2011-2013 Land Cruiser · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. BEARING POSITION

C171522E01

Bearing and Race Diameter:
Mark
Front Race Diameter Inside/Outside
Thrust Bearing Diameter Inside/Outside
Rear Race Diameter Inside/Outside
A
74.3 to 74.6 mm (2.93 to 2.94 in.)/87.4 to 87.7 mm (3.44 to 3.45 in.)
72.0 to 72.3 mm (2.83 to 2.85 in.)/85.3 to 85.6 mm (3.36 to 3.37 in.)
-
B
37.0 to 37.3 mm (1.46 to 1.47 in.)/52.1 to 52.3 mm (2.05 to 2.06 in.)
34.7 to 34.9 mm (1.366 to 1.374 in.)/51.6 to 51.9 mm (2.03 to 2.04 in.)
-
C
-
21.4 to 21.6 mm (0.841 to 0.850 in.)/40.8 to 41.0 mm (1.606 to 1.614 in.)
22.7 to 22.9 mm (0.892 to 0.902 in.)/60.0 to 60.4 mm (2.36 to 2.38 in.)
D
33.3 to 33.5 mm (1.31 to 1.32 in.)/56.3 to 56.6 mm (2.22 to 2.23 in.)
38.5 to 38.7 mm (1.515 to 1.524 in.)/56.5 to 57.0 mm (2.22 to 2.24 in.)
-
E
-
42.6 to 42.8 mm (1.68 to 1.69 in.)/60.8 to 61.1 mm (2.39 to 2.41 in.)
-
F
38.0 to 38.2 mm (1.496 to 1.504 in.)/56.5 to 57.0 mm (2.22 to 2.24 in.)
43.4 to 43.6 mm (1.71 to 1.72 in.)/58.0 to 58.4 mm (2.28 to 2.30 in.)
-
G
-
55.8 to 56.0 mm (2.197 to 2.204 in.)/76.1 to 76.4 mm (2.996 to 3.008 in.)
53.8 to 54.0 mm (2.12 to 2.13 in.)/73.7 to 74.0 mm (2.90 to 2.91 in.)
H
33.4 to 33.6 mm (1.31 to 1.32 in.)/48.7 to 49.0 mm (1.92 to 1.93 in.)
32.2 to 32.3 mm (1.268 to 1.272 in.)/49.0 to 49.2 mm (1.93 to 1.94 in.)
32.2 to 32.4 mm (1.27 to 1.28 in.)/48.7 to 49.0 mm (1.92 to 1.93 in.)
I
-
21.5 to 21.8 mm (0.846 to 0.858 in.)/40.5 to 40.8 mm (1.59 to 1.61 in.)
-
J
-
43.6 to 43.9 mm (1.72 to 1.73 in.)/60.6 to 60.9 mm (2.39 to 2.40 in.)
47.2 to 47.4 mm (1.86 to 1.87 in.)/66.9 to 67.1 mm (2.63 to 2.64 in.)


2. ASSEMBLE NO. 4 BRAKE PISTON AND BRAKE REACTION SLEEVE

D028795E09
  1. Coat 2 new O-rings with ATF, and install them to the brake reaction sleeve.

  1. Coat 2 new O-rings with ATF, and install them to the No. 4 brake piston.

  1. Install the No. 4 brake piston to the reaction sleeve.


3. INSTALL NO. 4 BRAKE PISTON WITH BRAKE REACTION SLEEVE

D028080E03
  1. Install the No. 4 brake piston with brake reaction sleeve to the transmission case

    NOTICE:
    1. Do not damage the O-rings.
    2. Make sure the No. 4 brake piston is underneath the brake reaction sleeve.


4. INSTALL 1ST AND REVERSE BRAKE PISTON

D028081E03
  1. Coat a new O-ring with ATF.

  1. Install the O-ring to the 1st and reverse brake piston.

  1. With the spring seat of the piston facing upwards (the front side), place the piston in the transmission case.

    NOTICE:
    Be careful not to damage the O-ring.

  1. D028549E01
    Place the brake return spring onto the 1st and reverse brake piston.


5. INSTALL 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY

  1. D028082E01
    Place SST on a new spring retainer, and compress the return spring.
    SST
    09350-30020   (09350-07050)

  1. Using SST, install the snap ring.

    SST
    09350-30020   (09350-07070)


6. INSTALL REAR PLANETARY GEAR ASSEMBLY

  1. D027947E02
    Install the No. 9 thrust bearing race.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    No. 9 Race
    47.2 to 47.4 mm (1.86 to 1.87 in.)
    66.9 to 67.1 mm (2.63 to 2.64 in.)

