2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the cables from the negative (-) main battery and sub-battery terminals.


2. REMOVE UPPER RADIATOR SUPPORT SEAL
  1. Remove the 7 clips and upper radiator support seal.


3. REMOVE FRONT WHEEL RH

4. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Remove the 3 clips and front fender apron seal front RH.


5. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. A174148
    Remove the 3 bolts and screw.

  1. Loosen the clip and remove the splash shield.


6. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH
  1. Remove the 3 bolts and screw.

  1. Loosen the clip and remove the splash shield.


7. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and under cover.


8. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator reservoir cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

HINT:
Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator reservoir cap to drain the coolant in the radiator.

  1. Loosen the oil filter bracket drain cock plug to drain the coolant in the engine.

    A174741E01

  1. Tighten the radiator drain cock plug by hand.

  1. A177208
    Tighten the oil filter bracket drain cock plug.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }


9. REMOVE NO. 3 ENGINE ROOM WIRE
  1. Disconnect the 4 wire harness clamps.

  1. Remove the 2 nuts and No. 3 engine room wire.

    A174837


10. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

  1. A174701
    Remove the 2 nuts and No. 1 engine cover.


11. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

  1. A174698
    Loosen the hose clamp.

  1. Disconnect the mass air flow meter connector and using a clip remover, detach the wire harness clamp from the air cleaner cap.

  1. Detach the 4 clamps and remove the air cleaner cap.


12. REMOVE NO. 1 AIR CLEANER HOSE

  1. A174699
    Loosen the hose clamp and remove the No. 1 air cleaner hose.


13. REMOVE INTAKE AIR CONNECTOR

  1. A174749E01
    w/o Viscous Heater:

    1. Disconnect the connector from the water temperature sensor.

    2. Using a clip remover, detach the 3 wire harness clamps.

  1. w/ Viscous Heater:

    1. Disconnect the 2 connectors from the viscous with magnet clutch heater and water temperature sensor.

    2. Using a clip remover, detach the 3 wire harness clamps.

  1. A174710
    Loosen the 2 hose clamps and remove the 2 bolts and intake air connector.


14. REMOVE VANE PUMP OIL RESERVOIR ASSEMBLY

  1. A177428
    Insert a screwdriver between the reservoir and oil reservoir bracket, push the claw, and then disconnect the reservoir by pulling it upwards.


15. REMOVE NO. 1 OIL RESERVOIR BRACKET

  1. A184319
    Remove the 2 bolts and bracket.


16. REMOVE RADIATOR RESERVOIR ASSEMBLY

  1. A174735
    Disconnect the 2 hoses.

  1. Remove the 3 bolts and radiator reservoir.


17. REMOVE VANE PUMP ASSEMBLY

  1. C172309
    Remove the 2 nuts and vane pump.

  1. Remove the O-ring from the vane pump.


18. DISCONNECT NO. 1 RADIATOR HOSE

19. DISCONNECT NO. 2 RADIATOR HOSE

20. REMOVE V-RIBBED BELT (w/ Viscous Heater)

  1. A174847
    Loosen the lock nut and turn the bolt counterclockwise.

  1. Remove the V-ribbed belt.


21. REMOVE NO. 1 IDLER PULLEY (w/ Viscous Heater)

  1. A177430
    Remove the bolt, cover, No. 1 idler pulley and collar.


22. REMOVE NO. 3 IDLER PULLEY (w/ Viscous Heater)

  1. A177431
    Remove the nut and No. 3 idler pulley.


23. REMOVE V-RIBBED BELT

  1. A174849
    Using a wrench to the V-ribbed belt tensioner bracket, turn the wrench clockwise and remove the V-ribbed belt.


24. REMOVE OIL COOLER TUBE (for Automatic Transmission)

  1. C167861
    Disconnect the inlet and outlet No. 1 oil cooler hose.

  1. C175574
    Disconnect the inlet No. 2 and No. 3 oil cooler hoses.

  1. C175575
    Disconnect the inlet No. 4 oil cooler hose.

  1. C167866
    Remove the 2 bolts and transmission oil cooler tube.


25. REMOVE FAN SHROUD WITH FAN

  1. A161930
    Loosen the 4 nuts holding the fluid coupling fan.

  1. A177427
    Remove the 2 bolts holding the fan shroud.

  1. A179253
    Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.


26. REMOVE FAN PULLEY

27. REMOVE HEATER WATER PIPE SUB-ASSEMBLY (w/ Viscous Heater)

  1. A179255
    Remove the 4 bolts and disconnect the heater water pipe from the viscous heater with magnet clutch.


28. REMOVE VISCOUS WITH MAGNET CLUTCH HEATER ASSEMBLY (w/ Viscous Heater)

E154426
  1. Disconnect the connector and detach the clamp.

  1. Using pliers, grip the claws of the clips and slide the 2 clips.

  1. Disconnect the 2 heater hoses.

  1. Remove the 2 bolts and heater assembly.


29. REMOVE NO. 1 IDLER PULLEY BRACKET (w/ Viscous Heater)

  1. A177432
    Remove the bolt and No. 1 idler pulley bracket.


30. REMOVE WATER INLET

  1. A174815
    Disconnect the No. 2 oil cooler hose from the water pump and clamp.

  1. A174816
    Remove the 4 bolts and water inlet.


31. REMOVE THERMOSTAT
  1. Remove the thermostat.

  1. Remove the gasket from the thermostat.


32. REMOVE NO. 2 IDLER PULLEY (w/ Viscous Heater)

  1. A177433
    Remove the bolt, cover, No. 2 idler pulley and collar.


33. REMOVE NO. 2 IDLER PULLEY BRACKET (w/ Viscous Heater)

  1. E154425
    Remove the 3 bolts and idler pulley bracket.


34. DISCONNECT NO. 1 OIL COOLER HOSE

A174819

35. REMOVE FAN BRACKET SUB-ASSEMBLY

  1. A174820
    Remove the 4 bolts and fan bracket.


36. REMOVE WATER OUTLET

  1. A161939
    Disconnect the engine coolant temperature sensor connector.

  1. Remove the 2 bolts, disconnect the water outlet from the No. 2 water hose joint, and remove the water outlet and gasket.


37. REMOVE WATER PUMP ASSEMBLY

  1. A174821
    Remove the 9 bolts, 2 nuts, water pump and gasket.

← ON-VEHICLE INSPECTION (from Sep 2011)REMOVAL (from Jan 2012) →