TERMINALS OF ECU
System information · Vehicles built from Sep 2011
| CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for LHD) |
![]() ![]() |
Disconnect the I12 front power window regulator motor assembly LH connector.
Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I12-2 (B) - I12-1 (GND)
L - W-B
Battery power supply
Always
11 to 14 V
I12-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the I12 front power window regulator motor assembly LH connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the front power window regulator motor assembly LH may be malfunctioning.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I12-10 (UP) - I12-1 (GND)
L - W-B
Power window up operation
Ignition switch ON, multiplex network master switch off → up
11 to 14 V → Below 1 V
I12-10 (UP) - I12-1 (GND)
L - W-B
Power window up operation
Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
I12-7 (DOWN) - I12-1 (GND)
B - W-B
Power window down operation
Ignition switch ON, multiplex network master switch off → down
11 to 14 V → Below 1 V
I12-7 (DOWN) - I12-1 (GND)
B - W-B
Power window down operation
Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V
| CHECK FRONT POWER WINDOW REGULATOR MOTOR RH (for RHD) |
![]() ![]() |
Disconnect the I4 front power window regulator motor assembly RH connector.
Measure the resistance and voltage according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I4-2 (B) - I4-1 (GND)
L - W-B
Battery power supply
Always
11 to 14 V
I4-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the I4 front power window regulator motor assembly RH connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the front power window regulator motor assembly may be malfunctioning.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I4-10 (UP) - I4-1 (GND)
L - W-B
Power window up operation
Ignition switch ON, power window regulator switch off → up
11 to 14 V → Below 1 V
I4-10 (UP) - I4-1 (GND)
L - W-B
Power window up operation
Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
I4-7 (DOWN) - I4-1 (GND)
B - W-B
Power window down operation
Ignition switch ON, power window regulator switch off → down
11 to 14 V → Below 1 V
I4-7 (DOWN) - I4-1 (GND)
B - W-B
Power window down operation
Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V
| CHECK MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY |


- *1: for LHD
- *2: for RHD
Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
for LHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I31-6 (B) - I31-1 (E)
L - W-B
Battery power supply
Always
11 to 14 V
I31-1 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
If the result is not as specified, there may be a malfunction on the wire harness side.for RHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I26-6 (B) - I26-9 (E)
L - W-B
Battery power supply
Always
11 to 14 V
I26-9 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the I31*1 or I26*2 multiplex network master switch assembly connector.
Measure the voltage according to the value(s) in the table below.
for LHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I31-8 (U) - I31-1 (E)
L - W-B
Power window up operation
Ignition switch ON, multiplex network master switch off → up
11 to 14 V → Below 1 V
I31-8 (U) - I31-1 (E)
L - W-B
Power window up operation
Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
I31-5 (D) - I31-1 (E)
B - W-B
Power window down operation
Ignition switch ON, multiplex network master switch off → down
11 to 14 V → Below 1 V
I31-5 (D) - I31-1 (E)
B - W-B
Power window down operation
Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V
I31-4 (AUTO) - I31-1 (E)
G - W-B
Power window up operation
Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
I31-4 (AUTO) - I31-1 (E)
G - W-B
Power window down operation
Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V
I31-3 (LED+) - I31-1 (E)
R - W-B
LED illumination signal
Ignition switch ON
11 to 14 V
I31-3 (LED+) - I31-1 (E)
R - W-B
LED illumination signal
Approximately 45 second after ignition switch turned off
Below 1 V
If the result is not as specified, the multiplex network master switch assembly may be malfunctioning.for RHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I26-1 (U) - I26-9 (E)
L - W-B
Power window up operation
Ignition switch ON, multiplex network master switch off → up
11 to 14 V → Below 1 V
I26-1 (U) - I26-9 (E)
L - W-B
Power window up operation
Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
I26-5 (D) - I26-9 (E)
B - W-B
Power window down operation
Ignition switch ON, multiplex network master switch off → down
11 to 14 V → Below 1 V
I26-5 (D) - I26-9 (E)
B - W-B
Power window down operation
Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V
I26-4 (AUTO) - I26-9 (E)
G - W-B
Power window up operation
Ignition switch ON, door glass fully open → power window auto up operation → door glass fully closed
11 to 14 V → Below 1 V → 11 to 14 V
I26-4 (AUTO) - I26-9 (E)
G - W-B
Power window down operation
Ignition switch ON, door glass fully closed → power window auto down operation → door glass fully open
11 to 14 V → Below 1 V → 11 to 14 V
I26-3 (LED+) - I26-9 (E)
R - W-B
LED illumination signal
Ignition switch ON
11 to 14 V
I26-3 (LED+) - I26-9 (E)
R - W-B
LED illumination signal
Approximately 45 second after ignition switch turned off
Below 1 V
| CHECK FRONT POWER WINDOW REGULATOR SWITCH ASSEMBLY |


- *1: for LHD
- *2: for RHD
Disconnect the I28*1 or I30*2 front power window regulator switch assembly connector.
Measure the resistance according to the value(s) in the table below.
for LHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I28-3 (B) - Body ground
L - Body ground
Power supply
Ignition switch ON
11 to 14 V
I28-5 (SU) - Body ground
P - Body ground
Ground
Always
Below 1 Ω
I28-2 (SD) - Body ground
R-B - Body ground
Ground
Always
Below 1 Ω
If the result is not as specified, there may be a malfunction on the wire harness side.for RHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I30-3 (B) - Body ground
L - Body ground
Power supply
Ignition switch ON
11 to 14 V
I30-5 (SU) - Body ground
P - Body ground
Ground
Always
Below 1 Ω
I30-2 (SD) - Body ground
R-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the I28*1 or I30*2 front power window regulator switch assembly connector.
Measure the voltage according to the value(s) in the table below.
for LHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I28-4 (U) - Body ground
L - Body ground
Power window up operation
Ignition switch ON, power window regulator switch off → up
Below 1 V → 11 to 14 V
I28-1 (D) - Body ground
B - Body ground
Power window down operation
Ignition switch ON, power window regulator switch off → down
Below 1 V → 11 to 14 V
If the result is not as specified, the front power window regulator switch assembly may be malfunctioning.for RHD Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
I30-4 (U) - Body ground)
L - Body ground
Power window up operation
Ignition switch ON, power window regulator switch off → up
Below 1 V → 11 to 14 V
I30-1 (D) - Body ground
B - Body ground
Power window down operation
Ignition switch ON, power window regulator switch off → down
Below 1 V → 11 to 14 V
| CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |
![]() ![]() |
Disconnect the J23 rear power window regulator switch assembly LH connector.
Measure the resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
J23-3 (B) - Body ground
L - Body ground
Power supply
Ignition switch ON
11 to 14 V
J23-5 (SU) - Body ground
R - Body ground
Ground
Always
Below 1 Ω
J23-2 (SD) - Body ground
G - Body ground
Ground
Always
Below 1 Ω
Reconnect the J23 rear power window regulator switch assembly LH connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the rear power window regulator switch assembly LH may be malfunctioning.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
J23-4 (U) - Body ground
L - Body ground
Power window up operation
Ignition switch ON, power window regulator switch off → up
Below 1 V → 11 to 14 V
J23-1 (D) - Body ground
B - Body ground
Power window down operation
Ignition switch ON, power window regulator switch off → down
Below 1 V → 11 to 14 V
| CHECK REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
![]() ![]() |
Disconnect the J21 rear power window regulator switch assembly RH connector.
Measure the resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
J21-3 (B) - Body ground
L - Body ground
Power supply
Ignition switch ON
11 to 14 V
J21-5 (SU) - Body ground
B - Body ground
Ground
Always
Below 1 Ω
J21-2 (SD) - Body ground
W - Body ground
Ground
Always
Below 1 Ω
Reconnect the J21 rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the rear power window regulator switch assembly RH may be malfunctioning.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
J21-4 (U) - Body ground
L - Body ground
Power window up operation
Ignition switch ON, power window regulator switch off → up
Below 1 V → 11 to 14 V
J21-1 (D) - Body ground
B - Body ground
Power window down operation
Ignition switch ON, power window regulator switch off → down
Below 1 V → 11 to 14 V
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |


Disconnect the 2A, 2C, 2D, E1 and E2 ECU connectors.
Measure the resistance and voltage according to value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
2D-62 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
2A-1 (IG) - Body ground
B - Body ground
IG power supply
Always
11 to 14 V
E1-24 (DCTY) - Body ground
L - Body ground*1
Y - Body ground*2
Driver side door courtesy light switch input
Driver side door open
Below 1 Ω
Driver side door closed
10 kΩ or higher
E2-21 (PCTY) - Body ground
Y - Body ground*1
L - Body ground*2
Front passenger side door courtesy light switch input
Front passenger side door open
Below 1 Ω
Front passenger side door closed
10 kΩ or higher
E1-17 (RCTY) - Body ground
G - Body ground
Rear RH side door courtesy light switch input
Rear RH side door open
Below 1 Ω
Rear RH side door closed
10 kΩ or higher
2C-2 (LCTY) - Body ground
W - Body ground
Rear LH side door courtesy light switch input
Rear LH side door open
Below 1 Ω
Rear LH side door closed
10 kΩ or higher
- *1: for LHD
- *2: for RHD
- If the result is not as specified, the wire harness side may have a malfunction.
- *1: for LHD



