2011-2013 Land Cruiser · Service Manual Drivetrain

DISASSEMBLY

Removal / installation · Vehicles built from Sep 2011


1. REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY (for 1GR-FE)

C178013
  1. Loosen the hose clamp, and remove the breather hose.


2. REMOVE TRANSMISSION BREATHER SUB-ASSEMBLY (for 1VD-FTV)

C178014
  1. Remove the wire harness clamp.

  1. Loosen the hose clamp, and remove the breather hose.


3. REMOVE CLUTCH HOUSING

C174421E03
  1. Remove the 10 bolts and clutch housing.


4. REMOVE FILLER PLUG

C174902
  1. Remove the filler plug.

  1. Remove the gasket from the filler plug.


5. REMOVE DRAIN PLUG

C172955
  1. Remove the drain plug.

  1. Remove the gasket from the drain plug.


6. REMOVE MANUAL TRANSMISSION CASE PLUG

C174726
  1. Using a T55 "TORX" socket wrench, remove the transmission case plug.

  1. Remove the gasket from the transmission case plug.


7. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY

C174428E01
  1. Disconnect the wire harness clamp.

  1. Using SST, remove the back-up light switch and gasket.

    SST
    09817-16011  


8. REMOVE SHIFT POSITION SWITCH (for 1VD-FTV)

C174429E01
  1. Disconnect the wire harness clamp.

  1. Using SST, remove the shift position switch and gasket.

    SST
    09817-16011  


9. REMOVE CONTROL SHAFT COVER

C174728
  1. Remove the 6 bolts and control shaft cover.


10. REMOVE REVERSE RESTRICT PIN ASSEMBLY

C174430
  1. Remove the 2 restrict pins.


11. REMOVE FLOOR SHIFT CONTROL SHIFT LEVER RETAINER SUB-ASSEMBLY

C174717
  1. Remove the 4 bolts.

  1. C174718
    Using a plastic-faced hammer, remove the floor shift control shift lever retainer.


12. REMOVE NO. 1 REVERSE RESTRICT PIN

C171347
  1. Remove the slotted pin.

  1. C171384
    Remove the No. 1 reverse restrict pin and spring.


13. REMOVE TRANSMISSION OIL PUMP COVER

C174391
  1. Remove the 5 bolts and oil pump cover.

  1. C171196
    Using a magnet hand, remove the 2 pins.

  1. Remove the oil pump cover O-ring from the oil pump cover.


14. REMOVE TRANSMISSION OIL PUMP COVER OIL SEAL

C178035E01
  1. Using a screwdriver, pry out the oil pump cover oil seal.

    NOTICE:
    Be careful not to damage the oil seal and oil pump cover contact surfaces.

    HINT:
    Tape the screwdriver tip before use.


15. REMOVE FRONT BEARING RETAINER (MTM)

C171381
  1. Remove the 8 bolts and front bearing retainer.


16. REMOVE TRANSMISSION FRONT BEARING RETAINER OIL SEAL

C171295E01
  1. Using a screwdriver, pry out the oil seal.

    NOTICE:
    Be careful not to damage the oil seal and front bearing retainer contact surfaces.

    HINT:
    Tape the screwdriver tip before use.


17. REMOVE SHIFT AND SELECT LEVER SHAFT

C174901
  1. Using a 14 mm hexagon wrench, remove the interlock hole plug.

  1. C174721E02
    Remove the 3 bolts, shift and select lever shaft, shift and select lever and shift lever housing.


18. REMOVE TRANSFER ADAPTER SUB-ASSEMBLY

C174720
  1. Remove the 11 bolts and transfer adapter.


19. REMOVE TRANSFER ADAPTER STRAIGHT PIN AND RING PIN

C178015E01
  1. Remove the 4 straight pins from the transfer adapter.

  1. Remove the 2 ring pins from the transfer adapter.


20. REMOVE TRANSFER ADAPTER PLUG

C174722
  1. Using a T40 "TORX" socket wrench, remove the transfer adapter plug.


21. REMOVE MANUAL TRANSMISSION OIL STRAINER SUB-ASSEMBLY

C171350E01
  1. Remove the 2 bolts and oil strainer.

  1. Remove the O-ring from the oil strainer.


22. REMOVE TRANSMISSION MAGNET

C171351
  1. Remove the transmission magnet.


23. REMOVE NO. 2 REVERSE IDLER THRUST WASHER

C171200
  1. Remove the thrust washer.


24. REMOVE REVERSE IDLER GEAR
  1. Remove the reverse idler gear.


25. REMOVE REVERSE IDLER GEAR BUSH OR BEARING
  1. Remove the bearing.


26. REMOVE REVERSE IDLER THRUST WASHER
  1. Remove the thrust washer.


27. REMOVE REVERSE IDLER GEAR SHAFT
  1. Remove the reverse idler gear shaft.


28. REMOVE REVERSE IDLER GEAR SHAFT WOODRUFF KEY
  1. Remove the woodruff key from the reverse idler gear shaft.


29. REMOVE MANUAL TRANSMISSION CASE SUB-ASSEMBLY

C171195
  1. Using a snap ring expander, remove the 2 snap rings from the input shaft and counter gear.

  1. C171197
    Using a brass bar and hammer, carefully tap the transmission case.

  1. Remove the transmission case from the intermediate plate.


30. REMOVE NO. 1 OIL RECEIVER PIPE (MTM)

C171354E01
  1. Remove the 2 bolts and oil receiver pipe from the transmission case.


31. REMOVE TRANSFER ADAPTER STRAIGHT PIN

C178017E01
  1. Remove the 4 straight pins from the transmission case.


32. REMOVE INTERMEDIATE PLATE STRAIGHT PIN

C178016E01
  1. Remove the 4 straight pins from the intermediate plate.


33. REMOVE MANUAL TRANSMISSION CASE RECEIVER

  1. C171355
    Remove the 3 bolts and oil receiver from the intermediate plate.


34. REMOVE SHIFT DETENT BALL PLUG

C171201
  1. Using a T40 "TORX" socket wrench, remove the 4 ball plugs.

  1. Using a magnet hand, remove the 4 springs and 4 balls.


35. REMOVE SHIFT FORK SHAFT SNAP RING

C171202
  1. Using 2 screwdrivers and a hammer, tap out the 4 snap rings.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


36. REMOVE NO. 4 GEAR SHIFT FORK SHAFT

C171203
  1. Remove the No. 4 gear shift fork set bolt.

  1. C171204
    Remove the No. 4 gear shift fork shaft and 2 balls.


37. REMOVE REVERSE SHIFT FORK
  1. Remove the reverse shift fork.


38. REMOVE NO. 3 GEAR SHIFT FORK SHAFT

C171205
  1. Using a magnet hand, remove the ball.

  1. C171216
    Remove the No. 3 gear shift fork set bolt.

  1. Remove the No. 3 shift gear fork shaft and reverse shift head.

  1. C171357
    Using a magnet hand, remove the interlock pin from the No. 3 gear shift fork shaft.


39. REMOVE NO. 3 GEAR SHIFT FORK
  1. Remove the No. 3 gear shift fork.


40. REMOVE NO. 1 GEAR SHIFT FORK SHAFT

C171217
  1. Using a magnet hand, remove the interlock pin.

  1. C171218
    Remove the No. 1 gear shift fork set bolt.

  1. Remove the No. 1 gear shift fork shaft.

  1. C171358
    Using a magnet hand, remove the interlock pin from the No. 1 gear shift fork shaft.


41. REMOVE NO. 1 GEAR SHIFT FORK
  1. Remove the No. 1 gear shift fork.


42. REMOVE NO. 2 GEAR SHIFT FORK SHAFT

C171219
  1. Using a magnet hand, remove the interlock pin.

  1. C171220
    Remove the No. 2 gear shift fork set bolt.

  1. Remove the No. 2 gear shift fork shaft.


43. REMOVE NO. 2 GEAR SHIFT FORK
  1. Remove the No. 2 gear shift fork.


44. REMOVE NO. 3 TRANSMISSION CLUTCH HUB SHAFT SNAP RING

C171222
  1. Using 2 screwdrivers and a hammer, tap out the snap ring.

    HINT:
    Use a piece of cloth to prevent the snap ring from flying off.


45. REMOVE NO. 4 TRANSMISSION CLUTCH HUB

C271140E01
  1. Using SST, remove the No. 4 transmission clutch hub.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03080)


46. REMOVE REVERSE GEAR

C171225
  1. Remove the reverse synchronizer ring set and reverse gear.


47. REMOVE REVERSE SYNCHRONIZER RING SET
  1. Remove the reverse synchronizer ring set from the reverse gear.


48. REMOVE REVERSE GEAR BEARING
  1. Remove the reverse gear bearing.


49. REMOVE NO. 1 TRANSMISSION HUB SLEEVE

C271141E01
  1. Remove the No. 1 transmission hub sleeve, 3 shifting keys, and 3 springs from the No. 4 transmission clutch hub.

    HINT:
    Use a piece of cloth to prevent the spring from flying off.


50. REMOVE OUTPUT SHAFT REAR BEARING(MTM) RETAINER

C171360
  1. Remove the 4 bolts and rear bearing retainer.


51. REMOVE COUNTER GEAR

C174896
  1. Using a snap ring expander, remove the snap ring.

  1. C171228E01
    Using SST, remove the outer race.
    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04020, 09955-04011, 09957-04010, 09958-04011)

    NOTICE:
    Do not drop the counter gear. Hold the front side of the counter gear when removing the bearing outer race.

  1. C171230
    Using a screwdriver, remove the center bearing and counter gear.


52. REMOVE INPUT SHAFT ASSEMBLY

C171362
  1. Remove the input shaft from the output shaft.

    NOTICE:
    Do not drop the input shaft bearing.


53. REMOVE NO. 2 SYNCHRONIZER RING
  1. Remove the No. 2 synchronizer ring from the input shaft.


54. REMOVE OUTPUT SHAFT BEARING SHAFT SNAP RING

C171364
  1. Using a snap ring expander, remove the snap ring.


55. REMOVE OUTPUT SHAFT ASSEMBLY

C171231
  1. Remove the output shaft from the intermediate plate by pulling on the output shaft and tapping on the intermediate plate with a plastic-faced hammer.

← COMPONENTS (from Sep 2011)REASSEMBLY (from Sep 2011) →