2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

SYSTEM DESCRIPTION

Troubleshooting · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


DISC PLAYER OUTLINE
  1. A CD player uses a laser pickup to read digital signals recorded on CDs. By converting the digital signals to analog, music and other content can be played.

    CAUTION:
    Do not look directly at the laser pickup because the CD player uses an invisible laser beam. Be sure to operate the player only as instructed.

    NOTICE:
    1. Do not disassemble any part of the CD player.
    1. Do not apply oil to the CD player.
    1. Do not insert anything but a CD into the CD player.

  2. Usable discs

    1. CD player
      E119759

  3. Precautions for handling discs

    NOTICE:
    1. Copy-controlled CDs cannot be used.
    2. Some CD-Rs and CD-RWs are not playable as a result of: 1) the type of recording method used, 2) the type of disc, 3) scratches, 4) contamination, or 5) the disc being in the vehicle for an extended amount of time, leading to deterioration.
    3. CD-Rs and CD-RWs that have not been finalized cannot be played.
    4. When handling a disc, be careful not to put fingerprints, stains or scratches on the disc.
    5. When holding a disc, pinch the center hole and edge of the disc with your fingers. Face the printed side upward.
    6. If a disc is ejected by pressing the eject button and left partially ejected for an extended period of time, the disc may become deformed and unusable.
    7. A disc may not be able to be ejected or the player may become damaged if: 1) cellophane tape, stickers, CD-R labels or rental CD labels are attached; or 2) residue from removed tape, stickers or labels remains.
    8. Avoid direct sunlight when storing discs as they may become deformed and unusable.
    9. Do not use uniquely-shaped discs as they may damage the player.
    10. Do not use discs where part of the recording surface is transparent or translucent. If used, the disc may become unable to be inserted, ejected and played normally.

    HINT:
    1. Just as condensation fogs the vehicle windows during wet or cold weather, condensation may also form inside the player. If condensation forms, CD skipping or playback stoppage may occur. Ventilate or dehumidify the vehicle for a while before using the player.
    2. If the player vibrates severely due to driving on a rough road, the CD may skip.

  4. Cleaning

    NOTICE:
    Do not use lens cleaner when cleaning the player, as it may damage the pickup part of the player.


    1. I100151
      To clean dirty discs, use a dry, soft cloth such as those used for glasses with plastic lenses. Lightly wipe radially from the center of the disc.

      NOTICE:
      1. Pressing the disc roughly with your hand or scrubbing with a hard cloth may scratch the disc surface.
      2. Using record spray, anti-static agents, alcohol, benzene, thinner or other solvents, and chemical cloths on a disc will damage the disc and may make the disc unusable.


MP3 OUTLINE
  1. Playable MP3 file standards

    Compatible standard
    MP3 (MPEG1 LAYER3, MPEG2 LSF LAYER3)
    Compatible sampling frequency
    1. MPEG1 LAYER3: 32, 44.1, 48 (kHz)
    2. MPEG2 LSF LAYER3: 16, 22.05, 24 (kHz)
    Compatible bit rate
    1. MPEG1 LAYER3: 64, 80, 96, 112, 128, 160, 192, 224, 256, 320 (kbps)
    2. MPEG2 LSF LAYER3: 64, 80, 96, 112, 128, 144, 160 (kbps)
    3. Compatible with VBR
    Compatible channel mode
    Stereo, joint stereo, dual channel, monaural

  2. ID3 tag

    1. Additional textual information called ID3 tags can be input to MP3 files. Information such as song titles and artist names can be stored.

      HINT:
      This player is compatible with the ID3 tags of ID3 Ver. 1.0 and 1.1, and ID3 Ver. 2.2 and 2.3. (Number of characters complies with ID3 Ver. 1.0 and 1.1).

  3. Usable media

    1. Only CD-ROMs, CD-Rs (CD-Recordable), and CD-RWs (CD-ReWritable) can be used to play MP3 files.

      NOTICE:
      1. CD-Rs and CD-RWs are more easily affected by a hot and humid environment than discs used for normal audio CDs. For this reason, some CD-Rs and CD-RWs may not be playable.
      2. If there are fingerprints or scratches on the disc, the disc may not be playable or the CD may skip.
      3. Some CD-Rs and CD-RWs deteriorate if they are left in the cabin for a long time.
      4. Keep CD-Rs and CD-RWs in a storage case that is non-transparent.

  4. Usable media format

    1. Usable media format

      Disc format
      CD-ROM Mode 1, CD-ROM XA Mode 2 Form1
      File format
      ISO9660 Level 1 and Level 2 (Joliet, Romeo)

      HINT:
      1. As for MP3 files written in any format other than those above, the contents of the files may not be playable or the file names or folder names may not be displayed correctly.
      2. This player is compatible with multi-session discs and can play CD-Rs and CD-RWs on which MP3 files are added. However, only the first session can be played.
      3. Discs whose first session includes both music data and MP3 format data cannot be played.

    2. Standards and restrictions

      Maximum directory levels
      8 levels
      Maximum number of characters for a folder name/file name
      32 characters
      Maximum number of folders
      192 (Including empty folders, root folders, and folders that do not contain MP3 files)
      Maximum number of files in a disc
      255 (Including non-MP3 files)

  5. File names

    1. Only files with an extension of ".mp3" can be recognized and played as MP3 files.

    2. Save MP3 files with an extension of ".mp3".

      NOTICE:
      If saving non-MP3 files with an extension of ".mp3", those files are wrongly recognized as MP3 files and played. A loud noise may occur and damage to the speaker may result.


CASSETTE TAPE PLAYER OUTLINE

  1. E119304E03
    Tape Player / Head Cleaning:

    1. Raise the cassette door with your finger. Using a pencil or similar object, push in the guide.

    2. Using a cleaning pen or cotton applicator soaked in cleaner, clean the head surface, pinch rollers and capstans.


AVC-LAN DESCRIPTION

  1. What is AVC-LAN?
    AVC-LAN, an abbreviation for "Audio Visual Communication Local Area Network", is a united standard developed by the manufacturers in affiliation with Toyota Motor Corporation. This standard pertains to audio and visual signals as well as switch and communication signals.
    E145821E02

  2. Purpose:
    Recently, car audio systems have rapidly developed and the functions have vastly changed. The conventional car audio system is being integrated with multimedia interfaces similar to those in navigation systems. At the same time, customers are demanding higher quality from their audio systems. This is an overview of the standardization background. The specific purposes are as follows:

    1. To solve sound problems, etc. caused by using components of different manufacturers through signal standardization.

    2. To allow each manufacturer to concentrate on developing the products they do best. From this, reasonably priced products can be produced.

      HINT:
      1. If a short to +B or short to ground is detected in the AVC-LAN circuit, communication is interrupted and the audio system will stop functioning.
      2. The radio receiver contains a resistor that is necessary to enable communication on the different AVC-LAN circuits.
      3. The car audio system with an AVC-LAN circuit has a diagnostic function.
      4. Each component has a specified number (3-digit) called a physical address. Each function has a number (2-digit) called a logical address.


COMMUNICATION SYSTEM OUTLINE
  1. Components of the audio system communicate with each other via the AVC-LAN.

  2. The master component of the AVC-LAN is a radio receiver with a 60 to 80 Ω resistor. This is essential for communication.

  3. If a short circuit or open circuit occurs in the AVC-LAN circuit, communication is interrupted and the audio system will stop functioning.


DIAGNOSTIC FUNCTION OUTLINE
  1. The audio system has a diagnostic function. The result is indicated on the master unit.

  2. A 3-digit hexadecimal component code (physical address) is allocated to each component on the AVC-LAN. Using this code, the component can be displayed in the diagnostic function.


DIAGNOSTIC TROUBLE CHART
Terms
Definitions
Physical address (component code)
  1. Three-digit code (in hexadecimals) given to each component of the AVC-LAN.
  2. Individual symbols provided corresponding to each function.
Logical address
Two-digit code (in hexadecimals) given to each function and component unit in each component of AVC-LAN.

HINT:
Titles for each unit below are stated in the following order: physical address (part name).

  1. 190 (RADIO RECEIVER)

    Logical Address: 01 (Communication Control) 
    DTC
    Diagnostic Item
    Diagnostic Content
    Troubleshooting
    D5*1
    Absence of Registration Unit
    When either condition below is met:
    1. Device that the sub-code shows is (was) disconnected from the system when turning ignition switch to ON or ACC.
    2. Communication condition with the device that the code shows cannot be obtained when the engine starts.
    1. Check harness of power supply system of component shown by sub-code.
    2. Check harness of communication system of component shown by sub-code.
    D8*2
    No Response for Connection Check
    Device indicated by the sub-code is (was) disconnected from the system after the engine starts.
    1. Check harness of power supply system of component shown by sub-code.
    2. Check harness of communication system of component shown by sub-code.
    D9*1
    Last Mode Error
    Device that had functioned before the engine stopped is (was) disconnected from the system when the ignition switch is (was) in ON or ACC.
    1. Check harness of power supply system of component shown by sub-code.
    2. Check harness of communication system of component shown by sub-code.
    DA
    No Response Against ON/OFF Command
    When either condition below is met:
    1. No response is identified when changing modes.
    2. Detected when the sound and image do not change by switch operation.
    1. Check harness of power supply system of component shown by sub-code.
    2. Check harness of communication system of component shown by sub-code.
    3. If error occurs again, replace component shown by sub-code.
    DB*1
    Mode Status Error
    Dual alarm is detected.
    1. Check harness of power supply system of component shown by sub-code.
    2. Check harness of communication system of component shown by sub-code.
    DC*3
    Transmission Error
    Transmission to the component shown by the sub-code failed. (Detecting this DTC does not always mean an actual failure).
    If same sub-code is recorded in other components, check harness of power supply and communication system of all components shown by code. If not, delete DTCs and recheck.
    DE*4
    Slave Reset
    Code is stored when the slave device has been disconnected after the engine starts.
    1. Check harness of power supply system of component shown by sub-code.
    2. Check harness of communication system of component shown by sub-code.
    E1*1
    Voice Processing Device ON Error
    AMP device records that the AMP output does not function even while the source device operates.
    1. Check harness of power supply system of component shown by sub-code.
    2. Check harness of communication system of component shown by sub-code.
    E4*1
    Multiple Frame Incomplete
    Multiple frame transmission is incomplete.
    Since this DTC is provided for engineering purposes, it may be detected when no actual failure exists.

    HINT:
    *1: Even if no failure is detected, a trouble code may be recorded depending on the battery condition or engine start voltage.
    *2: If the power connector is disconnected after the engine starts, this code is recorded after 180 seconds.
    *3: This code may be stored if the engine is started, idled for 60 seconds and then started again.
    *4: This code may be stored if an engine start is attempted while the engine is running.

    Logical Address: 63 (in-dash CD Changer) 
    DTC
    Diagnosis Item
    Diagnosis Content
    Troubleshooting
    42
    Disc cannot be Read
    Disc cannot be read.
    1. Inspect CD.
    2. Replace radio receiver.
    44
    CD Abnormal
    Operation error in the CD mechanism.
    Replace radio receiver.
    47
    High Temperature
    A sensor detects that the CD unit temperature is high.
    Put vehicle in shade and allow it to cool down with ignition switch off, and then recheck for DTCs.
    48
    Excess Current
    Excess current is present in the CD changer.
    Replace radio receiver.

← SYSTEM DIAGRAM (from Jan 2012)SYSTEM DESCRIPTION (from Jan 2012) →