TERMINALS OF ECM
System information · Vehicles built from Jan 2012


Measure the voltage according to the value(s) in the table below.
- HINT:
- The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated.
- The result of the checks should be compared with the standard normal voltage for that pair of terminals, which is displayed in the Specified Condition column.
- The illustration above can be used as a reference to identify the ECM terminal locations.
| Terminal No. (Symbol) |
Wiring Color |
Terminal Description |
Condition |
Specified Condition |
| A38*1-20 (BATT) - C45*1-81 (E1) A52*2-20 (BATT) - C46*2-81 (E1) |
L - BR |
Battery (for measuring the battery voltage and for the ECM memory) |
Always |
11 to 14 V |
| A38*1-28 (IGSW) - C45*1-81 (E1) A52*2-28 (IGSW) - C46*2-81 (E1) |
B - BR |
Engine switch |
Engine switch on (IG) |
11 to 14 V |
| A38*1-2 (+B) - C45*1-81 (E1) A52*2-2 (+B) - C46*2-81 (E1) |
B - BR |
Power source of ECM |
Engine switch on (IG) |
11 to 14 V |
| A38*1-1 (+B2) - C45*1-81 (E1) A52*2-1 (+B2) - C46*2-81 (E1) |
B - BR |
Power source of ECM |
Engine switch on (IG) |
11 to 14 V |
| A38*1-44 (MREL) - C45*1-81 (E1) A52*2-44 (MREL) - C46*2-81 (E1) |
W - BR |
EFI relay |
Engine switch on (IG) |
11 to 14 V |
| 10 seconds elapsed after engine switch turned off |
0 to 1.5 V |
|||
| C45*1-66 (VCPM) - C45*1-92 (E2) C46*2-66 (VCPM) - C46*2-92 (E2) |
L-B - BR |
Power source of manifold absolute pressure sensor (for PIM) |
Engine switch on (IG) |
4.5 to 5.5 V |
| C45*1-118 (VCM) - C45*1-95 (E2M) C46*2-118 (VCM) - C46*2-95 (E2M) |
L-R - BR |
Power source of fuel pressure sensor (for PCR1) |
Engine switch on (IG) |
4.5 to 5.5 V |
| C45*1-91 (VC) - C45*1-92 (E2) C46*2-91 (VC) - C46*2-92 (E2) |
B - BR |
Power source of EGR valve position sensor and differential pressure sensor |
Engine switch on (IG) |
4.5 to 5.5 V |
| C45*1-110 (VCVL) - C45*1-87 (EVLU) C46*2-110 (VCVL) - C46*2-87 (EVLU) |
L-R - BR |
Power source of throttle position sensor |
Engine switch on (IG) |
4.5 to 5.5 V |
| C45*1-71 (VG) - C45*1-94 (EVG) C46*2-71 (VG) - C46*2-94 (EVG) |
L-Y - G-W |
Mass air flow meter |
Idling |
Pulse generation |
| C45*1-115 (THA) - C45*1-92 (E2) C46*2-115 (THA) - C46*2-92 (E2) |
Y - BR |
Intake air temperature sensor (built into mass air flow meter) |
Engine warmed up and idling, intake air temperature at 0 to 80°C (32 to 176°F) |
0.5 to 3.4 V |
| A38*1-53 (VPA) - A38*1-57 (EPA) A52*2-53 (VPA) - A52*2-57 (EPA) |
R - W-L |
Accelerator pedal position sensor (for engine control) |
Engine switch on (IG), accelerator pedal fully released |
0.6 to 1.0 V |
| Engine switch on (IG), accelerator pedal fully depressed |
3.0 to 4.6 V |
|||
| A38*1-54 (VPA2) - A38*1-58 (EPA2) A52*2-54 (VPA2) - A52*2-58 (EPA2) |
GR-G - BR |
Accelerator pedal position sensor (for sensor malfunction detection) |
Engine switch on (IG), accelerator pedal fully released |
1.4 to 1.8 V |
| Engine switch on (IG), accelerator pedal fully depressed |
3.7 to 5.0 V |
|||
| A38*1-55 (VCPA) - A38*1-57 (EPA) A52*2-55 (VCPA) - A52*2-57 (EPA) |
L-W - W-L |
Power source of accelerator pedal position sensor (for VPA) |
