FAIL-SAFE CHART
System information · Vehicles built from Jan 2012
| FAIL-SAFE CHART |
| DTC No. |
Detection Item |
Fail-safe Operation |
Fail-safe Deactivation Condition |
| P0031 |
Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P0032 |
Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P0046 |
Turbocharger / Supercharger Boost Control Solenoid Circuit Range / Performance |
The engine power is limited. |
Engine switch off |
| P0047 |
Turbocharger/ Supercharger Boost Control "A" Circuit Low |
The engine power is limited. |
Engine switch off |
| P0048 |
Turbocharger/ Supercharger Boost Control "A" Circuit High |
The engine power is limited. |
Engine switch off |
| P004B |
Turbocharger / Supercharger Boost Control Solenoid "B" Circuit Range / Performance |
The engine power is limited. |
Engine switch off |
| P004C |
Turbocharger/ Supercharger Boost Control "B" Circuit Low |
The engine power is limited. |
Engine switch off |
| P004D |
Turbocharger/ Supercharger Boost Control "B" Circuit High |
The engine power is limited. |
Engine switch off |
| P0051 |
Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P0052 |
Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P007C |
Charge Air Cooler Temperature Sensor Circuit Low |
The intake air temperature is fixed at a specified value. |
Pass condition detected |
| P007D |
Charge Air Cooler Temperature Sensor Circuit High |
The intake air temperature is fixed at a specified value. |
Pass condition detected |
| P0087 |
Fuel Rail/System Pressure - Too Low |
The engine power is reduced by 90%.* |
Engine switch off |
| P0088 |
Fuel Rail/System Pressure - Too High |
The engine power is reduced by 90%.* |
Engine switch off |
| P0093 |
Fuel System Leak Detected - Large Leak |
The engine power is reduced by 90%.* |
Engine switch off |
| P0100 |
Mass Air Flow Circuit Malfunction |
The engine power is limited. |
Pass condition detected |
| P0101 |
Mass or Volume Air Flow Circuit |
The engine power is limited. |
Engine switch off |
| P0107 |
Manifold Absolute Pressure/Barometric Pressure Circuit Low Input |
The turbo pressure is fixed at a specified value. |
Pass condition detected |
| P0108 |
Manifold Absolute Pressure/Barometric Pressure Circuit High Input |
The turbo pressure is fixed at a specified value. |
Pass condition detected |
| P0112 |
Intake Air Temperature Circuit Low Input |
The intake air temperature value is fixed. |
Pass condition detected |
| P0113 |
Intake Air Temperature Circuit High Input |
The intake air temperature value is fixed. |
Pass condition detected |
| P0115 |
Engine Coolant Temperature Circuit |
The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). |
Pass condition detected |
| P0117 |
Engine Coolant Temperature Circuit Low Input |
The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). |
Pass condition detected |
| P0118 |
Engine Coolant Temperature Circuit High Input |
The engine coolant temperature sensor output is fixed at a specified value (the fixed value varies depending on conditions). |
Pass condition detected |
| P0122 |
Throttle/Pedal Position Sensor/Switch "A" Circuit Low Input |
The engine power is limited. |
Engine switch off |
| P0123 |
Throttle/Pedal Position Sensor/Switch "A" Circuit High Input |
The engine power is limited. |
Engine switch off |
| P0180 |
Fuel Temperature Sensor "A" Circuit |
The fuel temperature is fixed at a specified value. |
Pass condition detected |
| P0182 |
Fuel Temperature Sensor "A" Circuit Low Input |
The fuel temperature is fixed at a specified value. |
Pass condition detected |
| P0183 |
Fuel Temperature Sensor "A" Circuit High Input |
The fuel temperature is fixed at a specified value. |
Pass condition detected |
| P0190 |
Fuel Rail Pressure Sensor Circuit |
|
Engine switch off |
| P0192 |
Fuel Rail Pressure Sensor Circuit Low Input |
|
Engine switch off |
| P0193 |
Fuel Rail Pressure Sensor Circuit High Input |
|
Engine switch off |
| P0201 P0202 P0203 P0204 P0205 P0206 P0207 P0208 |
Injector Circuit / Open - (Cylinder 1 to 8) |
The engine power is limited. |
Engine switch off to on (IG) or STA on |
| P0222 |
Throttle/Pedal Position Sensor/Switch "B" Circuit Low Input |
The engine power is limited. |
Engine switch off |
| P0223 |
Throttle/Pedal Position Sensor/Switch "B" Circuit High Input |
The engine power is limited. |
Engine switch off |
| P0299 |
Turbocharger / Supercharger Underboost |
The engine power is limited. |
Pass condition detected |
| P0335 |
Crankshaft Position Sensor "A" Circuit |
The engine power is reduced by 90%.* |
Pass condition detected |
| P0339 |
Crankshaft Position Sensor "A" Circuit Intermittent |
