2011-2013 Land Cruiser · Service Manual Suspension

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. REMOVE STABILIZER CONTROL VALVE PROTECTOR (w/ KDSS)

C172095
  1. Detach the clamp, and disconnect the connector from the protector.

  1. Remove the 3 bolts and protector.


2. OPEN STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE (w/ KDSS)

  1. Using a 5 mm hexagon socket wrench, loosen the lower and upper chamber shutter valves of the stabilizer control with accumulator housing 2.0 to 3.5 turns.

    C175131E01

    NOTICE:
    1. When loosening a shutter valve, make sure that the end protrudes 2 to 3.5 mm (0.0787 to 0.137 in.) from the surface of the block, and do not turn the shutter valve any further.
    2. Do not remove the shutter valves.


3. REMOVE FRONT WHEEL

4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the fender splash shield.


5. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


6. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A238241
    Remove the 10 bolts and No. 1 engine under cover.


7. LOOSEN FRONT NO. 1 STABILIZER BRACKET LH

  1. C177819
    Loosen the 2 bolts of the front stabilizer brackets.


8. LOOSEN FRONT NO. 1 STABILIZER BRACKET RH

  1. C177820
    Loosen the 2 bolts of the front stabilizer brackets.


9. REMOVE FRONT STABILIZER LINK ASSEMBLY LH (w/ KDSS)

  1. C177821
    Remove the 2 bolts, nut and stabilizer link.


10. REMOVE FRONT STABILIZER LINK ASSEMBLY LH (w/o KDSS)

  1. C173240
    Remove the bolt, nut and stabilizer link.


11. REMOVE FRONT STABILIZER LINK ASSEMBLY RH

  1. C175802
    Remove the bolt, nut and stabilizer link.

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.


12. DISCONNECT SKID CONTROL SENSOR WIRE

C173472E01
  1. Remove the bolt and nut, and disconnect the sensor wire from the steering knuckle and suspension upper arm.


13. DISCONNECT STEERING KNUCKLE LH

  1. C178724
    Support the front suspension lower arm LH with a jack.

  1. Remove the clip and the nut.

  1. C155977E01
    Using SST, disconnect the upper ball joint from the steering knuckle.
    SST
    09628-62011  

    NOTICE:
    Do not damage the ball joint dust cover.


14. DISCHARGE SUSPENSION FLUID PRESSURE (w/ Active Height Control)

  1. C172938
    Connect a hose to the bleeder plug for the height control accumulator and loosen the bleeder plug.

  1. Discharge the suspension fluid pressure.

  1. After the fluid pressure has dropped and oil has drained out, tighten the bleeder plug and remove the hose.

    Torque:
    6.9 N*m{ 70 kgf*cm , 61 in.*lbf }


15. REMOVE FRONT FENDER APRON SEAL LH (w/ Active Height Control)

  1. C173474
    Using a clip remover, remove the 4 clips and apron seal.


16. REMOVE FRONT FENDER APRON SEAL REAR LH (w/ Active Height Control)

  1. C173476
    Using a clip remover, remove the 4 clips and apron seal.


17. DISCONNECT NO. 2 SUSPENSION CONTROL PRESSURE HOSE (w/ Active Height Control)

  1. C173241
    Remove the 2 bolts and disconnect the pressure hose from the shock absorber.


18. REMOVE FRONT SHOCK ABSORBER WITH COIL SPRING LH

C155964
  1. Remove the nut from the shock absorber lower side.

    NOTICE:
    To prevent the shock absorber with coil spring from falling, leave the bolt inserted.

  1. C173242
    Remove the 4 nuts.

  1. Remove the bolt (lower side) and shock absorber with coil spring.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →