2011-2013 Land Cruiser · Service Manual Drivetrain

INSTALLATION

Removal / installation · Vehicles built from Sep 2011


1. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

D027914E09
Text in Illustration 
*1
Check Ball Body
*2
Spring
  1. Install the spring and check ball body.

  1. C162146E02
    Insert the pin of the manual valve into the hole of the manual valve lever.
    Text in Illustration 
    *1
    Pin

  1. C162147E01
    Install the 19 bolts.

    Torque:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    36 mm (1.42 in.) for bolt A
    25 mm (0.984 in.) for bolt B
    45 mm (1.77 in.) for bolt C
    50 mm (1.97 in.) for bolt D

  1. Install the detent spring and detent spring cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


2. CONNECT TRANSMISSION WIRE

C161112E03
Text in Illustration 
*a
Orange
*b
Blue
  1. Connect the 9 connectors to the solenoid valves.

  1. Connect the 2 ATF temperature sensors with the 2 clamps and 2 bolts.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    12 mm (0.472 in.) for bolt A

    36 mm (1.41 in.) for bolt B


3. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

C178807
  1. Coat a new O-ring with ATF and install it to the oil strainer.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


4. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY

C178809E04
Text in Illustration 
*1
Magnet
  1. Install the 4 transmission oil cleaner magnets to the oil pan.

  1. C178808E01
    Install a new gasket and the oil pan with the 12 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }


    NOTICE:
    C157303E02
    1. Make sure that there is no oil or foreign matter on the gasket seal surface and oil pan contact surface.
    2. Install the gasket so that there is no slack in the gasket, and make sure the entire circumference of the seal surface is level.
    3. Make sure that the 9 gasket drop prevention protrusions are set on the oil pan.
    4. When tightening the bolts of the oil pan, make sure that the gasket is not pinched between the gasket tightening area sleeve and the transmission seal surface.

    Text in Illustration 
    *1
    Sleeve
    *2
    Protrusion
    *a
    Correct
    *b
    Incorrect


5. RESET MEMORY
for 3UR-FE: (Click here)
for 1VD-FTV: (Click here)

6. ADD AUTOMATIC TRANSMISSION FLUID
(Click here)

7. INSTALL OIL PAN PROTECTOR ASSEMBLY

C171483
  1. Install the oil pan protector with the 4 bolts.

    Torque:
    63 N*m{ 642 kgf*cm , 46 ft.*lbf }


8. INSTALL NO. 2 ENGINE UNDER COVER

C178816
  1. Install the under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

← REASSEMBLY (from Sep 2011)COMPONENTS (Sep 2011 – Dec 2011) →