2011-2013 Land Cruiser · Service Manual Drivetrain

P0818 Driveline Disconnect Switch Input Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The ECM detects the signal indicating that the transfer is in neutral.
This DTC indicates that the signal indicating that the transfer is in neutral remains on.
DTC Code
DTC Detection Condition
Trouble Area
P0818
The signal indicating that the transfer is in neutral remains ON while the vehicle is being driven under the following conditions for 30 seconds (2-trip detection logic):
  1. Vehicle speed is 25 km/h (16 mph) or more.
  2. Transfer position switch is in 4H.
  1. Short in transfer neutral position switch circuit
  2. Transfer shift actuator assembly (transfer system)
  3. ECM

MONITOR DESCRIPTION

The ECM detects whether or not the transfer is in neutral by monitoring the signal from the transfer shift actuator assembly.
If the ECM detects that the transfer is in neutral under the following conditions, the ECM will conclude that there is a malfunction of the transfer shift actuator assembly, illuminate the MIL and store the DTC:
  1. The transfer shift actuator assembly indicates that the transfer is in neutral.
  2. The transfer position switch is in the "4H" position.
  3. The vehicle is being driven at 25 km/h (16 mph) or more.
  4. The transfer neutral signal has been ON for more than 30 seconds.

WIRING DIAGRAM

C160106E20

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (TRANSFER SHIFT ACTUATOR - BODY GROUND)

  1. C209927E06
    Disconnect the C38 transfer shift actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C38-3 (N) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Transfer Shift Actuator)



NG
Go to step 2
OK

GO TO TRANSFER SYSTEM (INSPECTION) (Click here)

2. CHECK HARNESS AND CONNECTOR (FOUR WHEEL DRIVE CONTROL ECU - BODY GROUND)

  1. C209926E18
    Disconnect the A27 four wheel drive control ECU connector.

  1. Disconnect the C38 transfer shift actuator connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A27-16 (NP) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Four Wheel Drive Control ECU)



NG
Go to step 3
OK

GO TO TRANSFER SYSTEM (INSPECTION) (Click here)

3. CHECK HARNESS AND CONNECTOR (TRANSFER SHIFT ACTUATOR, FOUR WHEEL DRIVE CONTROL ECU - ECM)

  1. C197708E43
    Disconnect the A38 ECM connector.

  1. Disconnect the C38 transfer shift actuator connector.

  1. Disconnect the A27 four wheel drive control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A38-5 (TFN) - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to ECM)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← P0781 1-2 Shift (1-2 Shift Valve) (from Jan 2012)P0973 Shift Solenoid "A" Control Circuit Low (Shift Solenoid Valve S1) (+ P0974) (Sep 2011 – Dec 2011) →