  1. D027946E05
    Coat the 2 thrust needle roller bearings with petroleum jelly, and install them to the rear planetary gear.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing J
    43.6 to 43.9 mm (1.72 to 1.73 in.)
    60.6 to 60.9 mm (2.39 to 2.40 in.)
    Bearing I
    21.5 to 21.8 mm (0.846 to 0.858 in.)
    40.5 to 40.8 mm (1.59 to 1.61 in.)

  1. D027945E01
    Install the rear planetary gear assembly.


7. INSPECT PACK CLEARANCE OF 1ST AND REVERSE BRAKE

  1. D027966E01
    Make sure the 1st and reverse brake piston moves smoothly when applying and releasing compressed air into the transmission case.

  1. D029831E01
    Using a vernier caliper, measure the level difference (length A) between the upper surface of the 1st and reverse brake piston and the hitting surface of the No. 4 brake flange at both ends across a diameter, and calculate the average.

    NOTICE:
    The 1st and reverse brake piston must be installed tightly to the end face of the transmission case.

    HINT:
    Length A = 36.35 to 37.09 mm (1.43 to 1.46 in.)

  1. D029832E03
    Using a vernier caliper, measure the thickness (length B) of the 2 brake flanges, 7 No. 4 brake plates and 8 No. 4 brake discs all together at both ends across a diameter, and calculate the average.

    HINT:
    Pack clearance = Length A - Length B - 0.25 mm to 1.8 mm (0.00984 to 0.0709 in.)
    Length B = 36.04 to 37.14 mm (1.42 to 1.46 in.)

    Standard pack clearance:
    0.8 to 1.1 mm (0.0315 to 0.0433 in.)

    If the pack clearance is outside the standard, select and install a brake flange that makes the pack clearance within the standard.

    H Thickness:
    No.
    Thickness
    0
    0 mm (0 in.)
    2
    0.15 to 0.25 mm (0.00590 to 0.00984 in.)
    4
    0.35 to 0.45 mm (0.0138 to 0.0177 in.)
    6
    0.55 to 0.65 mm (0.0217 to 0.0256 in.)
    8
    0.75 to 0.85 mm (0.0295 to 0.0335 in.)
    10
    0.95 to 1.05 mm (0.0374 to 0.0413 in.)
    12
    1.15 to 1.25 mm (0.0453 to 0.0492 in.)
    14
    1.35 to 1.45 mm (0.0531 to 0.0571 in.)


8. INSTALL NO. 4 BRAKE DISC

  1. D027944E01
    Install the 2 flanges, 8 discs and 7 plates.

    Install in order:
    F - D - P - D - P - D - P - D - P - D - P - D - P - D - P - D - F

    HINT:
    F = Flange
    D = Disc
    P = Plate


9. INSTALL BRAKE PLATE STOPPER SPRING

D027943E01

10. INSTALL REAR PLANETARY RING GEAR FLANGE SUB-ASSEMBLY

  1. D027965E11
    Install the No. 8 thrust bearing race, thrust needle roller bearing, No. 7 thrust bearing race and planetary ring gear flange to the intermediate shaft.

    Thrust Needle Roller Bearing and Race Diameter:
    Item
    Inside
    Outside
    No. 7 Race
    33.4 to 33.6 mm (1.31 to 1.32 in.)
    48.7 to 49.0 mm (1.92 to 1.93 in.)
    Bearing
    32.2 to 32.3 mm (1.268 to 1.272 in.)
    49.0 to 49.2 mm (1.93 to 1.94 in.)
    No. 8 Race
    32.2 to 32.4 mm (1.27 to 1.28 in.)
    48.7 to 49.0 mm (1.92 to 1.93 in.)


11. INSTALL NO. 3 1-WAY CLUTCH ASSEMBLY

  1. D027964E01
    Install the 1-way clutch and 1-way clutch inner race to the intermediate shaft.


12. INSTALL INTERMEDIATE SHAFT

  1. D027942E01
    Install the intermediate shaft with No. 3 1-way clutch assembly to the case.

  1. D027927E03
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


13. INSTALL CENTER PLANETARY GEAR ASSEMBLY

  1. D027940E01
    Install the planetary sun gear and center planetary gear to the case.

  1. Coat the No. 6 thrust bearing race with petroleum jelly, and install it to the center planetary gear.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    Race
    53.8 to 54.0 mm (2.12 to 2.13 in.)
    73.7 to 74.0 mm (2.90 to 2.91 in.)


14. INSTALL NO. 2 BRAKE PISTON

  1. D028797E07
    Coat 2 new O-rings with ATF, and install them to the brake piston.

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.

  1. Install the No. 2 brake piston to the case.


15. INSTALL NO. 2 BRAKE DISC

D027938E04
  1. Install the brake piston return spring.

  1. Install the 3 plates, 3 discs and flange.

    Install in order:
    D - P - D - P - D - P - F

    HINT:
    D = Disc
    P = Plate
    F = Flange

  1. D028818E03
    Using SST and a press, compress the return spring and install the No. 2 brake spring snap ring.
    SST
    09351-40010  


16. INSTALL NO. 1 BRAKE PISTON

  1. D028539E10
    Coat 2 new O-rings with ATF, and install them to the brake piston.

  1. Press the brake piston into the brake cylinder with both hands.

    NOTICE:
    Be careful not to damage the O-rings.


17. INSTALL BRAKE PISTON RETURN SPRING SUB-ASSEMBLY

  1. D027935E01
    Install the brake piston return spring and the No. 1 brake piston with No. 1 brake cylinder to the transmission case.


18. INSTALL BRAKE PISTON RETURN SPRING SNAP RING

  1. D028819E04
    Using SST and a press, compress the return spring and install the brake piston return spring snap ring.
    SST
    09351-40010  


19. INSTALL NO. 1 BRAKE DISC

D027933E04
  1. for 1GR-FE:
    Install the 3 plates, 3 discs and flange.

    Install in order:
    P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange

  1. C162132E01
    for 2UZ-FE:
    Install the 4 plates, 4 discs and flange.

    Install in order:
    P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange


20. INSTALL CENTER PLANETARY RING GEAR

  1. D028541E01
    Install the center planetary ring gear and front planetary ring gear flange to the front planetary ring gear.

  1. D028540E01
    Using a screwdriver, install the snap ring.


21. INSTALL FRONT PLANETARY RING GEAR

  1. D027932E01
    Install the front planetary ring gear and thrust needle roller bearing to the case.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing
    55.8 to 56.0 mm (2.197 to 2.204 in.)
    76.1 to 76.4 mm (2.996 to 3.008 in.)


22. INSTALL FRONT PLANETARY GEAR ASSEMBLY

  1. D027931E04
    Install the thrust washer and thrust needle roller bearing.

  1. Coat the No. 5 thrust race with petroleum jelly, and install it to the front planetary ring gear.

    Thrust Needle Roller Bearing and Race Diameter:
    Item
    Inside
    Outside
    Bearing
    43.4 to 43.6 mm (1.71 to 1.72 in.)
    58.0 to 58.4 mm (2.28 to 2.30 in.)
    Race
    38.0 to 38.2 mm (1.496 to 1.504 in.)
    56.5 to 57.0 mm (2.22 to 2.24 in.)

  1. D027930E01
    Install the front planetary gear assembly and 1-way clutch inner race to the case.


23. INSPECT PISTON STROKE OF NO. 1 BRAKE PISTON

  1. D028814E01
    Make sure the No. 1 brake piston moves smoothly when applying and releasing compressed air into the transmission case.

  1. D028815E01
    Using a feeler gauge, measure the B3 brake pack clearance between the snap ring and flange.

    Standard piston stroke:
    0.42 to 0.72 mm (0.0165 to 0.0283 in.)

    If the piston stroke is outside the specification, parts may have been assembled incorrectly. Perform the reassembly again. If the piston stroke is still outside the specification, select another flange.

    HINT:
    There are 4 different thicknesses for the flange.

    Flange Thickness:
    Mark
    Thickness
    0
    1.95 to 2.05 mm (0.0768 to 0.0807 in.)
    1
    2.15 to 2.25 mm (0.0846 to 0.0886 in.)
    2
    2.35 to 2.45 mm (0.0925 to 0.0965 in.)
    3
    2.55 to 2.65 mm (0.100 to 0.104 in.)


24. INSTALL 2ND BRAKE PISTON

  1. D028546E11
    Coat 2 new O-rings with ATF, and install them to the 2nd brake piston.

  1. Press the 2nd brake cylinder into the 2nd brake piston with both hands.

    NOTICE:
    Be careful not to damage the O-rings.

  1. D028817E04
    Using SST and a press, compress the return spring and install the snap ring.
    SST
    09351-40010  

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


25. INSTALL 2ND BRAKE CYLINDER

  1. D027929E01
    Install the 2nd brake cylinder to the case.


26. INSTALL 1-WAY CLUTCH ASSEMBLY

  1. D027928E01
    Install the thrust washer and 1-way clutch to the case.


27. INSTALL 2ND BRAKE PISTON HOLE SNAP RING

  1. D027927E03
    Using SST, install the snap ring.
    SST
    09350-30020   (09350-07060)


28. INSTALL NO. 3 BRAKE DISC

  1. D027926E05
    Install the cushion plate, 4 plates, 4 discs and flange to the case.

    Install in order:
    C - P - D - P - D - P - D - P - D - F

    HINT:
    C = Cushion plate
    P = Plate
    D = Disc
    F = Flange


29. INSTALL NO. 3 BRAKE SNAP RING

  1. D027925E01
    Using a screwdriver, install the snap ring.


30. INSTALL DIRECT CLUTCH PISTON SUB-ASSEMBLY

  1. D028816E02
    Coat 2 new O-rings with ATF, and install them to the direct clutch piston.

  1. D028517E01
    Install the No. 2 clutch balancer and direct clutch return spring to the direct clutch piston.

  1. D028516E02
    Coat a new O-ring with ATF, and install it to the clutch drum.

  1. Press the direct clutch piston into the clutch drum with both hands.

    NOTICE:
    Be careful not to damage the O-rings.

  1. D028514E05
    Place SST on the direct clutch piston, and compress the return spring with a press.

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring sheet from being deformed.

    SST
    09320-89010  
    09350-30020   (09350-07070)

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.

  1. D028536E07
    Set the end gap of the snap ring in the piston as shown in the illustration

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


31. INSTALL REVERSE CLUTCH PISTON SUB-ASSEMBLY

  1. D028513E02
    Coat a new O-ring with ATF, and install it to the clutch drum.

  1. D028512E02
    Coat a new O-ring with ATF, and install it to the reverse clutch piston.

  1. D028511E01
    Press the clutch drum into the reverse clutch piston with both hands.

    NOTICE:
    Be careful not to damage the O-ring.


32. INSTALL REVERSE CLUTCH RETURN SPRING SUB-ASSEMBLY

  1. D028510E02
    Coat a new O-ring with ATF, and install it to the reverse clutch piston.

  1. Install the reverse clutch return spring to the reverse clutch piston.


33. INSTALL NO. 3 CLUTCH BALANCER

  1. D028509E04
    Place SST on the No. 3 clutch balancer, and compress the clutch balancer with a press.

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

    SST
    09387-00070  
    09350-30020   (09350-07070)

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.

  1. D028534E02
    Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


34. INSTALL DIRECT CLUTCH DISC

C162137E01
  1. for 1GR-FE:
    Install the 5 plates, 5 discs and reverse clutch flange to the clutch drum.

    Install in order:
    P - D - P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange

  1. C162138E01
    for 2UZ-FE:
    Install the 6 plates, 6 discs and reverse clutch flange to the clutch drum.

    Install in order:
    P - D - P - D - P - D - P - D - P - D - P - D - F

    HINT:
    P = Plate
    D = Disc
    F = Flange

  1. D028507E01
    Using a screwdriver, install the 2 hole snap rings to the clutch drum.


35. INSPECT PACK CLEARANCE OF DIRECT CLUTCH

  1. D029841E02
    Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while applying air to the oil hole as shown in the illustration, and calculate the average.

    Standard pack clearance for 1GR-FE:
    0.5 to 0.8 mm (0.0197 to 0.0315 in.)

    Standard pack clearance for 2UZ-FE:
    0.6 to 0.9 mm (0.0236 to 0.0354 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.4 mm (0.134 in.)) to the position of the shaded area in the illustration.

    HINT:
    Flange moving distance A = 0.26 to 1.14 mm (0.0102 to 0.0449 in.)
    Pack clearance = Flange moving distance A - 0.05 mm (0.00197 in.)

    If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.

    Flange Thickness:
    Mark
    Thickness
    2
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    3
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    4
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    5
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    6
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    7
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    8
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    9
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    A
    3.75 to 3.85 mm (0.148 to 0.152 in.)


36. INSTALL REVERSE CLUTCH FLANGE

  1. D028506E01
    Install the reverse clutch flange to the clutch drum.


37. INSTALL REVERSE CLUTCH REACTION SLEEVE

D031540E02
  1. Install the 5 reverse clutch discs, 4 clutch plates, reverse clutch flange, clutch cushion plate and reverse clutch reaction sleeve to the reverse clutch hub.

    Install in order:
    D - P - D - P - D - P - D - P - D - F - C - S

    HINT:
    D = Disc
    P = Plate
    F = Flange
    C = Cushion plate
    S = Sleeve

  1. Using a screwdriver, install the hole snap ring.


38. INSPECT PACK CLEARANCE OF REVERSE CLUTCH

  1. Using a dial indicator, measure the reverse clutch piston stroke (distance A) and the moving distance (distance B) of the reverse flange at both ends across a diameter while applying air (392 kPa (4.0 kgf/cm2, 57 psi)) to the oil hole as shown in the illustration, and calculate the average.

    Standard pack clearance:
    0.5 to 0.8 mm (0.0197 to 0.0315 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.3 mm (0.130 in.)) to the position of the shaded area in the illustration.

    HINT:
    Piston stroke A = 1.05 to 2.15 mm (0.0413 to 0.0846 in.)
    Flange moving distance B = 0.72 to 1.08 mm (0.0283 to 0.0425 in.)
    Pack clearance = Piston stroke A - Flange moving distance B - 0.06 mm (0.00236 in.)


    D028538E02
    If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.

    Flange Thickness:
    Mark
    Thickness
    0
    2.75 to 2.85 mm (0.108 to 0.112 in.)
    1
    2.85 to 2.95 mm (0.112 to 0.116 in.)
    2
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    3
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    4
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    5
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    6
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    7
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    8
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    9
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    A
    3.75 to 3.85 mm (0.148 to 0.152 in.)


39. REMOVE REVERSE CLUTCH REACTION SLEEVE

  1. D029844E01
    Using a screwdriver, remove the snap ring from the clutch drum.

  1. D029843E01
    Remove the reverse clutch reaction sleeve, clutch cushion plate, reverse clutch flange, 5 reverse clutch discs, and 4 clutch plates from the reverse clutch hub.


40. INSTALL FORWARD CLUTCH PISTON

  1. D028525E02
    Coat 2 new O-rings with ATF, and install them to the forward clutch piston.


41. INSTALL NO. 1 CLUTCH BALANCER

  1. D028523E02
    Coat a new O-ring with ATF and install it to the clutch balancer.

  1. D028522E01
    Install the clutch balancer and forward clutch return spring.

    NOTICE:
    Be careful not to damage the O-ring.

  1. D028521E02
    Place SST on the No. 1 clutch balancer, and compress the return spring with a press.

    NOTICE:
    Stop pressing when the spring sheet is lowered to a position 1 to 2 mm (0.0393 to 0.0787 in.) from the snap ring groove to prevent the spring sheet from being deformed.

    SST
    09350-30020   (09350-07040, 09350-07070)

  1. Install the snap ring with a snap ring expander.

    NOTICE:
    Do not expand the snap ring excessively.

  1. D028535E02
    Set the end gap of the snap ring in the piston as shown in the illustration.

    NOTICE:
    Be sure the end gap of the snap ring is not aligned with the spring retainer claw.


42. INSTALL FORWARD MULTIPLE DISC CLUTCH DISC

D028520E02
  1. for 1GR-FE:
    Install the 2 flanges, 6 discs and 5 plates to the input shaft assembly.

    Install in order:
    F- D - P - D - P - D - P - D - P - D - P - D - F

    HINT:
    F = Flange
    D = Disc
    P = Plate

  1. C115806E01
    for 2UZ-FE:
    Install the 2 flanges, 7 discs and 6 plates to the input shaft assembly.

    Install in order:
    F- D - P - D - P - D - P - D - P - D - P - D - P - D - F

    HINT:
    F = Flange
    D = Disc
    P = Plate

  1. D028519E01
    Using a screwdriver, install the hole snap ring.


43. INSTALL INPUT SHAFT OIL SEAL RING

  1. D029677E01
    Coat 3 new oil seal rings with ATF.

  1. Squeeze the ends of the 3 oil seal rings together, and then install them to the starter shaft groove.

    NOTICE:
    Do not excessively widen the ring.

    HINT:
    After installing the oil seal rings, check that they rotate smoothly.


44. INSPECT PACK CLEARANCE OF FORWARD CLUTCH

  1. D028537E02
    Using a dial indicator, measure the moving distance (distance A) of the clutch flange at both ends across a diameter while applying air to the oil hole as shown in the illustration, and calculate the average.

    Standard pack clearance for 1GR-FE:
    0.6 to 0.9 mm (0.0236 to 0.0354 in.)

    Standard pack clearance for 2UZ-FE:
    0.8 to 1.0 mm (0.0315 to 0.0394 in.)

    NOTICE:
    When measuring the moving distance, install a standard flange (thickness: 3.4 mm (0.134 in.)) to the position of the shaded area in the illustration.

    HINT:
    Flange moving distance A = 0.26 to 1.36 mm (0.0102 to 0.0535 in.)
    Pack clearance = Flange moving distance A - 0.01 mm (0.000394 in.)

    If the pack clearance is outside the standard, select and install a clutch flange that makes the pack clearance within the standard.