The engine power is reduced by 90%.* |
Pass condition detected |
| P0340 |
Camshaft Position Sensor "A" Circuit (Bank 1 or Single Sensor) |
The engine power is reduced by 90%.* |
Pass condition detected |
| P0400 |
Exhaust Gas Recirculation Flow |
The engine power is limited. |
Engine switch off |
| P0405 |
Exhaust Gas Recirculation Sensor "A" Circuit Low |
The engine power is limited. |
Engine switch off |
| P0406 |
Exhaust Gas Recirculation Sensor "A" Circuit High |
The engine power is limited. |
Engine switch off |
| P0407 |
Exhaust Gas Recirculation Sensor "B" Circuit Low |
The engine power is limited. |
Engine switch off |
| P0408 |
Exhaust Gas Recirculation Sensor "B" Circuit High |
The engine power is limited. |
Engine switch off |
| P042E |
Exhaust Gas Recirculation "A" Control Stuck Open |
The engine power is limited. |
Engine switch off |
| P045E |
Exhaust Gas Recirculation "B" Control |
The engine power is limited. |
Engine switch off |
| P0500 |
Vehicle Speed Sensor "A" |
The vehicle speed is fixed at 0 km/h (0 mph). |
Pass condition detected |
| P0545 |
Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 1) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P0546 |
Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 1) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P0548 |
Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 1) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P0549 |
Exhaust Gas Temperature Sensor Circuit High (Bank 2 Sensor 1) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P0606 |
ECM / PCM Processor |
The engine power is reduced by 90%.* |
Pass condition detected |
| P060A |
Internal Control Module Monitoring Processor Performance |
The engine power is reduced by 90%.* |
Pass condition detected |
| P060B |
Internal Control Module A/D Processing Performance |
The engine power is reduced by 90%.* |
Pass condition detected |
| P0627 |
Fuel Pump Control Circuit / Open |
The engine power is limited. |
Pass condition detected |
| P062D |
No. 1 Fuel Injector Driver Circuit Performance |
|
Engine switch off |
| P062E |
No. 2 Fuel Injector Driver Circuit Performance |
|
Engine switch off |
| P1229 |
Fuel Pump System |
The engine power is limited. |
Engine switch off |
| P1251 |
Turbocharger / Supercharger Overboost Condition (Too High) |
The engine power is limited. |
Engine switch off |
| P1271 |
Fuel Regulator Circuit Malfunction (EDU Drive) |
The engine power is limited. |
Engine switch off |
| P1272 |
Fuel Pressure Regulator Malfunction |
The engine power is limited. |
Engine switch off |
| P1626 |
Idle Signal Output Value Low |
The engine power is limited. |
Engine switch off |
| P1627 |
Idle Signal Output Value High |
The engine power is limited. |
Engine switch off |
| P1629 |
Idle Signal Output Value Low Bank 2 |
The engine power is limited. |
Engine switch off |
| P162A |
Idle Signal Output Value High Bank 2 |
The engine power is limited. |
Engine switch off |
| P200C |
Diesel Particulate Filter Over Temperature Bank 1 |
PM forced regeneration is prohibited. |
Engine switch off |
| P200D |
Diesel Particulate Filter Temperature Too High |
PM forced regeneration is prohibited. |
Engine switch off |
| P200E |
Catalyst System Temperature Too High Bank 1 |
PM forced regeneration is prohibited. |
Engine switch off |
| P200F |
Catalyst System Temperature Too High Bank 2 |
PM forced regeneration is prohibited. |
Engine switch off |
| P2032 |
Exhaust Gas Temperature Sensor Circuit Low (Bank 1 Sensor 2) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2033 |
Exhaust Gas Temperature Sensor Circuit High (Bank 1 Sensor 2) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2035 |
Exhaust Gas Temperature Sensor Circuit Low (Bank 2 Sensor 2) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2036 |
Exhaust Gas Temperature Sensor Circuit High (Bank 2 Sensor 2) |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2084 |
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 2 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2086 |
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 2 Sensor 2 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P20CD |
Open in Exhaust Aftertreatment Fuel Injector "A" Control Circuit |
|
Pass condition detected |
| P20CF |
Exhaust Aftertreatment Fuel Injector "A" Stuck Open |
The engine power is reduced by 90%.* |
Pass condition detected |
| P20D3 |
Open in Exhaust Aftertreatment Fuel Injector "B" Control Circuit |
|
Pass condition detected |
| P20D5 |
Exhaust Aftertreatment Fuel Injector "B" Stuck Open |
The engine power is reduced by 90%.* |
Pass condition detected |
| P2120 |
Throttle/Pedal Position Sensor/Switch "D" Circuit |
