2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL OIL COOLER ASSEMBLY
  1. Clean the oil cooler contact surface on the cooler mounting.

  1. Apply a light coat of engine oil to a new O-ring, and install it into the oil cooler.

  1. Apply a light coat of engine oil to the threads of the oil cooler union bolt.

  1. A175339
    Align the protrusion of the oil filter bracket with the cutout of the oil cooler.

  1. Install the oil cooler with the plate washer and oil cooler union bolt.

    Torque:
    68 N*m{ 693 kgf*cm , 50 ft.*lbf }

  1. A174351
    Install the oil cooler hose and No. 2 oil cooler hose.


2. INSTALL OIL FILTER SUB-ASSEMBLY
  1. Check and clean the oil filter installation surface.

  1. Apply clean engine oil to the gasket of a new oil filter.

  1. Lightly screw the oil filter into place by hand. Tighten it until the gasket contacts the seat.

  1. A174332E01
    Using SST, tighten the oil filter. Depending on the work space available, choose from the following.
    SST
    09228-07501  

    1. If enough space is available, use a torque wrench to tighten the oil filter.

      Torque:
      17 N*m{ 173 kgf*cm , 13 ft.*lbf }

    2. If enough space is not available to use a torque wrench, tighten the oil filter a 3/4 turn by hand or with a common wrench.

  1. A174194
    Install the service hole cover to the No. 2 engine under cover with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


3. INSTALL V-BANK COVER

  1. A174359
    Install the V-bank cover with the 2 cap nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


4. ADD ENGINE OIL
  1. Remove the oil filler cap.

  1. Add new oil.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "Energy-Conserving", SM "Energy-Conserving", SN "Resource-Conserving" or ILSAC multigrade engine oil
    5W-30
    10W-30
    API grade SL, SM or SN multigrade engine oil
    15W-40
    20W-50


    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill with oil filter change
    5.2 liters (5.5 US qts, 4.6 Imp. qts)
    Drain and refill without oil filter change
    4.9 liters (5.2 US qts, 4.3 Imp. qts)
    Dry fill
    6.0 liters (6.3 US qts, 5.3 Imp. qts)

  1. Install the oil filler cap.


5. INSPECT FOR ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the low and full level marks on the dipstick.
    If the oil level is low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


6. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified condition
    for Automatic transmission
    w/o Rear Heater
    11.2 liters (11.8 US qts, 9.9 Imp. qts)
    w/ Rear Heater
    14.4 liters (15.2 US qts, 12.7 Imp. qts)
    for Manual transmission
    w/o Rear Heater
    12.0 liters (12.7 US qts, 10.6 Imp. qts)
    w/ Rear Heater
    14.6 liters (15.4 US qts, 12.8 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A174295E01
    Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the reservoir cap.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Set the air conditioning as follows while warming up the engine.

    Item
    Condition
    Fan speed
    Any setting except off
    Temperature
    Toward WARM
    Air conditioning switch
    Off

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the No. 2 radiator hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the No. 1 and No. 2 radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves. Heat areas on the parts may injure your hands.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174297E01
    Check that the coolant level is between the F and L lines.
    If the coolant level is below the L line, repeat all of the procedures above.
    If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.


7. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


8. INSPECT FOR ENGINE COOLANT LEAK

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A174294
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.


9. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. B180889
    Install the radiator support seal with the 7 clips.


10. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Install the under cover with the 10 bolts.


11. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


12. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.

← INSPECTION (from Jan 2012)INSTALLATION (from Jan 2012) →