    Flange Thickness:
    Mark
    Thickness
    0
    2.95 to 3.05 mm (0.116 to 0.120 in.)
    1
    3.05 to 3.15 mm (0.120 to 0.124 in.)
    2
    3.15 to 3.25 mm (0.124 to 0.128 in.)
    3
    3.25 to 3.35 mm (0.128 to 0.132 in.)
    4
    3.35 to 3.45 mm (0.132 to 0.136 in.)
    5
    3.45 to 3.55 mm (0.136 to 0.140 in.)
    6
    3.55 to 3.65 mm (0.140 to 0.144 in.)
    7
    3.65 to 3.75 mm (0.144 to 0.148 in.)
    8
    3.75 to 3.85 mm (0.148 to 0.152 in.)
    9
    3.85 to 3.95 mm (0.148 to 0.152 in.)
    A
    3.95 to 4.05 mm (0.152 to 0.159 in.)


45. INSTALL INPUT SHAFT ASSEMBLY

  1. D028505E01
    Install the input shaft to the clutch drum.

  1. D028504E01
    Install the thrust needle roller bearing to the clutch drum.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing
    21.4 to 21.6 mm (0.841 to 0.850 in.)
    40.8 to 41.0 mm (1.606 to 1.614 in.)


46. INSTALL MULTIPLE DISC CLUTCH HUB

  1. D028503E06
    Coat the 2 thrust bearing races with petroleum jelly, and install them onto the multiple disc clutch hub.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    No. 3 Race
    22.7 to 22.9 mm (0.892 to 0.902 in.)
    60.0 to 60.4 mm (2.36 to 2.38 in.)
    No. 4 Race
    33.3 to 33.5 mm (1.31 to 1.32 in.)
    56.3 to 56.6 mm (2.22 to 2.23 in.)

  1. D028502E01
    Install the multiple disc clutch hub to the clutch drum.


47. INSTALL FORWARD CLUTCH HUB SUB-ASSEMBLY

  1. D028500E05
    Coat the 2 thrust needle roller bearings with petroleum jelly, and install them to the forward clutch hub.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing D
    38.5 to 38.7 mm (1.515 to 1.524 in.)
    56.5 to 57.0 mm (2.22 to 2.24 in.)
    Bearing E
    42.6 to 42.8 mm (1.68 to 1.69 in.)
    60.8 to 61.1 mm (2.39 to 2.41 in.)

  1. D028001E01
    Install the forward clutch hub to the clutch drum.


48. INSTALL REAR CLUTCH DISC

  1. D027999E14
    Install the 5 discs, 4 plates, reverse clutch flange and clutch cushion plate to the reverse clutch hub.

    Install in order:
    D - P - D - P - D - P - D - P - D - F - C

    HINT:
    D = Disc
    P = Plate
    F = Flange
    C = Cushion plate


49. INSTALL REVERSE CLUTCH REACTION SLEEVE

  1. D027998E01
    Install the reverse clutch reaction sleeve to the reverse clutch hub.


50. INSTALL REVERSE CLUTCH HUB SUB-ASSEMBLY

  1. D027997E01
    Install the reverse clutch hub to the clutch drum.

  1. D027996E01
    Using a screwdriver, install the snap ring to the clutch drum and input shaft.


51. INSTALL NO. 2 1-WAY CLUTCH ASSEMBLY

  1. D027994E01
    Coat the No. 2 clutch drum thrust washer with petroleum jelly and install it to the clutch drum.

  1. Install the 1-way clutch to the clutch drum.


52. INSTALL CLUTCH DRUM AND INPUT SHAFT ASSEMBLY

  1. C177432E01
    Coat the 2 thrust needle roller bearings and clutch drum thrust washer with petroleum jelly and install them to the clutch drum and input shaft assembly.

    Thrust Needle Roller Bearing Diameter:
    Item
    Inside
    Outside
    Bearing A
    72.0 to 72.3 mm (2.83 to 2.85 in.)
    85.3 to 85.6 mm (3.36 to 3.37 in.)
    Bearing A
    34.7 to 34.9 mm (1366 to 1.374 in.)
    51.6 to 51.9 mm (2.03 to 2.04 in.)

  1. D029833E01
    Install the clutch drum and input shaft assembly to the transmission case.


53. INSTALL OIL PUMP ASSEMBLY

  1. C177431E01
    Coat the No. 1 and No. 2 thrust bearing races with petroleum jelly, and install them to the front oil pump.

    Thrust Bearing Race Diameter:
    Item
    Inside
    Outside
    No. 1 Race
    74.3 to 74.6 mm (2.93 to 2.94 in.)
    87.4 to 87.7 mm (3.44 to 3.45 in.)
    No. 2 Race
    37.0 to 37.3 mm (1.46 to 1.47 in.)
    52.1 to 52.3 mm (2.05 to 2.06 in.)

  1. D028796E02
    Coat a new O-ring with ATF, and install it to the oil pump assembly.

  1. Place the oil pump through the input shaft, and align the bolt holes of the oil pump assembly with the transmission case.

  1. Hold the input shaft, and lightly press the oil pump body to slide the oil seal rings into the overdrive direct clutch drum.

    NOTICE:
    Do not excessively push on the oil pump, as the oil seal ring will stick to the direct clutch drum.

  1. D027921E01
    Install the 10 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


54. INSTALL MANUAL VALVE LEVER SHAFT OIL SEAL

  1. D028548E02
    Using SST and hammer, tap in 2 new oil seals.
    SST
    09350-30020   (09350-07110)

  1. Coat the lip of the oil seals with MP grease.


55. INSPECT INDIVIDUAL PISTON OPERATION

  1. D028547E02
    Check the operating sound while applying compressed air into the oil holes indicated in the illustration.

    HINT:
    When inspecting the O/D direct clutch, check with the accumulator piston holes indicated in the illustration.
    If there is no sound, disassemble and check the installation condition of the parts.

    1. No. 2 clutch (C2)
    2. No. 3 clutch (C3)
    3. No. 1 clutch (C1)
    4. No. 3 brake (B3)
    5. No. 1 brake (B1)
    6. No. 2 brake (B2)
    7. No. 4 brake (B4)


56. INSTALL MANUAL VALVE LEVER SUB-ASSEMBLY

  1. D028798E02
    Install a new spacer to the manual valve lever.

  1. Push the manual valve lever shaft through the transmission case, and install the manual valve lever to the manual valve lever shaft.

  1. D028799E01
    Using a hammer, tap in a new spring pin.

  1. D028800E01
    Align the manual valve lever indentation with the spacer hole, and stake them together with a punch.

  1. Check that the shaft rotates smoothly.


57. INSTALL PARKING LOCK PAWL SHAFT

  1. D028846E04
    Install the E-ring to the shaft.

  1. Install the parking lock pawl, shaft and spring.


58. INSTALL PARKING LOCK ROD SUB-ASSEMBLY

  1. D012709E01
    Connect the parking lock rod to the manual valve lever.


59. INSTALL PARKING LOCK PAWL BRACKET

  1. D012708E01
    Place the parking lock pawl bracket onto the transmission case and install the 3 bolts.

    Torque:
    7.4 N*m{ 75 kgf*cm , 65 in.*lbf }

  1. D028801E03
    Move the manual valve lever to the P position, and confirm that the planetary ring gear is correctly locked up by the lock pawl.


60. INSTALL C-1 ACCUMULATOR VALVE

  1. D028802E06
    Coat a new O-ring with ATF, and install it to the accumulator valve.

  1. D028803E01
    Install the spring and accumulator valve to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    C-1 Inner
    30.40 mm (1.20 in.)
    11.40 mm (0.449 in.)
    Pink
    C-1 Outer
    48.76 mm (1.92 in.)
    16.60 mm (0.654 in.)
    Light green


61. INSTALL C-3 ACCUMULATOR PISTON

  1. D028802E07
    Coat 2 new O-rings with ATF, and install them to the piston.

  1. D028804E01
    Install the 2 springs and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    C-3 Inner
    44.0 mm (1.73 in.)
    14.0 mm (0.551 in.)
    Yellow
    C-3 Outer
    73.35 mm (2.89 in.)
    19.90 mm (0.784 in.)
    Red


62. INSTALL B-3 ACCUMULATOR PISTON

  1. D028802E08
    Coat 2 new O-rings with ATF, and install them to the piston.

  1. D028805E01
    Install the spring and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    B-3
    70.5 mm (2.78 in.)
    19.7 mm (0.776 in.)
    Purple


63. INSTALL C-2 ACCUMULATOR PISTON

  1. D028802E09
    Coat 2 new O-rings with ATF, and install them to the piston.

  1. D028806E01
    Install the spring and accumulator piston to the hole.

    Accumulator Spring Diameter:
    Spring
    Free Length
    Outer Diameter
    Color
    C-2
    62.0 mm (2.44 in.)
    15.9 mm (0.626 in.)
    White


64. INSTALL CHECK BALL BODY

  1. D027914E05
    Install the spring and check ball body.


65. INSTALL BRAKE DRUM GASKET

  1. D027969E01
    Install the 3 brake drum gaskets.


66. INSTALL TRANSMISSION CASE GASKET

  1. D027968E08
    Install the 3 transmission case gaskets.


67. INSTALL TRANSMISSION VALVE BODY ASSEMBLY

  1. C157293E01
    Insert the pin of the manual valve into the hole of the manual valve lever.

  1. C157292E01
    Install the transmission valve body assembly with the 19 bolts.

    Torque:
    11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    36 mm (1.42 in.) for bolt A
    25 mm (0.984 in.) for bolt B

  1. Install the detent spring and detent spring cover with the bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


68. INSTALL TRANSMISSION WIRE

  1. D027912E01
    Install a new O-ring to the transmission wire.

  1. Install the transmission wire harness.

  1. Install the bolt.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. C125285E02
    Connect the 7 solenoid connectors.

  1. Install the 2 ATF temperature sensors.

  1. Install the 2 clamps and 2 bolts.

    Torque:
    for bolt A:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }
    for bolt B:
    11 N*m{ 112 kgf*cm , 8 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    12 mm (0.472 in.) for bolt A
    36 mm (1.42 in.) for bolt B

    Sensor Wire Harness: 
    Wire Harness
    Color
    No. 1 temperature sensor
    Orange
    No. 2 temperature sensor
    Blue


69. INSTALL VALVE BODY OIL STRAINER ASSEMBLY

  1. D012703E01
    Coat a new O-ring with ATF, and install it to the valve body oil strainer assembly.

  1. Install the oil strainer with the 4 bolts.

    Torque:
    10 N*m{ 100 kgf*cm , 7 ft.*lbf }


70. INSTALL TRANSMISSION OIL CLEANER MAGNET

  1. D027992E02
    Install the 4 magnets.


71. INSTALL AUTOMATIC TRANSMISSION OIL PAN SUB-ASSEMBLY
  1. Install a new gasket to the oil pan.

  1. Install the oil pan with the 20 bolts.

    Torque:
    4.4 N*m{ 45 kgf*cm , 39 in.*lbf }

  1. Install the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


72. INSTALL TRANSFER CASE ADAPTER RADIAL BALL BEARING

C162768E01
  1. Using SST and a press, press in the bearing until it stops.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)

  1. Using a screwdriver, install the snap ring.


73. INSTALL TRANSMISSION CASE ADAPTER REAR OIL SEAL

C177436E01
  1. Coat the lip of a new oil seal with ATF.

  1. Using SST and a hammer, tap in the oil seal.

    SST
    09950-60010   (09951-00650)
    09950-70010   (09951-07150)

    Standard depth:
    0 to 0.5 mm (0 to 0.0197 in.)


74. INSTALL TRANSFER ADAPTER REAR
  1. Clean the threads of the bolts and case.

  1. C175554E01
    Apply seal packing or equivalent to the transmission case adapter and 8 bolts.

    Seal packing:
    Toyota Genuine Seal Packing 1281,
    Three Bond 1281 or equivalent

    Seal diameter:
    1.0 to 1.5 mm (0.0394 to 0.0591 in.)

  1. C175553E02
    Install the transmission case adapter with the 8 bolts.

    Torque:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }

    HINT:
    Each bolt length is indicated below.
    50 mm (1.97 in.) for bolt A
    45 mm (1.77 in.) for bolt B


75. INSTALL AUTOMATIC TRANSMISSION HOUSING

C158385E03
  1. Clean the threads of the bolts and case with non-residue solvent.

  1. Install the transmission housing with the 10 bolts.

    Torque:
    for 14 mm head bolt A:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }
    for 17 mm head bolt B:
    57 N*m{ 581 kgf*cm , 42 ft.*lbf }
    for 14 mm head bolt C:
    34 N*m{ 345 kgf*cm , 25 ft.*lbf }


76. INSTALL AUTOMATIC TRANSMISSION BREATHER TUBE

C117463E01
  1. Coat a new O-ring with ATF and install it to the breather tube.

  1. Install the breather tube with the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


77. INSTALL SPEED SENSOR

  1. C111258
    Coat 2 new O-rings with ATF, and install them to the speed sensors.

  1. Install the 2 speed sensors.

  1. Install the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


78. INSTALL OIL COOLER TUBE UNION
  1. Coat 2 new O-rings with ATF, and install them to the 2 oil cooler tube unions.

  1. C250978
    Using a union nut wrench, install the 2 oil cooler tube unions.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).


79. INSTALL PARK/NEUTRAL POSITION SWITCH ASSEMBLY

D027903E01
  1. Install the park/neutral position switch to the manual valve lever shaft, and temporarily install the adjusting bolt.

  1. Install a new lock washer and the nut.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }

  1. C172409E01
    Push the control shaft rearward as much as possible.

  1. Return the control shaft lever 2 notches to the N position.

  1. D025795E10
    Align the neutral basic line with the switch groove as shown in the illustration, and tighten the adjusting bolt.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. D027990E01
    Using a screwdriver, bend the tabs of the lock washer.

    HINT:
    Bend at least 2 of the lock washer tabs.


80. INSTALL TRANSMISSION CONTROL SHAFT LEVER RH

  1. C170829
    Install the control shaft lever with the washer and nut.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }

← INSPECTION (from Jan 2012)REASSEMBLY (from Jan 2012) →