P0722 Output Speed Sensor Circuit No Signal
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
The speed sensor SP2 detects the rotation speed of the transmission output shaft and sends signals to the ECM. The ECM determines the vehicle speed based on these signals. An AC voltage is generated in the speed sensor SP2 coil as the parking gear mounted on the rear planetary gear assembly rotates, and this voltage is sent to the ECM. The parking gear on the rear planetary gear is used as the timing rotor for this sensor.The gear shift point and lock-up timing are controlled by the ECM based on the signals from this vehicle speed sensor and the throttle position sensor signal.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0722 |
All conditions are met 5 seconds or more continuously (2 trip detection logic): (a) No signal from speed sensor SP2 is input to the ECM while 4 pulses of the No. 1 vehicle speed sensor signal are sent. (b) Vehicle speed is 9 km/h (5.59 mph) or more. (c) Park/neutral position switch is OFF. |
|
Check the waveform of the ECM connector.


- Standard:
Terminal No. (Symbol)
Tool Setting
Condition
Specified Condition
C45-101 (SP2+) - C45-100 (SP2-)
2 V/DIV., 20 msec./DIV.
Vehicle speed 20 km/h (12 mph)
Refer to illustration
MONITOR DESCRIPTION
The output speed sensor SP2 monitors the output shaft speed. The ECM controls the gear shift point and lock up timing based on the signals from the output speed sensor SP2 and throttle position sensor.If the ECM detects no signal from the output speed sensor SP2 even while the vehicle is moving, it will conclude that there is a malfunction of the output speed sensor SP2. The ECM will illuminate the MIL and store the DTC.
WIRING DIAGRAM


INSPECTION PROCEDURE
| DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Warm up the engine.
Turn the engine switch off.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the intelligent tester, read the Data List.
Engine and ECT Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
SPD (SP2)
Output shaft speed/
Min.: 0 km/h (0 mph)
Max.: 255 km/h (158 mph)
Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
-
- HINT:
- SPD (SP2) is always 0 while driving:
Open or short in the sensor or circuit.
- The SPD (SP2) value displayed on the intelligent tester is much lower than the actual vehicle speed:
Sensor trouble, improper installation, or intermittent connection trouble of the circuit.
- SPD (SP2) is always 0 while driving:
| 1. INSPECT SPEED SENSOR SP2 INSTALLATION |
Check the speed sensor SP2 installation.

- OK:
- The installation bolt is tightened properly and there is no clearance between the sensor and transmission case.
Text in Illustration *a
CORRECT
*b
INCORRECT
|
|
||||
| OK | |
| 2. INSPECT SPEED SENSOR SP2 |
Disconnect the C36 speed sensor connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
560 to 680 Ω
Text in Illustration *a
Component without harness connected
(Speed Sensor SP2)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (SPEED SENSOR SP2 - ECM) |
Disconnect the C45 ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
C45-101 (SP2+) - C45-100 (SP2-)
20°C (68°F)
560 to 680 Ω
C45-101 (SP2+) - Body ground
Always
10 kΩ or higher
C45-100 (SP2-) - Body ground
Always
10 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to ECM)
|
|
||||
| OK | ||
| ||
