2011-2013 Land Cruiser · Service Manual Drivetrain

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL OIL COOLER ASSEMBLY

C171508E01
  1. Connect the oil cooler inlet hose and outlet hose.

  1. C167870
    Install the rear transmission oil cooler air duct with the 4 bolts, and then install the air cooled oil cooler tube to the transmission oil cooler air duct with the bolt.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }

  1. C167869E01
    Temporarily put the oil cooler on the radiator support.

    NOTICE:
    Securely attach the 2 claws of the oil cooler into the holes of the radiator support.

  1. Install the 4 bolts in the sequence shown in the illustration.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


2. INSTALL TRANSMISSION OIL COOLER AIR DUCT

C167867E01
  1. Install the oil cooler air duct with the 4 bolts in the sequence shown in the illustration.

    Torque:
    4.9 N*m{ 50 kgf*cm , 43 in.*lbf }


3. INSTALL OIL COOLER TUBE SUB-ASSEMBLY (for 2UZ-FE)

C172416E02
  1. Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


4. INSTALL OIL COOLER TUBE SUB-ASSEMBLY (for 1GR-FE)

C248667E01
  1. Temporarily install the oil cooler tube to the fan shroud with bolt A. Install bolt B and tighten it to the specified torque. Then tighten bolt A to the specified torque.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


5. CONNECT INLET NO. 4 OIL COOLER HOSE (for 2UZ-FE)

C172434E01
  1. Connect the inlet oil cooler hose as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.


6. CONNECT INLET NO. 4 OIL COOLER HOSE (for 1GR-FE)

C172435E01
  1. Connect the inlet oil cooler hose as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.


7. CONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE (for 2UZ-FE)

C173927E01
  1. Connect the oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.


8. CONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE (for 1GR-FE)

C167878
C248671
  1. Connect the 2 transmission oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.


9. CONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE (for 2UZ-FE)

C167893E01
  1. w/ Air Cooled Transmission Oil Cooler:

    1. Connect the 2 oil cooler hoses as shown in the illustration.

      NOTICE:
      Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

    2. Pass the hose through the flexible hose clamp and close the clamp shown in the illustration.

  1. w/o Air Cooled Transmission Oil Cooler:

    1. C170800E01
      Connect the 2 oil cooler hoses as shown in the illustration.

      NOTICE:
      Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.


10. CONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE (for 1GR-FE)

C167875E01
  1. Connect the 2 oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration and the paint marks are aligned as shown in the illustration.

  1. Pass the hose through the flexible hose clamp and close the clamp shown in the illustration.


11. CONNECT TRANSMISSION OIL COOLER HOSE (for 2UZ-FE)

C172419E01
  1. Connect the 2 transmission oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.


12. CONNECT TRANSMISSION OIL COOLER HOSE (for 1GR-FE)

C248672E01
  1. Connect the 2 transmission oil cooler hoses as shown in the illustration.

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.


13. ADD AUTOMATIC TRANSMISSION FLUID
  1. Add automatic transmission fluid (Click here).


14. INSTALL HEADLIGHT ASSEMBLY RH (w/ Air Cooled Transmission Oil Cooler)
for Standard: (Click here)
for HID Headlight: (Click here)

15. INSTALL FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Install the fender apron seal with the 4 clips.


16. INSTALL FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Install the fender apron seal with the 3 clips.


17. INSTALL NO. 1 ENGINE UNDER COVER

C173929
  1. Install the under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


18. INSTALL NO. 2 ENGINE UNDER COVER

C173930
  1. Install the under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


19. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


20. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →