2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ON-VEHICLE INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011


INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the intelligent tester.

    2. Start the engine and idle it.

    3. Push the intelligent tester main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

      Standard ignition timing:
      5 to 15° BTDC @ idling (transmission in neutral and A/C switch off)

    5. Disconnect the intelligent tester from the DLC3.

  1. A180851
    When not using the intelligent tester:

    1. Remove the 2 nuts and V-bank cover.

    2. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.

    3. H102392E79
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. Switch off all accessories and the A/C.

    4. A004459E01
      Using the timing light, check the ignition timing.

      Ignition timing:
      5 to 15° BTDC @ idling (transmission in neutral and A/C switch off)

    5. Remove SST from the DLC3.

    6. Disconnect the timing light from the engine.

    7. Install the V-bank cover with the 2 nuts.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the intelligent tester.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Push the intelligent tester main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      HINT:
      Refer to the intelligent tester operator's manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the intelligent tester from the DLC3.

  1. H102392E88
    When not using the intelligent tester:

    1. Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting the probe. Connecting the probe to the wrong terminal can damage the engine.
      2. Switch off all accessories and the A/C.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Check the idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      If the idle speed is not as specified, check the air intake system.

    4. Disconnect the tachometer from the DLC3.


INSPECT COMPRESSION
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. Check for DTCs (Click here).

  1. Remove the 2 nuts and V-bank cover.

  1. Remove the air cleaner hose assembly.

  1. Disconnect the 8 injector connectors and 8 ignition coil connectors.

  1. Remove the 8 bolts and 8 ignition coils.

  1. Remove the 8 spark plugs.

  1. A074993E01
    Check the cylinder compression pressure.

    NOTICE:
    Check the compression pressure of each cylinder in the same way.


    1. Insert a compression gauge into the spark plug hole.

    2. Fully open the throttle.

    3. While cranking the engine, measure the compression pressure.

      Standard compression pressure:
      1373 kPa (14.0 kgf/cm2, 199 psi) or more

      Minimum pressure:
      1030 kPa (10.5 kgf/cm2, 149 psi)

      Difference between each cylinder:
      98 kPa (1.0 kgf/cm2, 14.2 psi) or less

      NOTICE:
      1. Always use a fully charged battery to obtain an engine speed of 250 rpm or more.
      2. This measurement must be done as quickly as possible.

    4. If the cylinder compression is low in one or more cylinders, pour a small amount of engine oil into the cylinder with low compression through its spark plug hole. Then inspect the cylinder compression pressure again.

      HINT:
      1. If adding oil helps boost the compression, it is likely that the piston rings and/or cylinder bore are worn or damaged.
      2. If pressure stays low, a valve may be stuck or seated improperly, or there may be leakage in the gasket.

  1. Install the 8 spark plugs.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }

  1. Install the 8 ignition coils with the 8 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Connect the 8 injector connectors and 8 ignition coil connectors.

  1. Install the air cleaner hose assembly.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Clear the DTCs (Click here).


INSPECT CO/HC

HINT:
This check is used only to determine whether or not the idle CO/HC complies with regulations.

  1. Warm up the engine.

  1. Keep the engine speed at 2500 rpm for approximately 180 seconds.

  1. A174360E01
    Insert the CO/HC meter testing probe at least 40 cm (1.31 ft.) into the tailpipe during idling.

  1. Immediately check CO/HC concentration at idle and/or 2500 rpm.

    HINT:
    When performing the 2 mode (2500 rpm and idle) test, follow the measurement order prescribed by the applicable local regulations.

  1. If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.

    1. Check the A/F sensor (Click here) and heated oxygen sensor (Click here) operation.

    2. See the table below for possible causes, and then inspect and correct the applicable causes if necessary.

      CO
      HC
      Symptom
      Cause
      Normal
      High
      Rough idle
      1. Faulty ignitions:
        1. Incorrect timing
        2. Plugs (contaminated, shorted or gaps are defective)
      2. Incorrect valve clearance
      3. Leaky intake and exhaust valves
      4. Leaky cylinder
      Low
      High
      Rough idle
      (Fluctuating HC reading)
      1. Vacuum leaks:
        1. PCV hose
        2. Intake manifold
        3. Throttle body
      2. Lean mixture causing misfire
      High
      High
      Rough idle
      (Black smoke from exhaust)
      1. Restricted air filter
      2. Faulty SFI system:
        1. Faulty pressure regulator
        2. Defective ECT sensor
        3. Faulty ECM
        4. Faulty injectors
        5. Faulty throttle position sensor
        6. Faulty MAF meter

← REASSEMBLY (from Sep 2011)COMPONENTS (Sep 2011 – Dec 2011) →