2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012


1. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover sub-assembly.


4. REMOVE V-BANK COVER SUB-ASSEMBLY

  1. A274415E01
    Raise the front of the V-bank cover to detach the 3 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Grommet
    *2
    Pin
    *3
    Hook
    *4
    Bracket


5. DRAIN ENGINE COOLANT

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Loosen the radiator drain cock plug.

  1. Remove the radiator cap and drain the coolant.

    HINT:
    Collect the coolant in a container and dispose of it according to the regulations in your area.

  1. Loosen the 2 cylinder block drain cock plugs and drain the coolant from the engine.

  1. Tighten the 2 cylinder block drain cock plugs.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Tighten the radiator drain cock plug by hand.

    A266163E01

    Text in Illustration 
    *1
    Reservoir Cap
    *2
    Radiator Cap
    *3
    Radiator Drain Cock Plug
    *4
    Cylinder Block Drain Cock Plug


6. REMOVE AIR CLEANER CAP AND HOSE

  1. A272589
    Disconnect the No. 2 PCV hose and No. 1 air hose.

  1. Disconnect the mass air flow meter connector and detach the clamp.

  1. Detach the 4 clamps.

  1. Loosen the hose clamp and remove the air cleaner cap and hose.


7. REMOVE NO. 1 RADIATOR HOSE

  1. A178878
    Remove the No. 1 radiator hose.


8. REMOVE FAN SHROUD
  1. Loosen the 4 nuts holding the fluid coupling fan.

  1. Remove the fan and generator V-belt (Click here).

  1. A238869
    Disconnect the reservoir hose from the upper radiator tank.

  1. w/ Air Cooled Transmission Oil Cooler:
    Detach the claw to open the flexible hose clamp.

  1. Remove the 2 bolts and disconnect the oil cooler tube from the fan shroud.

  1. Remove the 2 bolts holding the fan shroud.

  1. Remove the 4 nuts of the fluid coupling fan, and then remove the shroud together with the fluid coupling fan.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Remove the fan pulley from the engine water pump.


9. DISCONNECT NO. 2 RADIATOR HOSE

  1. A218802
    Disconnect the No. 2 radiator hose.


10. REMOVE WATER INLET SUB-ASSEMBLY WITH THERMOSTAT

  1. A218803
    Remove the 3 nuts, the water inlet with thermostat, and the gasket.

← COMPONENTS (from Jan 2012)INSPECTION (from Jan 2012) →