P0405 Exhaust Gas Recirculation Sensor "A" Circuit Low
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- P0406 Exhaust Gas Recirculation Sensor "A" Circuit High
- P0407 Exhaust Gas Recirculation Sensor "B" Circuit Low
- P0408 Exhaust Gas Recirculation Sensor "B" Circuit High
DESCRIPTION
The EGR valve position sensor is mounted on the EGR valve and used for detecting the lift amount of the valve. The lift amount detected by the sensor is provided to the ECM as feedback. The ECM then regulates the lift amount of the valve in accordance with engine running conditions.| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Engine switch on (IG) for 5 seconds |
EGR valve position sensor output voltage is less than 0.1 V for 5 seconds. (1 trip detection logic) |
|
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Engine switch on (IG) for 5 seconds |
EGR valve position sensor output voltage is more than 4.9 V for 5 seconds. (1 trip detection logic) |
|
MONITOR DESCRIPTION
When the output voltage of the EGR valve position sensor deviates from the normal operating range of 0.1 to 4.9 V for more than 5 seconds, the ECM interprets this as a malfunction of the sensor circuit, and illuminates the MIL.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here).
- After replacing the fuel supply pump assembly, the ECM needs initialization (Click here).
- After replacing an injector assembly, the ECM needs registration (Click here).
- Inspect the fuses of circuits related to this system before performing the following inspection procedure.
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
| 1. CHECK HARNESS AND CONNECTOR (EGR VALVE POSITION SENSOR - ECM) |
Disconnect the No. 1 or No. 2 EGR valve assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
No. 1 (LHD) Tester Connection
Condition
Specified Condition
C87-3 (VC) - C45-91 (VC)
Always
Below 1 Ω
C87-4 (EGLS) - C45-88 (EGLS)
Always
Below 1 Ω
C87-2 (E2) - C45-92 (E2)
Always
Below 1 Ω
C87-3 (VC) or C45-91 (VC) - Body ground
Always
10 kΩ or higher
C87-4 (EGLS) or C45-88 (EGLS) - Body ground
Always
10 kΩ or higher
No. 2 (LHD) Tester Connection
Condition
Specified Condition
C88-3 (VC) - C45-91 (VC)
Always
Below 1 Ω
C88-4 (EGS2) - C45-89 (EGS2)
Always
Below 1 Ω
C88-2 (E2) - C45-92 (E2)
Always
Below 1 Ω
C88-3 (VC) or C45-91 (VC) - Body ground
Always
10 kΩ or higher
C88-4 (EGS2) or C45-88 (EGLS) - Body ground
Always
10 kΩ or higher
No. 1 (RHD) Tester Connection
Condition
Specified Condition
C87-3 (VC) - C46-91 (VC)
Always
Below 1 Ω
C87-4 (EGLS) - C46-88 (EGLS)
Always
Below 1 Ω
C87-2 (E2) - C46-92 (E2)
Always
Below 1 Ω
C87-3 (VC) or C46-91 (VC) - Body ground
Always
10 kΩ or higher
C87-4 (EGLS) or C46-88 (EGLS) - Body ground
Always
10 kΩ or higher
No. 2 (RHD) Tester Connection
Condition
Specified Condition
C88-3 (VC) - C46-91 (VC)
Always
Below 1 Ω
C88-4 (EGS2) - C46-89 (EGS2)
Always
Below 1 Ω
C88-2 (E2) - C46-92 (E2)
Always
Below 1 Ω
C88-3 (VC) or C46-91 (VC) - Body ground
Always
10 kΩ or higher
C88-4 (EGS2) or C46-89 (EGS2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK ECM TERMINAL VOLTAGE (VC TERMINAL) |
Disconnect the No. 1 or No. 2 EGR valve assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
No. 1 Tester Connection
Switch Condition
Specified Condition
C87-3 (VC) - C87-2 (E2)
Engine switch on (IG)
4.5 to 5.5 V
No. 2 Tester Connection
Switch Condition
Specified Condition
C88-3 (VC) - C88-2 (E2)
Engine switch on (IG)
4.5 to 5.5 V
Text in Illustration *A
No. 1
*B
No. 2
*a
Front view of wire harness connector
(to EGR valve assembly)
|
|
||||
| OK | |
| 3. REPLACE EGR VALVE ASSEMBLY |
- Replace the No. 1 EGR valve assembly (Click here).
- Replace the No. 2 EGR valve assembly (Click here).
|
|
||||
| 4. REPLACE ECM |
Replace the ECM (Click here).
|
|
||||
| 5. REPAIR OR REPLACE HARNESS OR CONNECTOR |
Repair or replace the harness or connector.
| NEXT | |
| 6. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the GTS to the DLC3.
Clear the DTCs (Click here).
Turn the engine switch off.
Turn the engine switch on (IG) for 5 seconds.
Enter the following menus: Engine and ECT / Trouble Codes.
Confirm that the DTC is not output again.
| NEXT | ||
| ||
