2011-2013 Land Cruiser · Service Manual Brake

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. REMOVE NO. 1 BRAKE ACTUATOR BRACKET

  1. C172196
    Using a 5 mm hexagon wrench, remove the bolt and No. 1 brake actuator bracket.

  1. F051180
    Using a screwdriver, disconnect the brake fluid level warning switch connector from the No. 1 brake actuator bracket.


2. REMOVE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY

  1. C172197E01
    Using a pin punch and hammer, remove the pin from the brake master cylinder reservoir.

  1. C172198
    Remove the screw and pull out the brake master cylinder reservoir sub-assembly.

  1. Remove the master cylinder reservoir filler cap.


3. REMOVE MASTER CYLINDER RESERVOIR GROMMET

  1. C172199
    Remove the 3 reservoir grommets from the master cylinder reservoir.


4. REMOVE NO. 1 BRAKE ACTUATOR HOSE

  1. C172887
    Using needle nose pliers, slide the 2 clips and remove the brake actuator hose and 2 clips.


5. REMOVE NO. 1 BRAKE ACTUATOR TUBE

  1. C172888E01
    Using a union nut wrench, remove the No. 1 brake actuator tube.


6. REMOVE BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY

  1. F051185E01
    Using a screwdriver, remove the 2 plugs.

  1. F051186E02
    Remove the 2 screws and disconnect the wire harnesses from the master cylinder solenoid.

  1. F051187
    Using a screwdriver, remove the clip.

  1. C177150E01
    Remove the brake booster with accumulator pump assembly from the brake master cylinder.

  1. Remove the 2 brake booster pump collars and 2 brake booster pump bushes from the brake booster with accumulator pump assembly.

  1. F051415E03
    Using a 4 mm hexagon wrench, remove the 2 pins.


7. REMOVE NO. 1 BRAKE BOOSTER PUMP BRACKET

  1. F051189E02
    Using a 5 mm hexagon wrench, remove the 2 bolts and No. 1 brake booster pump bracket from the brake master cylinder solenoid.

  1. Remove the brake booster pump bush from the No. 1 brake booster pump bracket.


8. REMOVE BRAKE BOOSTER ACCUMULATOR PIPE

  1. C172891
    Secure the brake booster with accumulator pump assembly in a vise.

  1. Remove the brake booster accumulator.

  1. Remove the O-ring from the brake booster accumulator.

    NOTICE:
    Ensure no foreign matter enters the pump.

  1. Remove the brake booster accumulator pipe and compression spring.


9. REMOVE MASTER CYLINDER SOLENOID

  1. F051195E02
    Remove the 6 bolts and master cylinder solenoid.

  1. F051196
    Remove the gasket.


10. REMOVE MASTER CYLINDER PUSH ROD CLEVIS

  1. C177091
    Loosen the lock nut on the rod operating adapter, and remove the push rod clevis and lock nut.

  1. F051192E02
    Loosen the lock nut on the brake master cylinder side, and remove the rod operating adapter and lock nut.


11. REMOVE MASTER CYLINDER BOOT

12. REMOVE BRAKE BOOSTER PISTON SUB-ASSEMBLY

  1. F051417E03
    Pressing the piston in with a screwdriver, insert a pin or equivalent from the hole in the master cylinder body to hold the C-ring, and then remove it with another screwdriver.

    HINT:
    Tape the screwdriver tip before use.

  1. Remove the plug from the piston.

  1. Remove the piston by pulling it straight out, not at an angle.

    NOTICE:
    If the piston is pulled out at an angle, there is a possibility that the cylinder bore could be damaged.

← REMOVAL (from Jan 2012)INSPECTION (from Sep 2011) →