2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


INSPECT IGNITION TIMING

NOTICE:
  1. Turn all electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / IGN Advance.

    3. Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idling (transmission in neutral position and A/C switch off)

    4. Check that the ignition timing advances immediately when the engine speed is increased.

  1. H102392E79
    When not using the intelligent tester:

    1. Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.

      SST
      09843-18040  

      NOTICE:
      Be sure not to improperly connect the terminals. This may damage the engine.

    2. Remove the air cleaner cap.

    3. A158636
      Pull out the wire harness shown in the illustration.

    4. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      1. Use a timing light that detects primary signals.
      1. After checking, be sure to wrap the wire harness with tape.

    5. A076316E01
      Inspect the ignition timing during idling.

      Standard ignition timing:
      8 to 12° BTDC @ idling (transmission in neutral position and A/C switch off)

    6. Remove SST from the DLC3.

    7. Inspect the ignition timing during idling.

      Standard ignition timing:
      7 to 24° BTDC @ idling (transmission in neutral position and A/C switch off)

    8. Disconnect the timing light from the engine.

    9. Install the air cleaner cap.


INSPECT ENGINE IDLING SPEED

NOTICE:
  1. Turn all the electrical systems off.
  1. Perform the inspection when the cooling fan motor is turned off.

  1. Warm up the engine.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

    2. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Engine Speed.

    3. Inspect the engine idling speed.

      Standard idling speed:
      650 to 750 rpm (transmission in neutral position and A/C switch off)

  1. H102392E88
    When not using the intelligent tester:

    1. Connect SST to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Inspect the engine idling speed.

      Standard idling speed:
      650 to 750 rpm (transmission in neutral position and A/C switch off)


INSPECT COMPRESSION
  1. Warm up and stop the engine.

  1. Drain the engine coolant (Click here).

  1. A174355
    Remove the 2 cap nuts and V-bank cover.

  1. Loosen the clamp and remove the No. 2 air cleaner hose.

  1. A174356
    Disconnect the ventilation hose.

  1. A174357
    Disconnect the MAF connector.

  1. Using a clip remover, detach the 2 wire harness clamps.

  1. Disconnect the vacuum hose.

  1. A174358
    Loosen the hose clamp and remove the 2 bolts and air cleaner.

  1. Remove the intake air surge tank (Click here).

  1. Remove the 6 ignition coils.

  1. Remove the 6 spark plugs.

  1. Disconnect the 6 fuel injector connectors.

  1. A076317E01
    Inspect the cylinder compression pressure.

    1. Insert a compression gauge into the spark plug hole (Procedure "A").

    2. While cranking the engine, measure the compression pressure (Procedure "B").

      Compression pressure:
      1300 kPa (13.3 kgf/cm2, 189 psi)

      Minimum pressure:
      1000 kPa (10.2 kgf/cm2, 145 psi)

      Difference between each cylinder:
      100 kPa (1.0 kgf/cm2, 15 psi)

      HINT:
      1. Use a fully-charged battery so that the engine speed can be increased to 250 rpm or more.
      2. Measure the compression in as short a time as possible.

    3. Repeat procedures "A" and "B" for each cylinder.

    4. If the cylinder compression is low, pour a small amount of engine oil into the cylinder through the spark plug hole and repeat procedures "A" and "B" for cylinders with low compression.

      1. If adding oil increases the compression, the piston rings and/or cylinder bore may be worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage from the gasket.

  1. Connect the 6 injector connectors.

  1. Install the 6 spark plugs.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Install the 6 ignition coils.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the intake air surge tank (Click here).

  1. Install the air cleaner (Click here).

  1. Install the No. 2 air cleaner hose (Click here).

  1. A174359
    Install the V-bank cover with the 2 cap nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Add engine coolant (Click here).


INSPECT CO/HC

HINT:
This check is to determine whether or not the idle CO/HC concentration complies with regulations.

  1. Start the engine.

  1. Run the engine at 2500 rpm for approximately 180 seconds.

  1. A174360E01
    Insert the CO/HC meter testing probe at least 40 cm (1.31 ft) into the tailpipe during idling.

  1. Immediately check the CO/HC concentration during idling and/or at 2500 rpm.

    HINT:
    When carrying out the 2 tests (idling and 2500 rpm), the measurement orders are prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, perform troubleshooting in the order given below.

    1. Check the A/F sensor operation (Click here) and heated oxygen sensor operation (Click here).

    2. See the table below for possible causes, and then inspect and correct the corresponding causes if necessary.

      CO
      HC
      Symptom
      Causes
      Normal
      High
      Rough idling
      1. Faulty ignition:
        1. Incorrect timing
        2. Plugs are contaminated or shorted, or plug gaps are defective
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinders
      Low
      High
      Rough idling
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. Ventilation hoses
        2. Intake manifold
        3. Throttle body
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective engine coolant temperature sensor
        3. Faulty mass air flow meter
        4. Faulty ECM
        5. Faulty injectors
        6. Faulty throttle position sensor

← ON-VEHICLE INSPECTION (from Jan 2012)ON-VEHICLE INSPECTION (from Jan 2012) →