PTC Heater Circuit
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
PTC heater relays are closed in accordance with signals from the air conditioning amplifier assembly and power is supplied to the quick heater assembly installed on the radiator heater unit.WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses and relays for circuits related to this system before performing the following inspection procedure.
| 1. INSPECT PTC HEATER RELAY (PTC HTR1, PTC HTR2, PTC HTR3) |
Remove the PTC heater relays from the engine room relay block and junction block assembly.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied between terminals 1 and 2
10 kΩ or higher
Battery voltage is applied between terminals 1 and 2
Below 1 Ω
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - BATTERY) |
Remove the PTC heater relays from the engine room relay block and junction block assembly.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
PTC HTR1 relay terminal 5 - Body ground
Always
11 to 14 V
PTC HTR2 relay terminal 5 - Body ground
PTC HTR3 relay terminal 5 - Body ground
Text in Illustration *a
Component without relay installed
(Engine Room Relay Block and Junction Block Assembly)
*1
PTC Heater Relay (PTC HTR3)
*2
PTC Heater Relay (PTC HTR2)
*3
PTC Heater Relay (PTC HTR1)
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - AIR CONDITIONING AMPLIFIER AND BODY GROUND) |
Remove the PTC heater relays from the engine room relay block and junction block assembly.
Disconnect the E81 air conditioning amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
PTC HTR1 relay terminal 1 - E81-3 (PTC1)
Always
Below 1 Ω
PTC HTR2 relay terminal 1 - E81-22 (PTC2)
PTC HTR3 relay terminal 1 - E81-4 (PTC3)
PTC HTR1 relay terminal 1 - Body ground
Always
10 kΩ or higher
PTC HTR2 relay terminal 1 - Body ground
PTC HTR3 relay terminal 1 - Body ground
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
PTC HTR1 relay terminal 2 - Body ground
Always
Below 1 Ω
PTC HTR2 relay terminal 2 - Body ground
PTC HTR3 relay terminal 2 - Body ground
|
|
||||
| OK | |
| 4. CHECK HARNESS AND CONNECTOR (PTC HEATER RELAY - QUICK HEATER) |
Remove the PTC heater relays from the engine room relay block and junction block assembly.
Disconnect the E33 quick heater assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
PTC HTR1 relay terminal 3 - E33-2 (B)
Always
Below 1 Ω
PTC HTR2 relay terminal 3 - E33-1 (B)
PTC HTR3 relay terminal 3 - E33-3 (B)
PTC HTR1 relay terminal 3 - Body ground
Always
10 kΩ or higher
PTC HTR2 relay terminal 3 - Body ground
PTC HTR3 relay terminal 3 - Body ground
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (QUICK HEATER - BODY GROUND) |
Disconnect the E34 quick heater assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
E34-1 (E) - Body ground
Always
Below 1 Ω
E34-2 (E) - Body ground
Text in Illustration *a
Front view of wire harness connector
(to Quick Heater Assembly)
|
|
||||
| OK | |
| 6. INSPECT QUICK HEATER ASSEMBLY |
Remove the quick heater assembly (Click here).

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
1 (B) - 1 (E)
Always
Below 1 kΩ
2 (B) - 1 (E)
2 (B) - 2 (E)
3 (B) - 2 (E)
|
|
||||
| OK | |
| 7. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
Remove the air conditioning amplifier assembly with its connectors still connected (Click here).

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
E81-3 (PTC1) - Body ground
Engine idling
Set temperature MAX. HOT
Engine coolant temperature below 65°C (149°F)
Ambient temperature below 10°C (50°F)
Blower switch off → LO level
Below 1 V → 11 to 14 V*
E81-22 (PTC2) - Body ground
E81-4 (PTC3) - Body ground
Text in Illustration *a
Component with harness connected
(Air Conditioning Amplifier Assembly)
- HINT:
- *: After the measurement conditions are met, wait 30 seconds before performing measurements.
|
|
||||
| OK | ||
| ||