Engine switch on (IG) |
4.5 to 5.5 V |
| A38*1-56 (VCP2) - A38*1-58 (EPA2) A52*2-56 (VCP2) - A52*2-58 (EPA2) |
V - BR |
Power source of accelerator pedal position sensor (for VPA2) |
Engine switch on (IG) |
4.5 to 5.5 V |
| C45*1-90 (THIA) - C45*1-92 (E2) C46*2-90 (THIA) - C46*2-92 (E2) |
W-G - BR |
Intake air temperature sensor (turbo) |
Engine warmed up and idling, intake air temperature sensor (after turbocharged) at 0 to 80°C (32 to 176°F) |
0.5 to 3.4 V |
| C45*1-93 (THW) - C45*1-92 (E2) C46*2-93 (THW) - C46*2-92 (E2) |
G-B - BR |
Engine coolant temperature sensor |
Engine warmed up and idling, engine coolant temperature at 60 to 120°C (140 to 248°F) |
0.2 to 1.2 V |
| C45*1-40 (#1) - C45*1-81 (E1) C46*2-40 (#1) - C46*2-81 (E1) |
Y - BR |
Injector assembly |
Idling |
Pulse generation (see waveform 1) |
| C45*1-39 (#2) - C45*1-81 (E1) C46*2-39 (#2) - C46*2-81 (E1) |
B - BR |
|||
| C45*1-38 (#3) - C45*1-81 (E1) C46*2-38 (#3) - C46*2-81 (E1) |
L - BR |
|||
| C45*1-37 (#4) - C45*1-81 (E1) C46*2-37 (#4) - C46*2-81 (E1) |
R - BR |
|||
| C45*1-36 (#5) - C45*1-81 (E1) C46*2-36 (#5) - C46*2-81 (E1) |
G - BR |
|||
| C45*1-35 (#6) - C45*1-81 (E1) C46*2-35 (#6) - C46*2-81 (E1) |
V - BR |
|||
| C45*1-34 (#7) - C45*1-81 (E1) C46*2-34 (#7) - C46*2-81 (E1) |
W - BR |
|||
| C45*1-33 (#8) - C45*1-81 (E1) C46*2-33 (#8) - C46*2-81 (E1) |
P - BR |
|||
| C45*1-80 (G+) - C45*1-79 (G-) C46*2-80 (G+) - C46*2-79 (G-) |
W - B |
Camshaft position sensor |
Idling |
Pulse generation |
| C45*1-78 (NE+) - C45*1-77 (NE-) C46*2-78 (NE+) - C46*2-77 (NE-) |
B - W |
Crankshaft position sensor |
Idling |
Pulse generation |
| C45*1-67 (PIM) - C45*1-92 (E2) C46*2-67 (PIM) - C46*2-92 (E2) |
P-L - BR |
Manifold absolute pressure sensor |
Negative pressure of 40 kPa (300 mmHg, 11.8 in.Hg) applied |
0.1 to 0.7 V |
| Same as atmospheric pressure |
0.8 to 1.4 V |
|||
| Positive pressure of 170 kPa (1275 mmHg, 50.2 in.Hg) applied |
1.6 to 2.2 V |
|||
| A38*1-45 (IREL) - C45*1-81 (E1) A52*2-45 (IREL) - C46*2-81 (E1) |
P-L - BR |
EDU relay (EDU 1) |
Engine switch off |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| A38*1-46 (IRL2) - C45*1-81 (E1) A52*2-46 (IRL2) - C46*2-81 (E1) |
P-B - BR |
EDU relay (EDU 2) |
Engine switch off |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| C45*1-72 (PCR1) - C45*1-95 (E2M) C46*2-72 (PCR1) - C46*2-95 (E2M) |
B - BR |
Fuel pressure sensor |
Idling (Approximately 35 MPa (357 kgf/cm2, 5078 psi)) |
1.3 to 1.8 V |
| A38*1-12 (GREL) - C45*1-81 (E1) A52*2-12 (GREL) - C46*2-81 (E1) |
R-W - BR |
No. 1 glow relay |
Cranking |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| A38*1-23 (GRL2) - C45*1-81 (E1) A52*2-23 (GRL2) - C46*2-81 (E1) |
LG - BR |
No. 2 glow relay |
Cranking |
11 to 14 V |
| Idling |
0 to 1.5 V |
|||
| C45*1-116 (THF) - C45*1-92 (E2) C46*2-116 (THF) - C46*2-92 (E2) |
G-R - BR |
Fuel temperature sensor |
Engine switch on (IG) |
0.5 to 3.4 V |
| C45*1-104 (PCV+) - C45*1-105 (PCV-) C46*2-104 (PCV+) - C46*2-105 (PCV-) |
W - BR |
Suction control valve |
Idling |
Pulse generation (see waveform 2) |
