2011-2013 Land Cruiser · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


3. REMOVE NO. 2 ENGINE UNDER COVER

C173930
  1. Remove the 6 bolts and under cover.


4. REMOVE NO. 1 ENGINE UNDER COVER

C173929
  1. Remove the 6 bolts and under cover.


5. REMOVE HEADLIGHT ASSEMBLY RH (w/ Air Cooled Transmission Oil Cooler)
for Standard: (Click here)
for HID Headlight: (Click here)

6. REMOVE FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Using a clip remover, remove the 3 clips and fender apron seal.


7. REMOVE FRONT FENDER APRON SEAL REAR RH

  1. A177002
    Using a clip remover, remove the 4 clips and fender apron seal.


8. DISCONNECT TRANSMISSION OIL COOLER HOSE (for 1GR-FE)

C248670
  1. Disconnect the 2 transmission oil cooler hoses.


9. DISCONNECT TRANSMISSION OIL COOLER HOSE (for 2UZ-FE)

C172412E01
  1. Disconnect the 2 transmission oil cooler hoses.


10. DISCONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE (for 1GR-FE)

C248669
  1. Detach the claw to open the flexible hose clamp.

  1. Disconnect the inlet and outlet oil cooler hoses.


11. DISCONNECT INLET NO. 1 OIL COOLER HOSE AND OUTLET NO. 1 OIL COOLER HOSE (for 2UZ-FE)

C172414E01
  1. w/ Air Cooled Transmission Oil Cooler:

    1. Detach the claw to open the flexible hose clamp.

    2. Disconnect the inlet and outlet oil cooler hoses.

  1. w/o Air Cooled Transmission Oil Cooler:

    1. Disconnect the inlet and outlet oil cooler hoses.


12. DISCONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE (for 1GR-FE)

C248668
  1. Disconnect the 2 inlet oil cooler hoses.


13. DISCONNECT INLET NO. 2 OIL COOLER HOSE AND INLET NO. 3 OIL COOLER HOSE (for 2UZ-FE)

C172436E01
  1. Disconnect the 2 inlet oil cooler hoses.


14. DISCONNECT INLET NO. 4 OIL COOLER HOSE (for 1GR-FE)

C172432

15. DISCONNECT INLET NO. 4 OIL COOLER HOSE (for 2UZ-FE)

C172433

16. REMOVE OIL COOLER TUBE (for 1GR-FE)

C248667
  1. Remove the 2 bolts and oil cooler tube.


17. REMOVE OIL COOLER TUBE (for 2UZ-FE)

C172416E01
  1. Remove the 2 bolts and oil cooler tube.


18. REMOVE TRANSMISSION OIL COOLER AIR DUCT

C167867
  1. Remove the 4 bolts and transmission oil cooler air duct.


19. REMOVE OIL COOLER ASSEMBLY

C167868
  1. Remove the 4 bolts and oil cooler.

  1. C167870
    Remove the 5 bolts and transmission oil cooler air duct.

  1. C172417
    Disconnect the oil cooler inlet hose and outlet hose and remove the tube.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →