TERMINALS OF ECU
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| CHECK MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) |


Disconnect the E1, E2 and 2D main body ECU connectors.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E1-6 (AM1) - Body ground
W - Body ground
+B power supply
Always
11 to 14 V
E2-1 (AM2) - Body ground
W - Body ground
+B power supply
Always
11 to 14 V
E1-17 (SSW1) - Body ground
B - Body ground
Engine switch 1 input
Engine switch pushed
Below 1 Ω
E1-17 (SSW1) - Body ground
B - Body ground
Engine switch 1 input
Engine switch not pushed
10 kΩ or higher
E1-16 (SSW2) - Body ground
B - Body ground
Engine switch 2 input
Engine switch pushed
Below 1 Ω
E1-16 (SSW2) - Body ground
B - Body ground
Engine switch 2 input
Engine switch not pushed
10 kΩ or higher
2D-62 (GND2) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
2D-20 (LIN1) - Body ground
GR - Body ground
LIN line
Always
10 kΩ or higher
Reconnect the E1, E2 and 2D main body ECU connectors.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E1-22 (ACCD) - 2D-62 (GND2)
P - W-B
ACC relay drive signal
Engine switch on (ACC)
11 to 14 V
E1-22 (ACCD) - 2D-62 (GND2)
P - W-B
ACC relay drive signal
Engine switch off
Below 1 V
E1-3 (IG1D) - 2D-62 (GND2)
G - W-B
IG1 No. 3 relay drive signal
Engine switch on (IG)
11 to 14 V
E1-3 (IG1D) - 2D-62 (GND2)
G - W-B
IG1 No. 3 relay drive signal
Engine switch on (ACC)
Below 1 V
E2-11 (IG2D) - 2D-62 (GND2)
B - W-B
Integration relay (IG2 relay) drive signal
Engine switch on (IG)
11 to 14 V
E2-11 (IG2D) - 2D-62 (GND2)
B - W-B
Integration relay (IG2 relay) drive signal
Engine switch on (ACC)
Below 1 V
E1-19 (SLR+) - 2D-62 (GND2)
G - W-B
Steering lock power supply
Steering lock motor operating
Below 1 V
E1-19 (SLR+) - 2D-62 (GND2)
G - W-B
Steering lock power supply
Steering lock motor not operating
11 to 14 V
E1-8 (STR) - 2D-62 (GND2)
L - W-B
Park/neutral position switch signal*1
Clutch pedal switch signal*2
Engine switch on (IG), shift lever not in P or N → P or N*1
Engine switch on (IG), Clutch pedal switch released → Depressed*2
Below 2 V → Pulse generation*3
E1-18 (SLP) - 2D-62 (GND2)
SB - W-B
Steering lock actuator position signal
Steering lock locked
11 to 14 V
E1-18 (SLP) - 2D-62 (GND2)
SB - W-B
Steering lock actuator position signal
Steering lock released
Below 1 V
E3-9 (SPD) - 2D-62 (GND2)
V - W-B
Speed signal from combination meter
Engine switch on (IG), driving wheel rotating slowly
Pulse generation
(see waveform 1)
E3-8 (TACH) - 2D-62 (GND2)
W - W-B
Tachometer signal
Engine running
Pulse generation
(see waveform 2)
E4-2 (P) - 2D-62 (GND2)*1
L - W-B
Shift lock signal
Shift lever in P
Pulse generation
(see waveform 3)
E4-2 (P) - 2D-62 (GND2)*1
L - W-B
Shift lock signal
Shift lever not in P
Below 1 V
E4-4 (STSW) - 2D-62 (GND2)
R - W-B
Starter activation request signal
Brake pedal depressed, engine switch depressed*1
Clutch pedal depressed, engine switch depressed*2
11 to 14 V
E1-15 (INDS) - 2D-62 (GND2)
W - W-B
Vehicle condition signal
Brake pedal released with shift lever in P or N, engine switch off, on (ACC), or on (IG)*1
Clutch pedal released, engine switch off, on (ACC), or on (IG)*2
9 to 14 V
E1-14 (INDW) - 2D-62 (GND2)
W - W-B
Vehicle condition signal
Brake pedal released with shift lever in P or N, engine switch off, on (ACC), or on (IG)*1
Clutch pedal released, engine switch off, on (ACC), or on (IG)*2
9 to 14 V
E1-25 (SWIL) - 2D-62 (GND2)
R - W-B
Illumination signal
Light control switch tail or head
11 to 14 V
2B-22 (STP) - 2D-62 (GND2)
R - W-B
Stop light switch signal
Brake pedal depressed
11 to 14 V
2B-22 (STP) - 2D-62 (GND2)
R - W-B
Stop light switch signal
Brake pedal released
Below 1 V
- HINT:
- *1: for A/T
- *2: for M/T
- *3: Remove the ST CUT relay before measuring the voltage.
Using an oscilloscope, check the signal waveform of the ECU.
Waveform 1

Reference Terminal No. (Symbol)
Tool Setting
Condition
E3-9 (SPD) - 2D-62 (GND2)
5 V/DIV., 100 msec./DIV.
Driving at approx. 20 km/h (12 mph)
- HINT:
- As the vehicle speed increases, the wavelength shortens.
Waveform 2

Reference Terminal No. (Symbol)
Tool Setting
Condition
E3-8 (TACH) - 2D-62 (GND2)
10 V/DIV., 10 msec./DIV.
Engine switch on (IG) or engine started
Waveform 3

Reference Terminal No. (Symbol)
Tool Setting
Condition
E4-2 (P) - 2D-62 (GND2)
2 V/DIV., 20 msec./DIV.
Shift lever in P
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |


Disconnect the E29 certification ECU (smart key ECU assembly) connector.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E29-1 (+B) - Body ground
B - Body ground
+B power supply
Always
11 to 14 V
E29-10 (LIN) - Body ground
GR - Body ground
LIN line
Always
10 kΩ or higher
E29-17 (E) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
Reconnect the E29 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the certification ECU (smart key ECU assembly) may have a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E29-18 (IG) - Body ground
B - Body ground
Ignition power supply
Engine switch on (IG)
11 to 14 V
E29-18 (IG) - Body ground
B - Body ground
Ignition power supply
Engine switch off
Below 1 V
| CHECK ECM |
for LHD:
Disconnect the A38 and C45 ECM connectors.

Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A38-1 (BATT) - C45-81 (E1)*1, *2, *3
A38-20 (BATT) - C45-81 (E1)*4, *5
L - BR*1, *2, *4, *5
L - W-B*3
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
A38-3 (+B) - C45-81 (E1)*1, *2, *3
A38-2 (+B) - C45-81 (E1)*4, *5
B - BR*1, *2, *4, *5
B - W-B*3
Power source of ECM
Engine switch on (IG)
11 to 14 V
A38-28 (IGSW) - C45-81 (E1)
B - BR*1, *2, *4, *5
B - W-B*3
Engine switch signal
Always
11 to 14 V
C45-81 (E1) - Body ground
BR - Body ground*1, *2, *4, *5
W-B - Body ground*3
Ground
Always
Below 1 Ω
C45-43 (E01) - Body ground*1, *2, *3
C45-22 (E01) - Body ground*4, *5
W-B - Body ground
Ground
Always
Below 1 Ω
C45-42 (E02) - Body ground*1, *2, *3
C45-21 (E02) - Body ground*4, *5
BR - Body ground
Ground
Always
Below 1 Ω
C45-46 (E03) - Body ground*1, *2, *3
W-B - Body ground
Ground
Always
Below 1 Ω
C45-23 (E04) - Body ground*1, *2, *3
C45-44 (E04) - Body ground*5
W-B - Body ground*1, *2, *3
BR - Body ground*5
Ground
Always
Below 1 Ω
C45-21 (E05) - Body ground*1, *2, *3
C45-23 (E05) - Body ground*5
W-B - Body ground
Ground
Always
Below 1 Ω
- HINT:
- *1: for 1UR-FE
- *2: for 1GR-FE
- *3: for 3UR-FE
- *4: for 1VD-FTV w/o DPF
- *5: for 1VD-FTV w/DPF
Reconnect the ECM connectors.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A38-46 (STA) - C45-81 (E1)*1, *2, *3
A38-48 (STA) - C45-81 (E1)*4, *5
R-B - BR*1, *2, *4, *5
R-B - W-B*3
ST relay operation signal
Cranking
5.5 V or more
A38-14 (STSW) - C45-81 (E1)*1, *2, *3, *4
A38-47 (STSW) - C45-81 (E1)*5
R - BR*1, *2, *4, *5
R - W-B*3
Starter activation request signal
Brake pedal depressed, engine switch on (IG)
Output voltage at terminal AM1 or AM2 is -2 V or more
A38-41 (ACCR) - C45-81 (E1)*1, *2, *3
A38-13 (ACCR) - C45-81 (E1)*4
A38-22 (ACCR) - C45-81 (E1)*5
L-Y - BR*1, *2, *4, *5
L-Y - W-B*3
ACC relay cut signal
(output)
Engine switch on (IG) → Cranking
11 to 14 V → Below 1 V
A38-15 (TACH) - C45-81 (E1)
W-G - BR*1, *2, *4, *5
W-G - W-B*3
Engine speed signal
(output)
Idling
Pulse generation
(see waveform 1)
C45-16 (STAR) - C45-81 (E1)*1, *2, *3
C45-51 (STAR) - C45-81 (E1)*4
C45-52 (STAR) - C45-81 (E1)*5
L - BR*1, *2, *4, *5
L - W-B*3
ST relay drive signal
Cranking
11 to 14 V
- HINT:
- *1: for 1UR-FE
- *2: for 1GR-FE
- *3: for 3UR-FE
- *4: for 1VD-FTV w/o DPF
- *5: for 1VD-FTV w/ DPF
Using an oscilloscope, check the signal waveform of the ECM.

Reference Terminal No. (Symbol)
Tool Setting
Condition
A38-15 (TACH) - C45-81 (E1)
5 V/DIV., 10 ms./DIV.
Engine idling
- HINT:
- As the engine speed increases, the wavelength shortens.
for RHD:
Disconnect the A52 and C46 ECM connectors.

Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A52-1 (BATT) - C46-81 (E1)*1. *2
A52-20 (BATT) - C46-81 (E1)*3, *4
L - BR
Battery (for measuring battery voltage and for ECM memory)
Always
11 to 14 V
A52-3 (+B) - C46-81 (E1)*1, *2
A52-2 (+B) - C46-81 (E1)*3, *4
B - BR
Power source of ECM
Engine switch on (IG)
11 to 14 V
A52-28 (IGSW) - C46-81 (E1)
B - BR
Engine switch signal
Always
11 to 14 V
C46-81 (E1) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
C46-43 (E01) - Body ground*1, *2
C46-22 (E01) - Body ground*3, *4
W-B - Body ground
Ground
Always
Below 1 Ω
C46-42 (E02) - Body ground*1, *2
C46-21 (E02) - Body ground*3, *4
BR - Body ground
Ground
Always
Below 1 Ω
C46-46 (E03) - Body ground*1, *2
W-B - Body ground
Ground
Always
Below 1 Ω
C46-23 (E04) - Body ground*1, *2
C46-44 (E04) - Body ground*4
W-B - Body ground*1, *2
BR - Body ground*4
Ground
Always
Below 1 Ω
C46-21 (E05) - Body ground*1, *2
C46-23 (E05) - Body ground*4
W-B - Body ground
Ground
Always
Below 1 Ω
- HINT:
- *1: for 1UR-FE
- *2: for 1GR-FE
- *3: for 1VD-FTV w/o DPF
- *4: for 1VD-FTV w/ DPF
Reconnect the ECM connectors.
Measure the voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
A52-46 (STA) - C46-81 (E1)*1, *2
A52-48 (STA) - C46-81 (E1)*3, *4
R-B - BR
ST relay operation signal
Cranking
5.5 V or more
A52-14 (STSW) - C46-81 (E1)*1, *2, *3
A52-47 (STSW) - C46-81 (E1)*4
R - BR
Starter activation request signal
Brake pedal depressed, engine switch on (IG)
Output voltage at terminal AM1 or AM2 is -2 V or more
A52-41 (ACCR) - C46-81 (E1)*1, *2
A52-13 (ACCR) - C46-81 (E1)*3
A52-22 (ACCR) - C46-81 (E1)*4
L-Y - BR
ACC relay cut signal
(output)
Engine switch on (IG) → Cranking
11 to 14 V → Below 1 V
A52-15 (TACH) - C46-81 (E1)
W-G - BR
Engine speed signal
(output)
Idling
Pulse generation
(see waveform 1)
C46-16 (STAR) - C46-81 (E1)*1, *2
C46-51 (STAR) - C46-81 (E1)*3
C46-52 (STAR) - C46-81 (E1)*4
L - BR
ST relay drive signal
Cranking
11 to 14 V
- HINT:
- *1: for 1UR-FE
- *2: for 1GR-FE
- *3: for 1VD-FTV w/o DPF
- *4: for 1VD-FTV w/ DPF
Using an oscilloscope, check the signal waveform of the ECM.

Reference Terminal No. (Symbol)
Tool Setting
Condition
A52-15 (TACH) - C46-81 (E1)
5 V/DIV., 10 ms./DIV.
Engine idling
- HINT:
- As the engine speed increases, the wavelength shortens.
| CHECK STEERING LOCK ECU |


Disconnect the E26 steering lock ECU connector.
Measure the voltage and resistance according to the value(s) in the table below.
If the result is not as specified, there may be a malfunction on the wire harness side.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E26-7 (B) - Body ground
R - Body ground
+B power supply
Always
11 to 14 V
E26-6 (IG2) - Body ground
B - Body ground
Ignition power supply
Engine switch on (IG)
11 to 14 V
E26-6 (IG2) - Body ground
B - Body ground
Ignition power supply
Engine switch off
Below 1 V
E26-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
E26-2 (SGND) - Body ground
BR - Body ground
Ground
Always
Below 1 Ω
Reconnect the E26 steering lock ECU connector.
Measure the voltage according to the value(s) in the table below.
If the result is not as specified, the ECU may have a malfunction.Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E26-4 (SLP1) - E26-1 (GND)
SB - W-B
Steering lock actuator position signal
Steering locked
11 to 14 V
E26-4 (SLP1) - E26-1 (GND)
SB - W-B
Steering lock actuator position signal
Steering released
Below 1 V