| C45*1-61 (INJ1) - C45*1-81 (E1) C46*2-61 (INJ1) - C46*2-81 (E1) |
G - BR |
No. 1 injector driver |
Idling |
Pulse generation (see waveform 3) |
| C45*1-60 (INJ2) - C45*1-81 (E1) C46*2-60 (INJ2) - C46*2-81 (E1) |
W - BR |
No. 2 injector driver |
Idling |
Pulse generation (see waveform 3) |
| C45*1-64 (VLU) - C45*1-87 (EVLU) C46*2-64 (VLU) - C46*2-87 (EVLU) |
L-W - BR |
Throttle position sensor (for Bank 1) |
Engine switch on (IG) (throttle valve fully opened) |
2.8 to 3.8 V |
| Idling (throttle valve fully closed) |
0.4 to 1.0 V |
|||
| C45*1-65 (VLU2) - C45*1-87 (EVLU) C46*2-65 (VLU2) - C46*2-87 (EVLU) |
L-W - BR |
Throttle position sensor (for Bank 2) |
Engine switch on (IG) (throttle valve fully opened) |
2.8 to 3.8 V |
| Idling (throttle valve fully closed) |
0.4 to 1.0 V |
|||
| C45*1-57 (LUSL) - C45*1-81 (E1) C46*2-57 (LUSL) - C46*2-81 (E1) |
B - BR |
Diesel throttle duty signal (for Bank 1) |
Engine warmed up, racing engine |
Pulse generation (see waveform 4) |
| C45*1-56 (LUS2) - C45*1-81 (E1) C46*2-56 (LUS2) - C46*2-81 (E1) |
B - BR |
Diesel throttle duty signal (for Bank 2) |
Engine warmed up, racing engine |
Pulse generation (see waveform 4) |
| C45*1-88 (EGLS) - C45*1-92 (E2) C46*2-88 (EGLS) - C46*2-92 (E2) |
R-W - BR |
No. 1 EGR valve position sensor |
Engine switch on (IG) |
3.0 to 4.6 V |
| C45*1-89 (EGS2) - C45*1-92 (E2) C46*2-89 (EGS2) - C46*2-92 (E2) |
R-B - BR |
No. 2 EGR valve position sensor |
Engine switch on (IG) |
3.0 to 4.6 V |
| C45*1-82 (EGRS) - C45*1-81 (E1) C46*2-82 (EGRS) - C46*2-81 (E1) |
R - BR |
No. 1 EGR valve assembly |
Engine warmed up and idling |
Pulse generation (see waveform 5) |
| C45*1-42 (ERS2) - C45*1-81 (E1) C46*2-42 (ERS2) - C46*2-81 (E1) |
R-W - BR |
No. 2 EGR valve assembly |
Engine warmed up and idling |
Pulse generation (see waveform 5) |
| C45*1-86 (M+) - C45*1-81 (E1) C46*2-86 (M+) - C46*2-81 (E1) |
G - BR |
DC motor (turbocharger sub-assembly for Bank 1) |
Idling |
Pulse generation (see waveform 6) |
| C45*1-18 (VN2+) - C45*1-81 (E1) C46*2-18 (VN2+) - C46*2-81 (E1) |
W - BR |
DC motor (turbocharger sub-assembly for Bank 2) |
Idling |
Pulse generation (see waveform 6) |
| C45*1-85 (M-) - C45*1-81 (E1) C46*2-85 (M-) - C46*2-81 (E1) |
B - BR |
DC motor (turbocharger sub-assembly for Bank 1) |
Idling |
Pulse generation (see waveform 7) |
| C45*1-41 (VN2-) - C45*1-81 (E1) C46*2-41 (VN2-) - C46*2-81 (E1) |
B - BR |
DC motor (turbocharger sub-assembly for Bank 2) |
Idling |
Pulse generation (see waveform 7) |
| A38*1-13 (STP) - C45*1-81 (E1) A52*2-13 (STP) - C46*2-81 (E1) |
R - BR |
Stop light switch |
Engine switch on (IG), brake pedal depressed |
7.5 to 14 V |
| Engine switch on (IG), brake pedal released |
0 to 1.5 V |
|||
| A38*1-35 (ST1-) - C45*1-81 (E1) A52*2-35 (ST1-) - C46*2-81 (E1) |
R-W - BR |
Stop light switch (opposite to STP) |
Engine switch on (IG), brake pedal depressed |
0 to 1.5 V |
| Engine switch on (IG), brake pedal released |
7.5 to 14 V |
|||
| A38*1-15 (TACH) - C45*1-81 (E1) A52*2-15 (TACH) - C46*2-81 (E1) |
W-G - BR |
Engine speed |
Idling |
Pulse generation (see waveform 8) |
