2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSPECTION

Inspection · Vehicles built from Sep 2011


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for RH Side)

  1. B184771E06
    Check the windshield wiper switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch (w/o Rain Sensor) 
      Tester Connection
      Switch Condition
      Specified Condition
      E16-1 (+S) - E16-3 (+1)
      INT
      Below 1 Ω
      OFF
      E16-2 (+B) - E16-3 (+1)
      MIST
      LO
      E16-2 (+B) - E16-4 (+2)
      HI

      If the result is not as specified, replace the windshield wiper switch assembly.

      Standard Resistance:
      Front Wiper Switch (w/ Rain Sensor) 
      Tester Connection
      Switch Condition
      Specified Condition
      E16-1 (+S) - E16-3 (+1)
      AUTO
      Below 1 Ω
      OFF
      E16-2 (+B) - E16-3 (+1)
      MIST
      LO
      E16-2 (+B) - E16-4 (+2)
      HI

      If the result is not as specified, replace the windshield wiper switch assembly.

  1. Check the front washer switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E15-3 (WF)
      On
      Below 1 Ω
      Off
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch assembly.

  1. Check the intermittent operation.

    1. Connect the voltmeter positive (+) lead to terminal E16-3 (+1) and the negative (-) lead to terminal E15-2 (EW).

    2. Connect the battery positive (+) lead to terminal E16-2 (+B) and the negative (-) lead to terminal E15-2 (EW) and E16-1 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the battery positive (+) lead to terminal E16-1 (+S) for 5 seconds.

    5. Connect the battery negative (-) lead to terminal E16-1 (+S). Operate the intermittent wiper relay and check the voltage between terminals E16-3 (+1) and E15-2 (EW).

      Standard Voltage:
      Refer to the illustration below.


      E157470E06

      B278090E02
      If the result is not as specified, replace the switch assembly.

  1. Check the front washer operation.

    1. Turn the wiper switch OFF.

    2. Connect the battery positive (+) lead to terminal E16-2 (+B) and the negative (-) lead to terminals E16-1 (+S) and E15-2 (EW).

    3. Connect the voltmeter positive (+) lead to E16-3 (+1) and the negative (-) lead to terminal E15-2 (EW).

    4. Turn the washer switch ON and OFF, and check the voltage between terminals E16-3 (+1) and E15-2 (EW).

      OK:
      Refer to the illustration below.


      E157493E10

      E157493E08
      If the result is not as specified, replace the switch assembly.

  1. B184771E04
    Check the rear wiper switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Rear Wiper Switch (w/ Rear Wiper Intermittent Function) 
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E15-6 (C1R)
      LO
      Below 1 Ω
      E15-2 (EW) - E15-7 (+1R)
      HI
      E15-2 (EW) - E15-6 (C1R)
      OFF
      10 kΩ or higher
      E15-2 (EW) - E15-7 (+1R)

      If the result is not as specified, replace the windshield wiper switch assembly.

      Standard Resistance:
      Rear Wiper Switch (w/o Rear Wiper Intermittent Function) 
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E15-7 (+1R)
      ON
      Below 1 Ω
      E15-2 (EW) - E15-7 (+1R)
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch assembly.

  1. Check the rear washer switch.

    1. Measure the resistance of the switch.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E16-5 (WR)
      On
      Below 1 Ω
      Off
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch assembly.


INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (for LH Side)

  1. B189269E01
    Check the windshield wiper switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Front Wiper Switch (w/o Rain Sensor) 
      Tester Connection
      Switch Condition
      Specified Condition
      E16-4 (+S) - E16-2 (+1)
      INT
      Below 1 Ω
      OFF
      E16-3 (+B) - E16-2 (+1)
      MIST
      LO
      E16-3 (+B) - E16-1 (+2)
      HI

      If the result is not as specified, replace the windshield wiper switch assembly.

      Standard Resistance:
      Front Wiper Switch (w/ Rain Sensor) 
      Tester Connection
      Switch Condition
      Specified Condition
      E16-4 (+S) - E16-2 (+1)
      AUTO
      Below 1 Ω
      OFF
      E16-3 (+B) - E16-2 (+1)
      MIST
      LO
      E16-3 (+B) - E16-1 (+2)
      HI

      If the result is not as specified, replace the windshield wiper switch assembly.

  1. Check the front washer switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E15-1 (WF)
      On
      Below 1 Ω
      Off
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch assembly.

  1. Check the intermittent operation.

    1. Connect the voltmeter positive (+) lead to terminal E16-2 (+1) and the negative (-) lead to terminal E15-2 (EW).

    2. Connect the battery positive (+) lead to terminal E16-3 (+B) and the negative (-) lead to terminal E15-2 (EW) and E16-4 (+S).

    3. Turn the wiper switch to the INT position.

    4. Connect the battery positive (+) lead to terminal E16-4 (+S) for 5 seconds.

    5. Connect the battery negative (-) lead to terminal E16-4 (+S). Operate the intermittent wiper relay and check the voltage between terminals E16-2 (+1) and E15-2 (EW).

      Standard Voltage:
      Refer to the illustration below.


      E157470E07

      B278090E04
      If the result is not as specified, replace the switch assembly.

  1. Check the front washer operation.

    1. Turn the wiper switch OFF.

    2. Connect the battery positive (+) lead to terminal E16-3 (+B) and the negative (-) lead to terminals E16-4 (+S) and E15-2 (EW).

    3. Connect the voltmeter positive (+) lead to E16-2 (+1) and the negative (-) lead to terminal E15-2 (EW).

    4. Turn the washer switch ON and OFF, and check the voltage between terminals E16-2 (+1) and E15-2 (EW).

      OK:
      Refer to the illustration below.


      E157493E09
      If the result is not as specified, replace the windshield wiper switch assembly.

  1. B189269E04
    Check the rear wiper switch.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Rear Wiper Switch (w/ Rear Wiper Intermittent Function) 
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E15-5 (C1R)
      LO
      Below 1 Ω
      E15-2 (EW) - E15-4 (+1R)
      HI
      E15-2 (EW) - E15-5 (C1R)
      OFF
      10 kΩ or higher
      E15-2 (EW) - E15-4 (+1R)

      If the result is not as specified, replace the windshield wiper switch assembly.

      Standard Resistance:
      Rear Wiper Switch (w/o Rear Wiper Intermittent Function) 
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E15-4 (+1R)
      ON
      Below 1 Ω
      E15-2 (EW) - E15-4 (+1R)
      OFF
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch assembly.

  1. Check the rear washer switch.

    1. Measure the resistance of the switch.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      E15-2 (EW) - E16-10 (WR)
      On
      Below 1 Ω
      Off
      10 kΩ or higher

      If the result is not as specified, replace the windshield wiper switch assembly.

← REMOVAL (from Sep 2011)INSTALLATION (from Sep 2011) →