2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSPECT CONNECTING ROD THRUST CLEARANCE

  1. A075147E01
    Using a dial indicator, measure the thrust clearance while moving the connecting rod back and forth.

    Standard thrust clearance:
    0.15 to 0.30 mm (0.00591 to 0.0118 in.)

    Maximum thrust clearance:
    0.35 mm (0.0138 in.)

    If the thrust clearance is more than the maximum, replace one or more connecting rods as necessary.
    If necessary, replace the crankshaft.


2. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD

  1. A076043E01
    Using a ridge reamer, remove all the carbon from the top of the cylinder.

  1. Uniformly loosen the connecting rod bolts, and remove the connecting rod cap with bearing.

  1. Push out the piston with connecting rod and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearings, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.


3. REMOVE CONNECTING ROD BEARING

4. REMOVE PISTON RING SET

  1. A076044E01
    Using a piston ring expander, remove the 2 compression rings.

  1. Remove the 2 side rails and oil ring (expander) by hand.


5. REMOVE PISTON PIN HOLE SNAP RING

  1. P012403E01
    Using a screwdriver, pry out the 2 snap rings.


6. REMOVE PISTON WITH PIN SUB-ASSEMBLY

  1. A076045E08
    Gradually heat the piston to approximately 80°C (176°F).

  1. A076046E01
    Using a plastic-faced hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.


7. INSPECT CRANKSHAFT THRUST CLEARANCE

  1. A076047E01
    Using a dial indicator, measure the thrust clearance while prying the crankshaft back and forth with a screwdriver.

    Standard thrust clearance:
    0.04 to 0.24 mm (0.00157 to 0.00945 in.)

    Maximum thrust clearance:
    0.30 mm (0.0118 in.)

    If the thrust clearance is more than the maximum, replace the thrust washers as a set.

    Standard thrust washer thickness:
    1.93 to 1.98 mm (0.0760 to 0.0780 in.)

    If necessary, replace the crankshaft.


8. REMOVE CRANKSHAFT

  1. A076048E03
    Using several steps, loosen and remove the 8 bearing cap bolts and seal washers uniformly in the sequence shown in the illustration.

  1. A076049E03
    Using several steps, loosen and remove the 16 bearing cap bolts uniformly in the sequence shown in the illustration.

  1. A076050E01
    Using a screwdriver, pry out the bearing caps. Remove the 4 bearing caps and lower bearings.

    NOTICE:
    1. Push up on the cap little by little, alternating from the right and left side until the cap can be removed.
    2. Be careful not to damage the joint surfaces of the cylinder block and bearing cap.


9. REMOVE CRANKSHAFT BEARING

10. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY

  1. A076051E01
    Using a 5 mm hexagon socket wrench, remove the 3 bolts and 3 oil nozzles.

← COMPONENTS (from Jan 2012)DISASSEMBLY (from Jan 2012) →