
    32, 44.1, 48 (kHz)
    Compatible bit rate (Only compatible with 2-channel playback)
    1. Ver. 7, 8: CBR48, 64, 80, 96, 128, 160, 192 (kbps)
    2. Ver. 9: CBR48, 64, 80, 96, 128, 160, 192, 256, 320 (kbps)

  3. ID3 tag and WMA tag

    1. Additional textual information called ID3 tag can be input to MP3 files. Information such as song titles and artist names can be stored.

      HINT:
      This player is compatible with the ID3 tags of ID3 Ver. 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3. (Number of characters complies with ID3 Ver. 1.0 and 1.1.)

    2. Additional textual information called WMA tag can be input to WMA files. Information such as song titles and artist names can be stored.

  4. Usable media

    1. Only CD-ROMs, CD-Rs (CD-Recordable) and CD-RWs (CD-ReWritable) can be used to play MP3/WMA files.

      NOTICE:
      1. CD-Rs and CD-RWs are more easily affected by a hot and humid environment than discs used for normal audio CDs. For this reason, some CD-Rs and CD-RWs will not play.
      2. If there are fingerprints or scratches on a disc, the disc may not play or the CD sound may skip.
      3. Some CD-Rs and CD-RWs may deteriorate if they are left in the cabin for a long time.
      4. Keep CD-Rs and CD-RWs in an opaque case.

  5. Usable media format

    1. Usable media format

      Disc format
      CD-ROM Mode 1, CD-ROM XA Mode 2 Form 1
      File format
      ISO9660 Level 1 and Level 2 (Joliet, Romeo)

      HINT:
      1. As for MP3/WMA files written in any unlisted format, the contents of the files may not be played normally or the file names or folder names may not be displayed correctly.
      2. This player is compatible with multi-session discs and can play CD-Rs and CD-RWs on which MP3/WMA files are added. However, only the first session can be played.
      3. Discs whose first session includes both music data and MP3 or WMA format data cannot be played.

    2. Standard and restrictions

      Maximum directory levels
      8 levels
      Maximum number of characters for a folder name/file name
      32 characters
      Maximum number of folders
      192 (Including empty folders, root folders, and folders that do not contain MP3/WMA files)
      Maximum number of files in a disc
      255 (Including non-MP3/WMA files)

  6. File names

    1. Only files with an extension of ".mp3" or ".wma" can be recognized and played as MP3 or WMA files.

    2. Save MP3 or WMA files with an extension of ".mp3" or ".wma".

      NOTICE:
      If non-MP3 or non-WMA files are saved with an extension of ".mp3" or ".wma", those files may be wrongly recognized as MP3 or WMA files and played. A loud noise may occur and damage to the speakers may result.


"Bluetooth" OUTLINE
  1. "Bluetooth" is a trademark owned by Bluetooth SIG. Inc.

  2. "Bluetooth" is a new wireless connection technology that uses the 2.4 GHz frequency band.

    HINT:
    The communication performance of "Bluetooth" may vary depending on obstructions or radio wave conditions between communication devices, electromagnetic radiation, communication device sensitivity or antenna capacity.

  3. Hands-free function

    1. The "Bluetooth" built-in radio receiver and a "Bluetooth" compatible cellular phone*1 can be connected using a "Bluetooth" wireless connection. This enables use of the hands-free function on the cellular phone even though the phone may be in a pocket or bag. For this reason, it is not necessary to use a connector or cable to connect the cellular phone.
      *1: Some versions of "Bluetooth" compatible cellular phones may not function.
      E194851E01

      Text in Illustration 
      *1
      Radio Receiver Assembly
      (Built-in "Bluetooth" Receiver Antenna)
      *2
      Cellular Phone
      ("Bluetooth" Type)
      *3
      Cellular Tower
      -
      -


VEHICLE CUSTOMIZATION OUTLINE
  1. Customization of functions can be performed on the multi display screen. Refer to the owner's manual for further information on customizable items for the navigation system.

    HINT:
    1. Items available for customization via the navigation system can be performed by using the intelligent tester.
    2. Some customize parameters displayed on the intelligent tester will be displayed on the "Vehicle Customization" screen for the navigation system. Users can customize these items.


COMMUNICATION SYSTEM

  1. MOST Network Outline
    E192455E03

    1. Navigation system components communicate with each other via the MOST network.

    2. The MOST network uses a shielded twisted pair of wires for its communication lines.

    3. The master unit of the MOST network is the display and navigation module display (navigation ECU).

    4. MOST communication lines connect each slave unit centering around the master unit to form a MOST network ring.

    5. The master unit sends a wake-up signal to activate each slave unit connected to the MOST network.

      HINT:
      If a short or open circuit occurs in the MOST circuit, communication will be interrupted and the system will not operate normally.

  2. AVC-LAN Outline
    E194852E01

    1. Components of the navigation system communicate with each other via the AVC-LAN.

    2. The AVC-LAN uses a twisted pair of wires for its communication lines.

    3. The master unit of the AVC-LAN is the display and navigation module display (navigation ECU).

      HINT:
      1. The display and navigation module display (navigation ECU) has enough resistance (60 to 80 Ω) necessary for communication.
      2. If a short or open circuit occurs in the AVC-LAN circuit, communication is interrupted and the system will not operate normally.


DIAGNOSTIC FUNCTION OUTLINE
  1. The navigation system has a diagnostic function (the result will be displayed on the master unit or the intelligent tester).


DIAGNOSIS DISPLAY DETAILED DESCRIPTION

HINT:
  1. This section contains a detailed description of displays in diagnostic mode.
  2. Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.

  1. Service Menu Screen
    E176504

    HINT:
    Each item is grayed out or not displayed based on the device settings.

  2. Failure Diagnosis Screen
    E176575

    HINT:
    Each item is grayed out or not displayed based on the device settings.


    1. System Check Mode Screen
      E196410E01

      1. *1: Node position number for devices connected to the MOST network.

        HINT:
        MOST node position numbers are provided for devices connected to the MOST network.

      2. *2: Device Name List No. 1

        HINT:
        1. Device Name List No. 1 displays some of the devices that make up the navigation system.
        2. The names of the components from Device Name List No. 1 are shown in the following table.
          Name
          Component
          Connection Method
          EMVN
          Display and navigation module display
          -
          AUDIO
          Radio receiver assembly
          Communication line for MOST network
          AMP
          Stereo component amplifier assembly
          Communication line for MOST network
          RSE
          Television display assembly
          Communication line for MOST network
          CAMERA-C
          Parking assist ECU
          Communication line for AVC-LAN
          USB BOX
          Multi-media interface ECU
          Communication line for AVC-LAN

      1. *3: Check Result

        HINT:
        1. Result codes for all devices are displayed.
        2. When "MOST" is displayed for the result, press "MODE" on the steering pad switch assembly to display the "MOST Line Check" screen.
        Result
        Meaning
        Action
        OK
        The device does not respond with a DTC.
        -
        MOST
        MOST communication error
        Perform "MOST Line Check" to check the connection of each device on the MOST network.
        EXCH
        The device responds with a "replace"-type DTC.
        Look up the DTC in "Unit Check Mode" and replace the device.
        CHEK
        The device responds with a "check"-type DTC.
        Look up the DTC in "Unit Check Mode".
        NCON
        The device was previously present, but does not respond in diagnostic mode.
        - Check power supply wire harness of the device.
        - Check the AVC-LAN or MOST network for the device.
        NRES
        The device responds in diagnostic mode, but gives no DTC information.
        - Check power supply wire harness of the device.
        - Check the AVC-LAN or MOST network for the device.

      1. *4: Memory Clear

        HINT:
        1. Present and history DTCs and registered connected device names are cleared.
        2. Press the "Memory CLR" switch for 3 seconds.

      1. *5: Recheck

        HINT:
        1. A system check will be performed again after the memory is cleared.
        2. The "Recheck" switch will dim during a system check.

      1. *6: Device Name List No. 2

        HINT:
        1. Device Name List No. 2 displays some of the devices that make up the navigation system.
        2. The names of the components from Device Name List No. 2 are shown in the following table.
          Name
          Component
          Connection Method
          MIC
          Telephone microphone assembly
          Vehicle wire harness
          AUX
          Stereo jack adapter assembly
          Vehicle wire harness
          VTR
          Video (video adapter) terminal
          Vehicle wire harness

    2. Unit Check Mode Screen
      E199105E01

      Screen Description 
      Display
      Content
      *1: Device name
      Target device
      *2: History DTC
      Diagnostic memory results and stored DTCs are displayed.
      *3: Present DTC
      DTCs output in the service check are displayed.
      *4: DTC
      DTC (Diagnostic Trouble Code)
      *5: Timestamp
      The time and date of history DTCs are displayed. (The year is displayed in 2-digit format.)
      *6: Diagnosis clear switch
      Pushing this switch for 3 seconds clears the diagnostic memory data of the target device. (Both response to diagnostic system check result and the displayed data are cleared.)

    3. MOST Line Check Screen

      HINT:
      1. The inspection will be performed at the time the screen changes from "System Check Mode" to "MOST Line Check".
      2. The master unit checks the connection of each device on the MOST network.

      E194854E01
      1. *1: Node position number for devices connected to the MOST network.
      2. *2: Device Name List

        HINT:
        1. Device Name List displays some of the devices that make up the navigation system.
        2. The names of the components from Device Name List are shown in the following table.
          Name
          Component
          EMVN
          Display and navigation module display
          AUDIO
          Radio receiver assembly
          AMP
          Stereo component amplifier assembly
          RSE
          Television display assembly

      1. *3: Check Result

        HINT:
        1. The master unit displays the check result on the screen based on the response information from each slave unit.
        2. Result codes for all devices are displayed.
          Result
          Meaning
          OK
          There was a response for the connection check during the MOST line check.
          NCON
          There was no response for the connection check during the MOST line check.
        3. The device name and result will not be displayed if there is no system registration record and no response for the connection check during the MOST line check even if the device is connected to the MOST network.

  3. Function Check/Setting Screen
    E196411

    HINT:
    Each item is grayed out or not displayed based on the device settings.


    1. Microphone & Voice Recognition Check Screen
      E176507E01

      Screen Description 
      Display
      Content
      *1: Microphone input level meter
      Monitors the microphone input level every 0.1 sec. and displays the results in 8 different levels.
      *2: Recording switch
      Starts recording.
      *3: Stop switch
      Stops recording and playing.
      *4: Play switch
      Plays the recorded voice.
      *5: Recording indicator
      Comes on while recording.

      HINT:
      1. The microphone is active at all times when this screen is displayed.
      2. While recording or playing, the switches other than the stop switch cannot be pushed.
      3. When no recording is present, the play switch cannot be pushed.
      4. Recording will stop after 5 seconds or when the stop switch is pushed.

    2. GPS Information Screen
      E198959E01

      1. *1: Satellite information

        HINT:
        Information from a maximum of 12 satellites is displayed on the screen. This information includes the target GPS satellite number, elevation angle, direction and signal level.

      1. *2: Receiving condition
        Screen Description 
        Display
        Content
        T
        The system is receiving a GPS signal, but is not using it for location.
        P
        The system is using the GPS signal for location.
        -
        The system cannot receive a GPS signal.
      1. *3: Measurement information
        Screen Description 
        Display
        Content
        2D
        2-dimensional location method is being used.
        3D
        3-dimensional location method is being used.
        NG
        Location data cannot be used.
        Error
        Reception error has occurred.
        -
        Any other state.
      1. *4: Position information
        Screen Description 
        Display
        Content
        Position
        Latitude and longitude information on the current position is displayed.
      1. *5: Date information
        Screen Description 
        Display
        Content
        Date
        The date/time information obtained from GPS signal is displayed in Greenwich Mean Time (GMT). The last 4 digits are displayed.

    3. Vehicle Sensors Screen
      E176506E01

      Vehicle Signal 
      Display
      Content
      *1: SPD
      SPD signal condition is displayed.
      Sensor Signal 
      Display
      Content
      *2: Gyro sensor
      Gyro sensor output condition is displayed.
      2.1 to 2.9 V

      HINT:
      Signals are updated once per second only when vehicle sensor signals are changed.

    4. Vehicle Signal Check Mode Screen
      E176505

      Screen Description 
      Display
      Content
      Battery
      Battery voltage is displayed.
      IG
      Engine switch ON/OFF state is displayed.
      PKB
      Parking brake ON/OFF state is displayed.
      REV
      Reverse signal ON/OFF state is displayed.
      SPEED
      Vehicle speed is displayed in km/h.
      TAIL
      TAIL signal (Light control switch) ON/OFF state is displayed.

      HINT:
      1. Only items sending vehicle signals will be displayed.
      2. This screen is updated once per second when input signals to the vehicle are changed.

← SYSTEM DIAGRAM (Sep 2011 – Dec 2011)HOW TO PROCEED WITH TROUBLESHOOTING (Sep 2011 – Dec 2011) →