2011-2013 Land Cruiser · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built from Sep 2011


1. DRAIN CLUTCH FLUID

2. REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

B292994E01
  1. Put protective tape around the No. 2 instrument panel finish panel cushion.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 7 claws and remove the No. 2 instrument panel finish panel cushion.


3. REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

B292995
  1. Remove the clip and screw.

  1. Detach the 8 claws.

  1. Disconnect the connectors, detach the 2 clamps and remove the lower instrument panel pad sub-assembly.


4. REMOVE INSTRUMENT SIDE PANEL LH

E154740E06
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 6 claws and remove the instrument side panel.


5. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E154744E04
  1. Place protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a moulding remover, detach the 3 claws and remove the No. 1 instrument cluster finish panel garnish.


6. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH
  1. Place protective tape as shown in the illustration.

  1. Using a moulding remover, detach the 2 claws and remove the No. 2 instrument cluster finish panel garnish.

    B291251E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System
    *1
    Protective Tape
    -
    -


7. REMOVE FRONT DOOR SCUFF PLATE LH

B181682
  1. Detach the 7 claws and 4 clips, and remove the scuff plate.


8. REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B180655
  1. Remove the 2 screws.

  1. Detach the 3 claws.

  1. Disconnect the connectors and remove the No. 1 instrument panel under cover.


9. REMOVE COWL SIDE TRIM BOARD LH

B181911
  1. Remove the cap nut.

  1. Detach the 2 clips and remove the cowl side trim board.


10. REMOVE LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL

B180295E02
  1. Using a screwdriver, detach the 2 claws and open the hole cover.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape

  1. w/ Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 16 claws.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Remove the 2 bolts.

    2. Detach the 9 claws.

      B291250

  1. B180296
    for Automatic Air Conditioning System:

    1. Detach the 2 claws and remove the room temperature sensor.

  1. B181942
    Detach the 2 claws and disconnect the 2 control cables.

  1. Disconnect the connectors and remove the lower No. 1 instrument panel finish panel.


11. REMOVE NO. 1 SWITCH HOLE BASE

B180298
  1. Detach the 4 claws.

  1. Disconnect the connectors and remove the No. 1 switch hole cover.


12. REMOVE DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189602E01
    Remove the 5 bolts and driver side knee airbag.

  1. Disconnect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.


13. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299
  1. Detach the 2 claws and disconnect the DLC3.

  1. Remove the 5 bolts and lower instrument panel.


14. REMOVE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

  1. C173731
    Remove the 3 bolts.

  1. C173730
    Disconnect the 9 ECU connectors and remove the ECU.


15. DISCONNECT CLUTCH MASTER CYLINDER TO FLEXIBLE HOSE TUBE AND CLUTCH RESERVOIR TUBE

C172961
  1. Using a union nut wrench, disconnect the flexible hose tube.

    HINT:
    Use a container to catch the fluid.

  1. Disconnect the clutch reservoir tube.


16. REMOVE CLUTCH PEDAL SUPPORT ASSEMBLY WITH CLUTCH MASTER CYLINDER
  1. Disconnect the clutch start switch connector.

  1. w/ Cruise Control System:
    Disconnect the clutch switch connector.

  1. C172960
    Remove the 2 nuts, bolt and clutch pedal support with clutch master cylinder.


17. REMOVE TURNOVER SPRING

C172963
  1. Move the pedal to the full stroke position.

  1. Remove the turnover spring.


18. REMOVE CLUTCH PEDAL SPRING

C172964
  1. Remove the 2 E-rings and the spring with spacer.

  1. Remove the spacer from the spring.


19. REMOVE CLUTCH PEDAL SUB-ASSEMBLY

  1. C173251
    Remove the clip, wave washer and clevis pin.

  1. C172966
    Remove the nut, washer and bolt.

  1. Remove the clutch pedal from the clutch pedal support.


20. REMOVE CLUTCH PEDAL PAD
  1. Remove the clutch pedal pad from the clutch pedal.


21. REMOVE CLUTCH PEDAL SHAFT COLLAR

C173259
  1. Remove the clutch pedal shaft collar from the clutch pedal.


22. REMOVE CLUTCH PEDAL BUSH

  1. C173258
    Remove the 2 bushes from the clutch pedal.


23. REMOVE NO. 2 CLUTCH PEDAL CUSHION

  1. C175001
    Remove the 2 clutch pedal cushions from the clutch pedal.


24. REMOVE CLUTCH PEDAL TURNOVER BUSH

C173256
  1. Remove the clutch pedal turnover bush from the clutch pedal.


25. REMOVE CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSH

  1. C173254
    Remove the push rod clevis bush from the clutch pedal.


26. REMOVE CLUTCH PEDAL SPRING HOLDER

  1. C175002
    Remove the clutch pedal spring holder from the clutch pedal support.

← COMPONENTS (from Sep 2011)ADJUSTMENT (from Sep 2011) →