2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0550 Power Steering Pressure Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The power steering oil pressure sensor is turned on when a power steering wheel load occurs by turning the steering wheel. The ECM regulates the engine idling RPM according to the voltage output of the sensor.
DTC Code
DTC Detection Condition
Trouble Area
P0550
Power steering oil pressure sensor voltage less than 0.28 V, or more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM
P0552
Power steering oil pressure sensor voltage less than 0.28 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM
P0553
Power steering oil pressure sensor voltage more than 4.9 V for 0.5 seconds while engine running.
(1 trip detection logic)
  1. Open or short in power steering oil pressure sensor circuit
  2. Power steering oil pressure sensor
  3. ECM

WIRING DIAGRAM

A162851E08

MONITOR DESCRIPTION

The ECM monitors the sensor voltage and uses this value to regulate the engine idling speed. When the sensor output voltage deviates from the normal operating range, the ECM determines that there is a malfunction in the power steering oil pressure sensor and stores DTC(s).

INSPECTION PROCEDURE

HINT:
  1. If other DTCs relating to different systems that have terminal E2 as the ground terminal are output simultaneously, terminal E2 may have an open circuit.
  2. Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (ECM - POWER STEERING OIL PRESSURE SENSOR)
A182384E04
  1. Disconnect the C45 ECM connector.

  1. Disconnect the C59 power steering oil pressure sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C59-2 (PSP) - C45-72 (PSP)
    Always
    Below 1 Ω
    C59-1 (VC) - C45-67 (VCV1)
    Always
    Below 1 Ω
    C59-3 (E2) - C45-97 (ETHW)
    Always
    Below 1 Ω
    C59-2 (PSP) or C45-72 (PSP) - Body ground
    Always
    10 kΩ or higher
    C59-1 (VC) or C45-67 (VCV1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. REPLACE POWER STEERING OIL PRESSURE SENSOR
  1. Replace the power steering oil pressure sensor (Click here).


NEXT


3. CONFIRM WHETHER DTC OUTPUT RECURS
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0550, P0552 and/or P0553 are output
    A
    No DTC is output
    B



B
END
A

REPLACE ECM (Click here)


← P0504 Brake Switch "A" / "B" Correlation (from Jan 2012)P0550 Power Steering Pressure Sensor Circuit Malfunction (+ P0552, P0553) (from Jan 2012) →