2011-2013 Land Cruiser · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. INSPECT 3RD GEAR THRUST CLEARANCE

C171239E01
  1. Using a feeler gauge, measure the 3rd gear thrust clearance.

    Standard Clearance:
    0.10 to 0.45 mm (0.00394 to 0.0177 in.)

    If the clearance is outside the specification, replace the defective gear, spacer or shaft.


2. INSPECT 5TH GEAR THRUST CLEARANCE

C171239E03
  1. Using a feeler gauge, measure the 5th gear thrust clearance.

    Standard Clearance:
    0.10 to 0.35 mm (0.00394 to 0.0137 in.)

    If the clearance is outside the specification, replace the defective gear, spacer or shaft.


3. INSPECT 2ND GEAR THRUST CLEARANCE

C171239E04
  1. Using a feeler gauge, measure the 2nd gear thrust clearance.

    Standard Clearance:
    0.10 to 0.35 mm (0.00394 to 0.0137 in.)

    If the clearance is outside the specification, replace the defective gear, spacer or shaft.


4. INSPECT 1ST GEAR THRUST CLEARANCE

C171239E05
  1. Using a feeler gauge, measure the 1st gear thrust clearance.

    Standard Clearance:
    0.10 to 0.45 mm (0.00394 to 0.0177 in.)

    If the clearance is outside the specification, replace the defective gear, spacer or shaft.


5. INSPECT 3RD GEAR RADIAL CLEARANCE

C171240
  1. Using a dial indicator, measure the 3rd gear radial clearance.

    Standard Clearance:
    0.020 to 0.073 mm (0.000788 to 0.00287 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.


6. INSPECT 5TH GEAR RADIAL CLEARANCE

C174152
  1. Using a dial indicator, measure the 5th gear radial clearance.

    Standard Clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.


7. INSPECT 2ND GEAR RADIAL CLEARANCE

C174153
  1. Using a dial indicator, measure the 2nd gear radial clearance.

    Standard Clearance:
    0.015 to 0.068 mm (0.000591 to 0.00267 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.


8. INSPECT 1ST GEAR RADIAL CLEARANCE

C174154
  1. Using a dial indicator, measure the 1st gear radial clearance.

    Standard Clearance:
    0.020 to 0.073 mm (0.000788 to 0.00287 in.)

    If the clearance is outside the specification, replace the defective gear, needle roller bearing or shaft.


9. REMOVE REVERSE GEAR SNAP RING

C171241
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


10. REMOVE 1ST GEAR

C171245
  1. Shift the No. 1 transmission hub sleeve to the 2nd gear.

  1. C171246E01
    Using SST and a press, remove the bearing, 1st gear and synchronizer ring.
    SST
    09555-55010  


11. REMOVE 1ST GEAR NEEDLE ROLLER BEARING
  1. Remove the 1st gear needle roller bearing from the output shaft.


12. REMOVE NO. 1 SYNCHRONIZER RING SET
  1. Remove the No. 1 synchronizer ring from the 1st gear.


13. REMOVE NO. 1 CLUTCH HUB SHAFT SNAP RING

C171247
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


14. REMOVE 2ND GEAR

C171248
  1. Using a press, remove the 2nd gear and synchronizer ring.


15. REMOVE 2ND GEAR NEEDLE ROLLER BEARING
  1. Remove the 2nd gear needle roller bearing from the output shaft.


16. REMOVE NO. 2 SYNCHRONIZER RING SET
  1. Remove the No. 2 synchronizer ring set from the 2nd gear.


17. REMOVE NO. 1 TRANSMISSION HUB SLEEVE

C171249E07
  1. Remove the No. 1 transmission hub sleeve, 3 shifting keys and 2 springs from the No. 1 transmission clutch hub.

    HINT:
    Use a piece of cloth to prevent the spring from flying off.


18. REMOVE NO. 2 CLUTCH HUB SETTING SHAFT SNAP RING

C171250
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


19. REMOVE 3RD GEAR

C171251
  1. Shift the No. 3 transmission hub sleeve to the 5th gear.

  1. C171252E01
    Using SST and a press, remove the 3rd gear and synchronizer ring.
    SST
    09555-55010  


20. REMOVE 3RD GEAR NEEDLE ROLLER BEARING
  1. Remove the 3rd gear needle roller bearing from the output shaft.


21. REMOVE NO. 3 SYNCHRONIZER RING SET
  1. Remove the No. 3 synchronizer ring set from the 3rd gear.


22. REMOVE NO. 2 TRANSMISSION HUB SLEEVE

C171249E08
  1. Remove the No. 2 transmission hub sleeve, 3 shifting keys and 2 springs from the No. 2 transmission clutch hub.

    HINT:
    Use a piece of cloth to prevent the spring from flying off.


23. REMOVE NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

C171254
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


24. REMOVE 5TH GEAR

C171255E01
  1. Using SST and a press, remove the 5th gear and synchronizer ring.

    SST
    09555-55010  


25. REMOVE 5TH COUNTER GEAR BEARING
  1. Remove the 5th counter gear bearing from the output shaft.


26. REMOVE NO. 3 SYNCHRONIZER RING SET
  1. Remove the No. 3 synchronizer ring from the 5th gear.


27. REMOVE NO. 3 TRANSMISSION HUB SLEEVE

C171249E09
  1. Remove the No. 3 transmission hub sleeve, 3 shifting keys and 2 springs from the No. 3 transmission clutch hub.

    HINT:
    Use a piece of cloth to prevent the spring from flying off.

← COMPONENTS (from Sep 2011)INSPECTION (from Sep 2011) →