| A38*1-8 (SPD) - C45*1-81 (E1) A52*2-8 (SPD) - C46*2-81 (E1) |
V-R - BR |
Speed signal from combination meter |
Engine switch on (IG), wheel rotated slowly |
Pulse generation (see waveform 9) |
| A38*1-48 (STA) - C45*1-81 (E1) A52*2-48 (STA) - C46*2-81 (E1) |
R-B - BR |
Starter signal |
Cranking |
6.0 V or more |
| C45*1-53 (ALT) - C45*1-81 (E1) C46*2-53 (ALT) - C46*2-81 (E1) |
R - BR |
Generator duty ratio |
Idling |
Pulse generation |
| A38*1-27 (TC) - C45*1-81 (E1) A52*2-27 (TC) - C46*2-81 (E1) |
V-W - BR |
Terminal TC of DLC3 |
Engine switch on (IG) |
11 to 14 V |
| A38*1-24 (W) - C45*1-81 (E1) A52*2-24 (W) - C46*2-81 (E1) |
R-Y - BR |
MIL |
MIL illuminated |
0 to 3 V |
| MIL not illuminated |
11 to 14 V |
|||
| A38*1-30 (AC1) - C45*1-81 (E1) A52*2-30 (AC1) - C46*2-81 (E1) |
L-O - BR |
A/C signal |
A/C switch on |
0 to 1.5 V |
| A/C switch off |
11 to 14 V |
|||
| A38*1-18 (ACT) - C45*1-81 (E1) A52*2-18 (ACT) - C46*2-81 (E1) |
G-R - BR |
A/C signal |
Engine switch on (IG) |
11 to 14 V |
| A/C cut control on |
0 to 3 V |
|||
| C45*1-55 (PSW) - C45*1-81 (E1) C46*2-55 (PSW) - C46*2-81 (E1) |
P - BR |
Power steering oil pressure switch |
Steering wheel turned |
0 to 3 V |
| Steering wheel not turned |
11 to 14 V |
|||
| A38*1-52 (ACM) - C45*1-81 (E1) A52*2-52 (ACM) - C46*2-81 (E1) |
L - BR |
VSV (for engine mounting) |
Idling |
0 to 1.5 V |
| C45*1-49 (NSW) - C45*1-81 (E1) C46*2-49 (NSW) - C46*2-81 (E1) |
L - BR |
Park/neutral position switch |
Engine switch on (IG), shift lever in P or N |
Below 3 V |
| Engine switch on (IG), shift lever not in P and N |
11 to 14 V |
|||
| A38*1-41 (CANH) - C45*1-81 (E1) A52*2-41 (CANH) - C46*2-81 (E1) |
P - BR |
CAN communication line |
Engine switch on (IG) |
Pulse generation (see waveform 10) |
| A38*1-49 (CANL) - C45*1-81 (E1) A52*2-49 (CANL) - C46*2-81 (E1) |
B - BR |
CAN communication line |
Engine switch on (IG) |
Pulse generation (see waveform 11) |
| A38*1-47 (STSW) - C45*1-81 (E1) A52*2-47 (STSW) - C46*2-81 (E1) |
R - BR |
Engine switch signal |
Shift lever in P or N, engine switch pushed |
6.0 V or more |
| A38*1-22 (ACCR) - C45*1-81 (E1) A52*1-22 (ACCR) - C45*1-81 (E1) |
L-Y - BR |
ACC (Accessory) relay control signal |
Cranking |
Below 1.5 V |
| C45*1-52 (STAR) - C45*1-81 (E1) C46*2-52 (STAR) - C46*2-81 (E1) |
L - BR |
Starter relay control |
Engine switch on (IG) |
Below 1.5 V |
| Cranking |
6.0 V or more |
|||
| C45*1-54 (PRD) - C45*1-81 (E1) C46*2-54 (PRD) - C46*2-81 (E1) |
Y - BR |
Pressure discharge valve drive signal |
Engine warmed up, engine racing |
Pulse generation (See waveform 12) |
| C45*1-32 (RLFF) - C45*1-81 (E1) C46*2-32 (RLFF) - C46*2-81 (E1) |
R - BR |
Pressure discharge valve confirmation signal |
Engine warmed up, engine racing |
Pulse generation (See waveform 12) |
| C45*1-120 (VNVC) - C45*1-97 (VNE2) C46*2-120 (VNVC) - C46*2-97 (VNE2) |
W - R |
Power source of nozzle vane position sensor |
Engine switch on (IG) |
4.5 to 5.5 V |
| C45*1-74 (VNA) - C45*1-97 (VNE2) C46*2-74 (VNA) - C46*2-97 (VNE2) |
BR - R |
Nozzle vane position sensor (for bank 1) |
Engine switch on (IG) |
2.3 to 2.7 V |
