2011-2013 Land Cruiser · Service Manual Steering

B2788 IG2 Signal Malfunction

Diagnostic trouble codes · Vehicles built from Sep 2011

DESCRIPTION

The steering lock ECU determines the on/off status of the engine switch through the IG2 signal circuit.
After receiving an integration relay (IG2 relay) on signal, the steering lock ECU determines that the vehicle is moving.
The steering lock ECU does not lock the steering when it receives the integration relay (IG2 relay) on signal. This prevents the steering from being locked while the vehicle is moving.
The diagnosis information of the steering lock ECU is transmitted to the intelligent tester via the certification ECU (smart key ECU assembly) as the steering lock ECU is not connected to the CAN communication system.
DTC Code
Detection Condition
Trouble Area
B2788
Open or short in IG2 signal circuit
  1. Steering lock actuator assembly (steering lock ECU)
  2. IGN fuse
  3. IG2 MAIN fuse
  4. Integration relay (IG2 relay)
  5. Main body ECU
  6. Harness or connector

WIRING DIAGRAM

A175476E01

INSPECTION PROCEDURE

HINT:
When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:
With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.


1. INSPECT STEERING LOCK ECU
C165193E09
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E26-6 (IG2) - E26-1 (GND)
    Engine switch off
    Below 1 V
    E26-6 (IG2) - E26-1 (GND)
    Engine switch on (IG)
    11 to 14 V

    Result 
    Result
    Proceed to
    Within specified range (for Power tilt and telescopic)
    A
    Outside specified range
    B
    Within specified range (for Manual tilt and telescopic)
    C



B
Go to step 2

C
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)
A

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)

2. INSPECT FUSE (IGN, IG2 MAIN)
  1. Remove the IGN fuse and IG2 MAIN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IGN fuse
    Always
    Below 1 Ω
    IG2 MAIN fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


3. INSPECT INTEGRATION RELAY (IG2 RELAY)
A175471E01
  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1B-8 - 1C-1
    Battery voltage is applied to terminals 1B-6 and 1B-7
    Below 1 Ω
    1B-8 - 1C-1
    Battery voltage is not applied to terminals 1B-6 and 1B-7
    10 kΩ or higher



NG
REPLACE INTEGRATION RELAY (IG2 RELAY)
OK


4. CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)
A175474E01
  1. Disconnect the E26 steering lock ECU connector.

  1. Disconnect the 1B and 1C integration relay connectors.

  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - Body ground
    Always
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E26-6 (IG2) - 1B-8
    Always
    Below 1 Ω
    E26-6 (IG2) or 1B-8 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY (IG2 RELAY) AND BODY GROUND)
A175472E01
  1. Disconnect the E2 main body ECU connector.

  1. Disconnect the 1B integration relay connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-11 (IG2D) - 1B-6
    Always
    Below 1 Ω
    1B-7 - Body ground
    Always
    Below 1 Ω
    E2-11 (IG2D) or 1B-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU


← B2782 Power Source Control ECU Malfunction (from Jan 2012)Steering Lock Motor Drive Power Circuit (Sep 2011 – Dec 2011) →