TERMINALS OF ECM
System information · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


Measure the voltage according to the value(s) in the table below.
- HINT:
- The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.
- The result of the checks should be compared with the standard normal voltage for that pair of terminals, which is displayed in the Specified Condition column.
- The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| A38*1-20 (BATT) - C45*1-81 (E1) A52*2-20 (BATT) - C46*2-81 (E1) |
L - BR |
Battery (for measuring the battery voltage and for the ECM memory) |
Always |
11 to 14 V |
| A38*1-28 (IGSW) - C45*1-81 (E1) A52*2-28 (IGSW) - C46*2-81 (E1) |
B - BR |
Ignition switch |
Ignition switch ON |
11 to 14 V |
| A38*1-2 (+B) - C45*1-81 (E1) A52*2-2 (+B) - C46*2-81 (E1) |
B - BR |
Power source of ECM |
Ignition switch ON |
11 to 14 V |
| A38*1-44 (MREL) - C45*1-81 (E1) A52*2-44 (MREL) - C46*2-81 (E1) |
W-R - BR |
EFI relay |
Ignition switch ON |
11 to 14 V |
| 10 seconds elapsed after ignition switch turned off |
0 to 1.5 V |
|||
| C45*1-66 (VCPM) - C45*1-75 (E2) C46*2-66 (VCPM) - C46*2-75 (E2) |
L-B - BR |
Power source of manifold absolute pressure sensor (for PIM) |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-70 (VCM) - C45*1-75 (E2) C46*2-70 (VCM) - C46*2-75 (E2) |
L-R - BR |
Power source of fuel pressure sensor (for PCR1) |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-90 (VCEG) - C45*1-87 (EEGL) C46*2-90 (VCEG) - C46*2-87 (EEGL) |
L-R - BR |
Power source of EGR valve position sensor |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-91 (VCVL) - C45*1-92 (EVLU) C46*2-91 (VCVL) - C46*2-92 (EVLU) |
L-R - BR |
Power source of throttle position sensor |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-72 (VG) - C45*1-118 (EVG) C46*2-72 (VG) - C46*2-118 (EVG) |
L-Y - G-W |
Mass air flow meter |
Engine warmed up and idling, A/C switch off |
0.5 to 3.4 V |
| C45*1-71 (THA) - C45*1-75 (E2) C46*2-71 (THA) - C46*2-75 (E2) |
Y - BR |
Intake air temperature sensor (built into mass air flow meter) |
Engine warmed up and idling, intake air temperature at 0 to 80°C (32 to 176°F) |
0.5 to 3.4 V |
| A38*1-53 (VPA) - A38*1-57 (EPA) A52*2-53 (VPA) - A52*2-57 (EPA) |
R - W-L |
Accelerator pedal position sensor (for engine control) |
Ignition switch ON, accelerator pedal fully released |
0.6 to 1.0 V |
| Ignition switch ON, accelerator pedal fully depressed |
3.0 to 4.6 V |
|||
| A38*1-54 (VPA2) - A38*1-58 (EPA2) A52*2-54 (VPA2) - A52*2-58 (EPA2) |
GR-G - BR |
Accelerator pedal position sensor (for sensor malfunction detection) |
Ignition switch ON, accelerator pedal fully released |
1.4 to 1.8 V |
| Ignition switch ON, accelerator pedal fully depressed |
3.7 to 5.0 V |
|||
| A38*1-55 (VCPA) - A38*1-57 (EPA) A52*2-55 (VCPA) - A52*2-57 (EPA) |
L-W - W-L |
Power source of accelerator pedal position sensor (for VPA) |
Ignition switch ON |
4.5 to 5.5 V |
| A38*1-56 (VCP2) - A38*1-58 (EPA2) A52*2-56 (VCP2) - A52*2-58 (EPA2) |
V - BR |
Power source of accelerator pedal position sensor (for VPA2) |
Ignition switch ON |
4.5 to 5.5 V |
| C45*1-74 (THIA) - C45*1-75 (E2) C46*2-74 (THIA) - C46*2-75 (E2) |
W-G - BR |
Intake air temperature sensor (after turbocharged) |
Engine warmed up and idling, intake air temperature sensor (after turbocharged) at 0 to 80°C (32 to 176°F) |
0.5 to 3.4 V |
| C45*1-76 (THW) - C45*1-75 (E2) C46*2-76 (THW) - C46*2-75 (E2) |
G-B - BR |
Engine coolant temperature sensor |
Engine warmed up and idling, engine coolant temperature at 60 to 120°C (140 to 248°F) |
0.2 to 1.2 V |
| C45*1-40 (#1) - C45*1-81 (E1) |
Y - BR |
Fuel injector |
Idling |
Pulse generation (see waveform 1) |
| C46*2-40 (#1) - C46*2-81 (E1) | ||||
| C45*1-39 (#2) - C45*1-81 (E1) |
B - BR |
|||
| C46*2-39 (#2) - C46*2-81 (E1) | ||||
| C45*1-38 (#3) - C45*1-81 (E1) |
L - BR |
|||
| C46*2-38 (#3) - C46*2-81 (E1) | ||||
| C45*1-37 (#4) - C45*1-81 (E1) |
R - BR |
|||
| C46*2-37 (#4) - C46*2-81 (E1) | ||||
| C45*1-36 (#5) - C45*1-81 (E1) |
G - BR |
|||
| C46*2-36 (#5) - C46*2-81 (E1) | ||||
| C45*1-35 (#6) - C45*1-81 (E1) |
V - BR |
|||
| C46*2-35 (#6) - C46*2-81 (E1) | ||||
| C45*1-34 (#7) - C45*1-81 (E1) |
W - BR |
|||
| C46*2-34 (#7) - C46*2-81 (E1) | ||||
| C45*1-33 (#8) - C45*1-81 (E1) |
P - BR |
|||
| C46*2-33 (#8) - C46*2-81 (E1) | ||||
| C45*1-80 (G+) - C45*1-79 (G-) C46*2-80 (G+) - C46*2-79 (G-) |
W - B |
Camshaft position sensor |
Idling |
Pulse generation (see waveform) |
| C45*1-78 (NE+) - C45*1-77 (NE-) C46*2-78 (NE+) - C46*2-77 (NE-) |
B - W |
Crankshaft position sensor |
Idling |
Pulse generation (see waveform) |
| C45*1-114 (PIM) - C45*1-75 (E2) C46*2-114 (PIM) - C46*2-75 (E2) |
P-L - BR |
Manifold absolute pressure sensor |
Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied |
0.1 to 0.7 V |
| Same as atmospheric pressure |
0.8 to 1.4 V |
|||
| Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied |
1.6 to 2.2 V |
|||
| A38*1-45 (IREL) - C45*1-81 (E1) A52*2-45 (IREL) - C46*2-81 (E1) |
P-L - BR |
EDU relay (EDU 1) |
Ignition switch off |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| A38*1-46 (IRL2) - C45*1-81 (E1) A52*2-46 (IRL2) - C46*2-81 (E1) |
P-B - BR |
EDU relay (EDU 2) |
Ignition switch off |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| C45*1-69 (PCR1) - C45*1-75 (E2) C46*2-69 (PCR1) - C46*2-75 (E2) |
B - BR |
Fuel pressure sensor |
Idling (Approximately 35 MPa (357 kgf/cm2, 5078 psi)) |
1.3 to 1.8 V |
| C45*1-63 (GREL) - C45*1-81 (E1) C46*2-63 (GREL) - C46*2-81 (E1) |
R-B - BR |
No. 1 glow relay |
Cranking |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| C45*1-62 (GRL2) - C45*1-81 (E1) C46*2-62 (GRL2) - C46*2-81 (E1) |
R - BR |
No. 2 glow relay |
Cranking |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| C45*1-116 (THF) - C45*1-75 (E2) C46*2-116 (THF) - C46*2-75 (E2) |
G-R - BR |
Fuel temperature sensor |
Ignition switch ON |
0.5 to 3.4 V |
| C45*1-106 (PCV+) - C45*1-105 (PCV-) C46*2-106 (PCV+) - C46*2-105 (PCV-) |
W - BR |
Suction control valve |
Idling |
Pulse generation (see waveform 2) |
| C45*1-61 (INJF) - C45*1-81 (E1) C46*2-61 (INJF) - C46*2-81 (E1) |
G - BR |
No. 1 injector driver |
Idling |
Pulse generation (see waveform 3) |
| C45*1-60 (INF2) - C45*1-81 (E1) C46*2-60 (INF2) - C46*2-81 (E1) |
W - BR |
No. 2 injector driver |
Idling |
Pulse generation (see waveform 3) |
| C45*1-93 (VLU) - C45*1-75 (E2) C46*2-93 (VLU) - C46*2-75 (E2) |
L-W - BR |
Throttle position sensor (for Bank 1) |
Ignition switch ON (throttle valve fully opened) |
2.8 to 3.8 V |
| Idling (throttle valve fully closed) |
0.4 to 1.0 V |
|||
| C45*1-103 (VLU2) - C45*1-75 (E2) C46*2-103 (VLU2) - C46*2-75 (E2) |
L-W - BR |
Throttle position sensor (for Bank 2) |
Ignition switch ON (throttle valve fully opened) |
2.8 to 3.8 V |
| Idling (throttle valve fully closed) |
0.4 to 1.0 V |
|||
| C45*1-42 (LUSL) - C45*1-81 (E1) C46*2-42 (LUSL) - C46*2-81 (E1) |
B - BR |
Diesel throttle duty signal (for Bank 1) |
Engine warmed up, racing engine |
Pulse generation (see waveform 4) |
| C45*1-84 (LUS2) - C45*1-81 (E1) C46*2-84 (LUS2) - C46*2-81 (E1) |
B - BR |
Diesel throttle duty signal (for Bank 2) |
Engine warmed up, racing engine |
Pulse generation (see waveform 4) |
| C45*1-89 (EGLS) - C45*1-75 (E2) C46*2-89 (EGLS) - C46*2-75 (E2) |
R-W - BR |
No. 1 EGR valve position sensor |
Ignition switch ON |
3.0 to 4.6 V |
| C45*1-88 (EGS2) - C45*1-75 (E2) C46*2-88 (EGS2) - C46*2-75 (E2) |
R-B - BR |
No. 2 EGR valve position sensor |
Ignition switch ON |
3.0 to 4.6 V |
| C45*1-107 (EGRS) - C45*1-81 (E1) C46*2-107 (EGRS) - C46*2-81 (E1) |
R - BR |
No. 1 EGR valve |
Engine warmed up and idling |
Pulse generation (see waveform 5) |
| C45*1-108 (ERS2) - C45*1-81 (E1) C46*2-108 (ERS2) - C46*2-81 (E1) |
R-W - BR |
No. 2 EGR valve |
Engine warmed up and idling |
Pulse generation (see waveform 5) |
| C45*1-49 (VNTO) - C45*1-81 (E1) C46*2-49 (VNTO) - C46*2-81 (E1) |
R-Y - BR |
Turbo motor driver (for Bank 1) |
Idling |
Pulse generation (see waveform 6) |
| C45*1-47 (VNO2) - C45*1-81 (E1) C46*2-47 (VNO2) - C46*2-81 (E1) |
R-W - BR |
Turbo motor driver (for Bank 2) |
Idling |
Pulse generation (see waveform 6) |
| C45*1-50 (VNTI) - C45*1-81 (E1) C46*2-50 (VNTI) - C46*2-81 (E1) |
R-L - BR |
Turbo motor driver (for Bank 1) |
Idling |
Pulse generation (see waveform 7) |
| C45*1-48 (VNI2) - C45*1-81 (E1) C46*2-48 (VNI2) - C46*2-81 (E1) |
BR - BR |
Turbo motor driver (for Bank 2) |
Idling |
Pulse generation (see waveform 7) |
| A38*1-36 (STP) - C45*1-81 (E1) A52*2-36 (STP) - C46*2-81 (E1) |
R - BR |
Stop light switch |
Ignition switch ON, brake pedal depressed |
7.5 to 14 V |
