2011-2013 Land Cruiser · Service Manual Steering

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

NOTICE:
When installing parts, coat the parts indicated by arrows with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL
  1. Coat the lip of a new oil seal with power steering fluid.

  1. C161397E01
    Using SST and a press, press in the oil seal.
    SST
    09950-60010   (09951-00320)
    09950-70010   (09951-07150)

    NOTICE:
    1. Do not mistake the direction of the oil seal.
    2. Do not damage the oil seal.


2. INSTALL VANE PUMP SHAFT BEARING

  1. C162116
    Using a brass bar and hammer, tap on a new snap ring.

    NOTICE:
    Be careful not to damage the shaft.

  1. C162117
    Using a press, press in the shaft into the bearing.

    NOTICE:
    Be careful not to damage the bearing.


3. INSTALL VANE PUMP SHAFT WITH VANE PUMP SHAFT BEARING
  1. Temporarily install the rear housing to the front housing.

  1. C161398E01
    Using SST and a press, press in the shaft with bearing into the front housing.
    SST
    09632-36010  

  1. Using a screwdriver, install a new snap ring into the front housing.


4. INSTALL VANE PUMP GEAR

  1. C162119E01
    Using SST and a press, press in the gear to the shaft.
    SST
    09950-60010   (09951-00420)
    09950-70010   (09951-07150)

  1. Remove the rear housing from the front housing.


5. INSTALL VANE PUMP FRONT SIDE PLATE

  1. C162123
    Coat a new O-ring with power steering fluid and install it into the front housing.

  1. C162156
    Coat a new O-ring with power steering fluid and install it onto the front side plate.

  1. C161399E01
    Align the notch of the front side plate with the notch of the front housing, and install the front side plate.

    NOTICE:
    Make sure that the front side plate is installed facing in the correct direction.


6. INSTALL VANE PUMP CAM RING

  1. C161400E01
    Align the notch of the cam ring with the notch of the front side plate, and install the cam ring with the inscribed mark facing upward.

    NOTICE:
    Make sure that the cam ring is installed facing in the correct direction.


7. INSTALL VANE PUMP ROTOR AND VANE PUMP PLATE
  1. Install the rotor with the inscribed mark facing upward.

  1. Coat the 10 vane pump plates with power steering fluid.

  1. C161401E01
    Install the 10 vane pump plates with the round end facing upward.

    NOTICE:
    Make sure that the 10 vane pump plates are installed facing in the correct direction.


8. INSTALL REAR VANE PUMP HOUSING
  1. Coat a new O-ring with power steering fluid and install it onto the rear housing.

  1. C162122E01
    Align the straight pin of the rear housing with the notches of the cam ring, front side plate and front housing.

    NOTICE:
    Make sure that the O-ring is not protruding anywhere when installing the vane pump rear housing.

  1. C162098
    Install the rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


9. INSTALL FLOW CONTROL VALVE

C179804
  1. Coat the flow control valve with power steering fluid.

  1. Install the compression spring and flow control valve to the front housing.

    NOTICE:
    Do not mistake the direction of the control valve.

  1. Coat a new O-ring with power steering fluid and install it onto the pressure port union.

  1. Install the pressure port union to the front housing.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }

  1. Install the pressure feed union with the bolt to the pressure port union.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }


10. INSTALL POWER STEERING SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the suction port union.

  1. Install the suction port union to the vane pump with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


11. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install a service bolt.

    Recommended service bolt:
    Thread diameter:
    10 mm (0.394 in.)
    Thread pitch:
    1.25 mm (0.0493 in.)
    Bolt length:
    50 mm (1.97 in.)

  1. C178182E01
    Using a torque wrench, measure the pump rotating torque.

    Standard rotating torque:
    0.27 N*m (2.8 kgf*cm, 2.4 in.*lbf) or less

    If the rotating torque is not as specified, check the oil seal.

← INSPECTION (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →