2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REPLACEMENT

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the loss of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash the area thoroughly with soap and waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.
  3. In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.


1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A174194
    Remove the 2 bolts and service hole cover from the No. 2 engine under cover.

  1. Remove the oil drain plug, and drain the engine oil from the oil pan.

    NOTICE:
    Collect the oil in an oil disposal container.

  1. Wipe the oil pan and drain plug.

  1. Install a new gasket and the drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }


2. REMOVE OIL FILTER SUB-ASSEMBLY
  1. Remove the drain pipe cap.

  1. A174331E01
    Using SST, remove the oil filter.
    SST
    09228-07501  

    HINT:
    1. Put the disposal container beneath the drain hose to collect the oil from the oil filter cover.
    2. Drain hose inside diameter: 8 mm (0.315 in.)
    3. Drain hose length: 900 mm (2.95 ft.)


3. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. A174332E01
    Using SST, tighten the oil filter. Depending on the work space available, choose from the following.
    SST
    09228-07501  

    1. If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or with a common wrench.

  1. A174194
    Install the service hole cover to the No. 2 engine under cover with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


4. ADD ENGINE OIL
  1. Remove the oil filler cap.

  1. Add new oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    5W-30
    10W-30
    API grade SL, SM or SN multigrade engine oil
    15W-40
    20W-50


    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 Imp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 Imp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 Imp. qts)

  1. Install the oil filler cap.


5. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


6. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine so that the coolant temperature is approximately 80°C (176°F). Check the engine oil level dipstick 5 minutes after the engine is stopped. Then add engine oil to the full level of the engine oil level dipstick.

← COMPONENTS (from Jan 2012)REPLACEMENT (from Jan 2012) →