| Ignition switch ON, brake pedal released |
0 to 1.5 V |
|||
| A38*1-35 (ST1-) - C45*1-81 (E1) A52*2-35 (ST1-) - C46*2-81 (E1) |
R-W - BR |
Stop light switch (opposite to STP) |
Ignition switch ON, brake pedal depressed |
0 to 1.5 V |
| Ignition switch ON, brake pedal released |
7.5 to 14 V |
|||
| A38*1-15 (TACH) - C45*1-81 (E1) A52*2-15 (TACH) - C46*2-81 (E1) |
W-G - BR |
Engine speed |
Idling |
Pulse generation (see waveform 8) |
| A38*1-8 (SPD) - C45*1-81 (E1) A52*2-8 (SPD) - C46*2-81 (E1) |
V-R - BR |
Speed signal from combination meter |
Ignition switch ON, wheel rotated slowly |
Pulse generation (see waveform 9) |
| A38*1-48 (STA) - C45*1-81 (E1) A52*2-48 (STA) - C46*2-81 (E1) |
R-B - BR |
Starter signal |
Cranking |
6.0 V or more |
| C45*1-1 (ALT) - C45*1-81 (E1) C46*2-1 (ALT) - C46*2-81 (E1) |
R - BR |
Generator duty ratio |
Idling |
Pulse generation |
| A38*1-27 (TC) - C45*1-81 (E1) A52*2-27 (TC) - C46*2-81 (E1) |
V-W - BR |
Terminal TC of DLC3 |
Ignition switch ON |
11 to 14 V |
| A38*1-24 (W) - C45*1-81 (E1) A52*2-24 (W) - C46*2-81 (E1) |
R-Y - BR |
MIL |
MIL illuminated |
0 to 3 V |
| MIL not illuminated |
11 to 14 V |
|||
| A38*1-30 (AC1) - C45*1-81 (E1) A52*2-30 (AC1) - C46*2-81 (E1) |
L-O - BR |
A/C signal |
A/C switch on |
0 to 1.5 V |
| A/C switch off |
11 to 14 V |
|||
| A38*1-18 (ACT) - C45*1-81 (E1) A52*2-18 (ACT) - C46*2-81 (E1) |
G-R - BR |
A/C signal |
Ignition switch ON |
11 to 14 V |
| A/C cut control on |
0 to 3 V |
|||
| A38*1-42 (CLSW) - C45*1-81 (E1) A52*2-42 (CLSW) - C46*2-81 (E1) |
G-B - BR |
Clutch start switch |
Ignition switch ON, clutch pedal fully depressed |
0 to 3 V |
| Ignition switch ON, clutch pedal fully released |
11 to 14 V |
|||
| C45*1-2 (PS) - C45*1-81 (E1) C46*2-2 (PS) - C46*2-81 (E1) |
P - BR |
Power steering oil pressure switch |
Steering wheel turned |
0 to 3 V |
| Steering wheel not turned |
11 to 14 V |
|||
| C45*1-32 (FSW) - C45*1-81 (E1) C46*2-32 (FSW) - C46*2-81 (E1) |
L*3 - BR |
Shift position switch |
Ignition switch ON, shift lever in 1 |
11 to 14 V |
| Ignition switch ON, shift lever not in 1 |
0 to 3 V |
|||
| C45*1-45 (ACM) - C45*1-81 (E1) C46*2-45 (ACM) - C46*2-81 (E1) |
L - BR |
VSV (for engine mounting) |
Idling |
0 to 1.5 V |
| A38*1-43 (NSW) - C45*1-81 (E1) A52*2-43 (NSW) - C46*2-81 (E1) |
L - BR |
Park/neutral position switch |
Ignition switch ON, shift lever in P or N |
Below 3 V |
| Ignition switch ON, shift lever not in P and N |
11 to 14 V |
|||
| A38*1-41 (CANH) - C45*1-81 (E1) A52*2-41 (CANH) - C46*2-81 (E1) |
P - BR |
CAN communication line |
Ignition switch ON |
Pulse generation) (see waveform 10) |
| A38*1-49 (CANL) - C45*1-81 (E1) A52*2-49 (CANL) - C46*2-81 (E1) |
B - BR |
CAN communication line |
Ignition switch ON |
Pulse generation) (see waveform 11) |
| A38*1-14 (STSW) - C45*1-81 (E1) A52*2-14 (STSW) - C46*2-81 (E1) |
R - BR |
Ignition switch signal |