The engine power is limited. |
Engine switch off |
| P2121 |
Throttle/Pedal Position Sensor/Switch "D" Circuit Range/Performance |
The engine power is limited. |
Engine switch off |
| P2122 |
Throttle/Pedal Position Sensor/Switch "D" Circuit Low Input |
The engine power is limited. |
Engine switch off |
| P2123 |
Throttle/Pedal Position Sensor/Switch "D" Circuit High Input |
The engine power is limited. |
Engine switch off |
| P2125 |
Throttle/Pedal Position Sensor/Switch "E" Circuit |
The engine power is limited. |
Engine switch off |
| P2127 |
Throttle/Pedal Position Sensor/Switch "E" Circuit Low Input |
The engine power is limited. |
Engine switch off |
| P2128 |
Throttle/Pedal Position Sensor/Switch "E" Circuit High Input |
The engine power is limited. |
Engine switch off |
| P2138 |
Throttle/Pedal Position Sensor/Switch "D"/"E" Voltage Correlation |
The engine power is limited. |
Engine switch off |
| P213B |
Exhaust Gas Recirculation Throttle Position Control (Range/Performance) |
The engine power is limited. |
Engine switch off |
| P2195 |
Oxygen (A/F) Sensor Signal Stuck Lean (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2197 |
Oxygen (A/F) Sensor Signal Stuck Lean (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2226 |
Barometric Pressure Circuit |
The atmospheric pressure is fixed at a specified value. |
Pass condition detected |
| P2228 |
Barometric Pressure Circuit Low Input |
The atmospheric pressure is fixed at a specified value. |
Pass condition detected |
| P2229 |
Barometric Pressure Circuit High Input |
The atmospheric pressure is fixed at a specified value. |
Pass condition detected |
| P2237 |
Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2238 |
Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2239 |
Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2240 |
Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2241 |
Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2242 |
Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2252 |
Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2253 |
Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2255 |
Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2256 |
Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |
The power to the air fuel ratio sensor and air fuel ratio sensor heater is stopped. |
Pass condition detected |
| P2428 |
Exhaust Gas Temperature Too High Bank 1 |
PM forced regeneration is prohibited. |
Engine switch off |
| P2429 |
Exhaust Gas Temperature Too High Bank 2 |
PM forced regeneration is prohibited. |
Engine switch off |
| P242B |
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 1 Sensor 3 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P242C |
Exhaust Gas Temperature Sensor Circuit Low Bank 1 Sensor 3 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P242D |
Exhaust Gas Temperature Sensor Circuit High Bank 1 Sensor 3 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P244B |
Diesel Particulate Filter Differential Pressure Too High |
|
Engine switch off |
| P244C |
Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 1 |
PM forced regeneration is prohibited. |
Engine switch off |
| P244E |
Exhaust Temperature Too Low for Particulate Filter Regeneration Bank 2 |
PM forced regeneration is prohibited. |
Engine switch off |
| P2458 |
Diesel Particulate Filter Regeneration Duration |
PM forced regeneration is prohibited. |
Engine switch off |
| P2463 |
Diesel Particulate Filter Restriction - Soot Accumulation |
|
Pass condition detected |
| P2465 |
Diesel Particulate Filter Differential Pressure Too High Bank 2 |
|
Engine switch off |
| P2467 |
Exhaust Gas Temperature Sensor Circuit Range/Performance Bank 2 Sensor 3 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2468 |
Exhaust Gas Temperature Sensor Circuit Low Bank 2 Sensor 3 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2469 |
Exhaust Gas Temperature Sensor Circuit High Bank 2 Sensor 3 |
PM forced regeneration is prohibited. |
Pass condition detected |
| P2564 |
Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit Low |
The engine power is limited. |
Engine switch off |
| P2565 |
Turbocharger/ Supercharger Boost Control Position Sensor "A" Circuit High |
The engine power is limited. |
Engine switch off |
| P2588 |
Turbocharger/ Supercharger Boost Control Position Sensor "B" Circuit Low |
The engine power is limited. |
Engine switch off |
| P2589 |
Turbocharger/ Supercharger Boost Control Position Sensor "B" Circuit High |
The engine power is limited. |
Engine switch off |
- HINT:
- *: Engine power is limited immediately after the DTC is stored.