2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0115 Engine Coolant Temperature Circuit

Diagnostic trouble codes · Vehicles built from Jan 2012

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

A thermistor is built into the Engine Coolant Temperature (ECT) sensor and it changes its resistance value according to the engine coolant temperature.
The structure of the sensor and connection to the ECM is the same as the intake air temperature sensor.

HINT:
If DTC P0115, P0117 or P0118 is stored, the ECM operates the fail-safe function in which the ECT is assumed to be 80°C (176°F).

P0115 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Open or short in the engine coolant temperature (ECT) sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open or short in engine coolant temperature (ECT) sensor circuit
  2. ECT sensor
  3. ECM
P0117 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Short in the ECT sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Short in ECT sensor circuit
  2. ECT sensor
  3. ECM
P0118 
DTC Detection Drive Pattern
DTC Detection Condition
Trouble Area
Ignition switch ON for 0.5 seconds
Open in the ECT sensor circuit for 0.5 seconds (1 trip detection logic).
  1. Open in ECT sensor circuit
  2. ECT sensor
  3. ECM
Related Data List 
DTC No.
Data List
P0115
Coolant Temp
P0117
P0118

HINT:
  1. If DTC P0115, P0117and/or P0118 is stored, the following symptoms may appear:
    1. Misfire
    2. Combustion noise
    3. Black smoke
    4. White smoke
    5. Lack of power
  2. When DTC P0115, P0117 and/or P0118 is stored, check the engine coolant temperature by entering the following menus: Powertrain / Engine / Data List / Coolant Temp.
    Reference: 
    Temperature Displayed
    Malfunction
    -40°C (-40°F)
    Open circuit
    140°C (284°F) or higher
    Short circuit


WIRING DIAGRAM

A165735E06

INSPECTION PROCEDURE

NOTICE:
After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).

HINT:
  1. If DTCs relating to different systems are stored, and they share terminal E2 as their ground, check this ground circuit first.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.


1. READ VALUE USING INTELLIGENT TESTER (ENGINE COOLANT TEMPERATURE)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the value.

    OK:
    75 to 90°C (167 to 194°F) with warm engine.

    Result 
    Result
    Proceed to
    -40°C (-40°F)
    A
    140°C (284°F) or higher
    B
    75 to 90°C (167 to 194°F)
    C

    HINT:
    1. If there is an open circuit, the tester indicates -40°C (-40°F).
    2. If there is a short circuit, the tester indicates 140°C (284°F) or more.



B
Go to step 4

C
Go to step 11
A


2. READ VALUE USING INTELLIGENT TESTER (CHECK FOR OPEN IN WIRE HARNESS)

  1. A185902E01
    Disconnect the engine coolant temperature (ECT) sensor connector.

  1. Connect terminals 1 and 2 of the ECT sensor wire harness side connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the value.

    OK:
    140°C (284°F) or higher



OK
Go to step 7

NG
Go to step 3
3. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A185903E01
    Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 - C45-76 (THW)
    Always
    Below 1 Ω
    C71-1 - C45-75 (E2)
    Always
    Below 1 Ω
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 - C46-76 (THW)
    Always
    Below 1 Ω
    C71-1 - C46-75 (E2)
    Always
    Below 1 Ω



OK
Go to step 9

NG
Go to step 8
4. READ VALUE USING INTELLIGENT TESTER (CHECK FOR SHORT IN WIRE HARNESS)

  1. A166688E02
    Disconnect the ECT sensor connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the value.

    OK:
    -40°C (-40°F)



OK
Go to step 10

NG
Go to step 5
5. CHECK HARNESS AND CONNECTOR (ENGINE COOLANT TEMPERATURE SENSOR - ECM)

  1. A185903E03
    Disconnect the ECT sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 or C45-76 (THW) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    C71-2 or C46-76 (THW) - Body ground
    Always
    10 kΩ or higher



NG
Go to step 8
OK


6. REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
7. CONFIRM GOOD CONNECTION TO SENSOR. IF OK, REPLACE ENGINE COOLANT TEMPERATURE SENSOR
  1. Replace the engine coolant temperature sensor (Click here).



NEXT
Go to step 11
8. REPAIR OR REPLACE HARNESS OR CONNECTOR


NEXT
Go to step 11
9. CONFIRM GOOD CONNECTION TO ECM. IF OK, REPLACE ECM
  1. Replace the ECM (Click here).



NEXT
Go to step 11
10. REPLACE ENGINE COOLANT TEMPERATURE SENSOR
  1. Replace the engine coolant temperature sensor (Click here).


NEXT


11. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the intelligent tester to the DLC3.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON for 1 second.

  1. Enter the following menus: Powertrain / Engine / DTC.

  1. Confirm that the DTC is not output again.


NEXT

END


← P0115 Engine Coolant Temperature Circuit (+ P0117, P0118) (Sep 2011 – Dec 2011)P0116 Engine Coolant Temperature Circuit Range / Performance Problem (Sep 2011 – Dec 2011) →