Shift lever in P or N, ignition switch pushed |
6.0 V or more |
| A38*1-13 (ACCR) - C45*1-81 (E1) A52*1-13 (ACCR) - C45*1-81 (E1) |
L-Y - BR |
ACC (Accessory) relay control signal |
Cranking |
Below 1.5 V |
| C45*1-51 (STAR) - C45*1-81 (E1) C46*2-51 (STAR) - C46*2-81 (E1) |
L - BR |
Starter relay control |
Ignition switch ON |
Below 1.5 V |
| Cranking |
6.0 V or more |
|||
| C45*1-43 (FC) - C45*1-81 (E1) C46*2-43 (FC) - C46*2-81 (E1) |
L-B - BR |
Sub pump relay |
Relay on |
0 to 1.5 V |
| Relay off |
7.5 to 14 V |
- HINT:
- *1: for LHD
- *2: for RHD
- *3: for M/T
- *1: for LHD
| WAVEFORM 1 |
![]() ![]() |
| ECM Terminal Name |
From #1 to #8 and E1 |
| Tester Range |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the injector injection.
| WAVEFORM 2 |
![]() ![]() |
| ECM Terminal Name |
PCV+ and PCV- |
| Tester Range |
10 V/DIV., 5 msec./DIV. |
| Condition |
Idling or cranking with warm engine |
- HINT:
- The waveform varies depending on the suction control valve operation.
| WAVEFORM 3 |
![]() ![]() |
| ECM Terminal Name |
INJF and E1 INF2 and E1 |
| Tester Range |
2 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the injector injection.
| WAVEFORM 4 |
![]() ![]() |
| ECM Terminal Name |
LUSL and E1 LUS2 and E1 |
| Tester Range |
1 V/DIV., 2 msec./DIV. |
| Condition |
Racing with warm engine |
- HINT:
- The waveform varies depending on the throttle valve operation.
| WAVEFORM 5 |
![]() ![]() |
| ECM Terminal Name |
EGRS and E1 ERS2 and E1 |
| Tester Range |
5 V/DIV., 5 msec./DIV. |
| Condition |
Idling |
- HINT:
- The waveform varies depending on the throttle valve operation.
| WAVEFORM 6 |
![]() ![]() |
| ECM Terminal Name |
VNTO and E1 VNO2 and E1 |
| Tester Range |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the turbocharger operation.
| WAVEFORM 7 |
![]() ![]() |
| ECM Terminal Name |
VNTI and E1 VNI2 and E1 |
| Tester Range |
5 V/DIV., 50 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the turbocharger status.
| WAVEFORM 8 |
![]() ![]() |
| ECM Terminal Names |
TACH and E1 |
| Tester Range |
5 V/DIV., 10 msec./DIV. |
| Conditions |
Idling |
- HINT:
- The wavelength becomes shorter as the engine speed increases.
| WAVEFORM 9 |
![]() ![]() |
| ECM Terminal Name |
SPD and E1 |
| Tester Range |
5 V/DIV., 10 msec./DIV. |
| Condition |
Driving at vehicle speed of 40 km/h (25 mph) |
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| WAVEFORM 10 |
![]() ![]() |
| ECM Terminal Name |
CAN+ and E1 |
| Tester Range |
1 V/DIV., 10 msec./DIV. |
| Condition |
Engine stopped, ignition switch ON |
- HINT:
- The waveform varies depending on the CAN communication signal.
| WAVEFORM 11 |
![]() ![]() |
| ECM Terminal Name |
CAN- and E1 |
| Tester Range |
1 V/DIV., 10 msec./DIV. |
| Condition |
Engine stopped, ignition switch ON |
- HINT:
- The waveform varies depending on the CAN communication signal.










