2011-2013 Land Cruiser · Service Manual Steering

REASSEMBLY

Removal / installation · Vehicles built from Jan 2012

NOTICE:
When installing parts, coat the parts indicated by arrows with power steering fluid (Click here).


1. INSTALL VANE PUMP HOUSING OIL SEAL
  1. Coat the lip of a new oil seal with power steering fluid.

  1. C228151E01
    Using SST and a press, press in the oil seal.
    SST
    09950-60010   (09951-00280)
    09950-70010   (09951-07100)

    NOTICE:
    Make sure that the oil seal is installed facing in the correct direction as shown in the illustration.


2. INSTALL VANE PUMP SHAFT WITH VANE PUMP PULLEY
  1. Coat the inside surface of the bushing in the vane pump front housing with power steering fluid.

  1. C114703E02
    Gradually insert the vane pump shaft with vane pump pulley.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    1. Do not damage the lip of the oil seal in the front housing.
    2. Wrap protective tape around the spline of the vane pump shaft with vane pump pulley in order to prevent damage to the oil seal.


3. INSTALL VANE PUMP FRONT SIDE PLATE

  1. C132035
    Coat a new O-ring with power steering fluid and install it into the front housing.

  1. C107035
    Coat a new O-ring with power steering fluid and install it onto the front side plate.

  1. C132040E03
    Align the notch of the front side plate with the notch of the front housing, and install the front side plate.
    Text in Illustration 
    *a
    Align

    NOTICE:
    Make sure that the front side plate is installed facing in the correct direction.


4. INSTALL VANE PUMP CAM RING
  1. Coat the vane pump cam ring with power steering fluid.

  1. C139139E03
    Align the notch of the cam ring with the notch of the front side plate, and install the cam ring with the inscribed mark facing upward.
    Text in Illustration 
    *a
    Align
    *b
    Inscribed Mark

    NOTICE:
    Make sure that the cam ring is installed facing in the correct direction.


5. INSTALL VANE PUMP ROTOR
  1. Coat the vane pump rotor with power steering fluid.

  1. C107038
    Install the vane pump rotor.

    HINT:
    The vane pump rotor can be installed in both directions.

  1. Coat the 10 vane pump plates with power steering fluid.

  1. C141370E02
    Install the vane pump plates with the round end facing outward.
    Text in Illustration 
    *a
    Round End
    *b
    Outward

    NOTICE:
    Make sure that the vane pump plates are installed facing in the correct direction.


6. INSTALL VANE PUMP SHAFT SNAP RING

  1. D030336E01
    Using a screwdriver and snap ring expander, install a new shaft snap ring onto the vane pump shaft.

    NOTICE:
    1. Do not expand the shaft snap ring any further than needed.
    2. Make sure that the shaft snap ring is completely fit into the groove.
    3. Do not damage the vane pump rotor and shaft.


7. INSTALL VANE PUMP REAR HOUSING

  1. C107040
    Coat a new O-ring with power steering fluid and install it onto the rear housing.

  1. C136780E05
    Align the straight pin of the rear housing with the notches of the cam ring, front side plate and front housing.
    Text in Illustration 
    *a
    Align

    NOTICE:
    Make sure that the O-ring is not protruding anywhere when installing the vane pump rear housing.

  1. C107024
    Install the rear housing with the 4 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }


8. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install a service bolt.

    Recommended service bolt:
    Thread diameter:
    10 mm (0.394 in.)
    Thread pitch:
    1.25 mm (0.0492 in.)
    Bolt length:
    50 mm (1.97 in.)

  1. C053369E13
    Using a torque wrench, measure the pump rotating torque.

    Standard rotating torque:
    0.3 N*m (3 kgf*cm, 3 in.*lbf) or less

    Text in Illustration 
    *1
    Service Bolt
    If the rotating torque is not as specified, check the vane pump housing oil seal.


9. INSTALL FLOW CONTROL VALVE ASSEMBLY

  1. C228110
    Coat the flow control valve, pressure port union and spring with power steering fluid.

  1. Install the compression spring and flow control valve to the front housing.

    NOTICE:
    Do not mistake the direction of the control valve.

  1. Coat a new O-ring with power steering fluid and install it onto the pressure port union.

  1. Install the pressure port union to the front housing.

    Torque:
    69 N*m{ 704 kgf*cm , 51 ft.*lbf }


10. FIX VANE PUMP ASSEMBLY

  1. C158820E01
    Using SST, fix the vane pump in a vise.
    SST
    09630-00014   (09631-00132)


11. INSTALL POWER STEERING SUCTION PORT UNION
  1. Coat a new O-ring with power steering fluid and install it to the suction port union.

  1. C158821
    Install the suction port union to the vane pump with the bolt.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

← INSPECTION (from Jan 2012)INSTALLATION (from Jan 2012) →