| C45*1-117 (VNA2) - C45*1-97 (VNE2) C46*2-117 (VNA2) - C46*2-97 (VNE2) |
B - R |
Nozzle vane position sensor (for bank 2) |
Engine switch on (IG) |
2.3 to 2.7 V |
| C45*1-122 (THCF) - C45*1-99 (ETCF) C46*2-122 (THCF) - C46*2-99 (ETCF) |
L - BR |
Exhaust gas temperature sensor (B1S1) |
Engine warmed up, idling |
4.6 to 4.9 V |
| C45*1-121 (THCI) - C45*1-99 (ETCF) C46*2-121 (THCI) - C46*2-99 (ETCF) |
G-Y - BR |
No. 2 Exhaust gas temperature sensor (B1S2) |
Engine warmed up, idling |
4.6 to 4.9 V |
| C45*1-123 (THCO) - C45*1-99 (ETCF) C46*2-123 (THCO) - C46*2-99 (ETCF) |
W - BR |
No. 4 Exhaust gas temperature sensor (B1S3) |
Engine warmed up, idling |
4.6 to 4.9 V |
| C45*1-68 (TCF2) - C45*1-99 (ETCF) C46*2-68 (TCF2) - C46*2-99 (ETCF) |
G-B - BR |
Exhaust gas temperature sensor (B2S1) |
Engine warmed up, idling |
4.6 to 4.9 V |
| C45*1-98 (TCI2) - C45*1-99 (ETCF) C46*2-98 (TCI2) - C46*2-99 (ETCF) |
P-L - BR |
No. 3 Exhaust gas temperature sensor (B2S2) |
Engine warmed up, idling |
4.6 to 4.9 V |
| C45*1-124 (TCO2) - C45*1-99 (ETCF) C46*2-124 (TCO2) - C46*2-99 (ETCF) |
P-L - BR |
No. 4 Exhaust gas temperature sensor (B2S3) |
Engine warmed up, idling |
4.6 to 4.9 V |
| C45*1-83 (FIV) - C45*1-81 (E1) C46*2-83 (FIV) - C46*2-81 (E1) |
W - BR |
Exhaust fuel addition injector assembly (for bank 1) |
Exhaust fuel addition injector assembly (for bank 1) operating |
Pulse generation |
| C45*1-84 (FIV2) - C45*1-81 (E1) C46*2-84 (FIV2) - C46*2-81 (E1) |
G - BR |
Exhaust fuel addition injector assembly (for bank 2) |
Exhaust fuel addition injector assembly (for bank 2) operating |
Pulse generation |
| C45*1-45 (HA1A) - C45*1-44 (E04) C46*2-45 (HA1A) - C46*2-44 (E04) |
L - BR |
Air fuel ratio sensor heater (for bank 1) |
Engine switch on (IG) |
Pulse generation |
| C45*1-102 (A1A+) - C45*1-44 (E04) C46*2-102 (A1A+) - C46*2-44 (E04) |
G - BR |
Air fuel ratio sensor (for bank 1) |
Engine switch on (IG) |
2.0 to 2.5 V |
| C45*1-103 (A1A-) - C45*1-44 (E04) C46*2-103 (A1A-) - C46*2-44 (E04) |
R - BR |
Air fuel ratio sensor (for bank 1) |
Engine switch on (IG) |
2.0 to 2.5 V |
| C45*1-46 (HA2A) - C45*1-23 (E05) C46*2-46 (HA2A) - C46*2-23 (E05) |
L - W-B |
Air fuel ratio sensor heater (for bank 2) |
Engine switch on (IG) |
Pulse generation |
| C45*1-125 (A2A+) - C45*1-23 (E05) C46*2-125 (A2A+) - C46*2-23 (E05) |
G - W-B |
Air fuel ratio sensor (for bank 2) |
Engine switch on (IG) |
2.0 to 2.5 V |
| C45*1-126 (A2A-) - C45*1-23 (E05) C46*2-126 (A2A-) - C46*2-23 (E05) |
R - W-B |
Air fuel ratio sensor (for bank 2) |
Engine switch on (IG) |
2.0 to 2.5 V |
| C45*1-69 (PEX) - C45*1-92 (E2) C46*2-69 (PEX) - C46*2-92 (E2) |
R - BR |
Differential pressure sensor (for bank 1) |
Engine switch on (IG) |
0.4 to 4.8 V |
| C45*1-70 (PEX2) - C45*1-92 (E2) C46*2-70 (PEX2) - C46*2-92 (E2) |
R - BR |
Differential pressure sensor (for bank 2) |
Engine switch on (IG) |
0.4 to 4.8 V |
- HINT:
- *1: for LHD
- *2: for RHD
- *1: for LHD
| WAVEFORM 1 |
![]() ![]() |
| ECM Terminal Name |
From #1 to #8 and E1 |
| Tester Range |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the injector injection.
| WAVEFORM 2 |
![]() ![]() |
| ECM Terminal Name |
PCV+ and PCV- |
| Tester Range |
10 V/DIV., 5 msec./DIV. |
| Condition |
Idling or cranking with warm engine |
- HINT:
- The waveform varies depending on the suction control valve operation.
| WAVEFORM 3 |
![]() ![]() |
| ECM Terminal Name |
INJ1 and E1 INJ2 and E1 |
| Tester Range |
2 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the injector injection.
| WAVEFORM 4 |
![]() ![]() |
| ECM Terminal Name |
LUSL and E1 LUS2 and E1 |
| Tester Range |
1 V/DIV., 2 msec./DIV. |
| Condition |
Racing with warm engine |
- HINT:
- The waveform varies depending on the throttle valve operation.
| WAVEFORM 5 |
![]() ![]() |
| ECM Terminal Name |
EGRS and E1 ERS2 and E1 |
| Tester Range |
5 V/DIV., 5 msec./DIV. |
| Condition |
Idling |
- HINT:
- The waveform varies depending on the throttle valve operation.
| WAVEFORM 6 |
![]() ![]() |
| ECM Terminal Name |
M+ and E1 VN2+ and E1 |
| Tester Range |
5 V/DIV., 20 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the turbocharger operation.
| WAVEFORM 7 |
![]() ![]() |
| ECM Terminal Name |
M- and E1 VN2- and E1 |
| Tester Range |
5 V/DIV., 50 msec./DIV. |
| Condition |
Idling with warm engine |
- HINT:
- The waveform varies depending on the turbocharger status.
| WAVEFORM 8 |
![]() ![]() |
| ECM Terminal Names |
TACH and E1 |
| Tester Range |
5 V/DIV., 10 msec./DIV. |
| Conditions |
Idling |
- HINT:
- The wavelength becomes shorter as the engine speed increases.
| WAVEFORM 9 |
![]() ![]() |
| ECM Terminal Name |
SPD and E1 |
| Tester Range |
5 V/DIV., 10 msec./DIV. |
| Condition |
Driving at vehicle speed of 40 km/h (25 mph) |
- HINT:
- The wavelength becomes shorter as the vehicle speed increases.
| WAVEFORM 10 |
![]() ![]() |
| ECM Terminal Name |
CAN+ and E1 |
| Tester Range |
1 V/DIV., 10 msec./DIV. |
| Condition |
Engine stopped, engine switch on (IG) |
- HINT:
- The waveform varies depending on the CAN communication signal.
| WAVEFORM 11 |
![]() ![]() |
| ECM Terminal Name |
CAN- and E1 |
| Tester Range |
1 V/DIV., 10 msec./DIV. |
| Condition |
Engine stopped, engine switch on (IG) |
- HINT:
- The waveform varies depending on the CAN communication signal.
| WAVEFORM 12 |
![]() ![]() |
| ECM Terminal Name |
(a) PRD and E1 (b) RLFF and E1 |
| Tester Range |
2 V/DIV., 1 msec./DIV. |
| Condition |
Engine warmed up, engine racing |
- HINT:
- The wavelength becomes shorter as the engine speed increases.











