2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011


1. INSTALL NO. 2 TIMING BELT IDLER SUB-ASSEMBLY

  1. A072699E01
    Install the timing belt idler with the bolt.

    Torque:
    35 N*m{ 352 kgf*cm , 25 ft.*lbf }


2. INSTALL NO. 1 TIMING BELT IDLER SUB-ASSEMBLY

  1. A072698E01
    When reusing the timing belt idler shaft, apply adhesive to 2 or 3 of the threads.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Using a 10 mm hexagon wrench, install the plate washer and timing belt idler with the idler shaft.

    Torque:
    35 N*m{ 352 kgf*cm , 25 ft.*lbf }


3. INSTALL TIMING BELT

  1. A176497E01
    Set the No. 1 cylinder to TDC/compression.

    1. Turn the hexagonal portion of the camshaft to align the timing marks of the camshaft timing pulleys and timing belt plates.

    2. A160751E02
      Using the pulley bolt, turn the crankshaft to align the timing marks of the crankshaft timing pulley and oil pump body.

  1. A160752
    Install the timing belt.

    1. Remove any oil or water from each pulley, and keep them clean.

      NOTICE:
      Only wipe the pulleys. Do not use any cleansing agent on the pulleys.

    2. Face the front mark (arrow) on the timing belt forward.

    3. Align the timing marks on the timing belt and crankshaft timing pulley, and the timing belt and camshaft timing pulleys, and install the timing belt.

  1. A054983E04
    Install the belt tensioner.

    1. Remove the dust seal from the belt tensioner.

    2. Using a press, slowly press in the push rod using a force of 981 to 9807 N (100 to 1000 kgf, 220.5 to 2204.7 lbf).

    3. Align the holes of the push rod and housing, and pass a 1.5 mm hexagon wrench through the holes to keep the setting position of the push rod.

    4. Release the press.

    5. Install the dust seal to the belt tensioner.

    6. A160753E02
      Temporarily install the belt tensioner with the 2 bolts.

    7. Tighten the 2 bolts.

      Torque:
      26 N*m{ 265 kgf*cm , 19 ft.*lbf }

    8. Using pliers, remove the 1.5 mm hexagon wrench from the timing belt tensioner.


4. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

  1. A176500E01
    Using the pulley bolt, slowly turn the crankshaft timing pulley 2 revolutions from the TDC to TDC.

    NOTICE:
    Always turn the crankshaft timing pulley clockwise.

  1. Check that each pulley is aligned with each timing mark as shown in the illustration.
    If the timing marks are not aligned, remove the timing belt and reinstall it.

  1. Remove the pulley bolt.


5. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE

  1. A176501E01
    Install the sensor plate as shown in the illustration.

    NOTICE:
    Take care not to install the sensor plate in a wrong direction.


6. INSTALL TIMING BELT COVER SPACER

  1. A175253
    Install the cover spacer and gasket.


7. INSTALL NO. 1 TIMING BELT COVER

  1. A175252
    Install the timing belt cover with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


8. INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY
  1. Align the pulley set key with the key groove of the crankshaft damper.

  1. A176502E01
    Using SST, hold the crankshaft pulley and install the pulley bolt.
    SST
    09213-70011   (09213-70020)
    09330-00021   (09330-00030)

    Torque:
    245 N*m{ 2498 kgf*cm , 181 ft.*lbf }


9. INSTALL FAN BRACKET SUB-ASSEMBLY

  1. A175251E01
    Install the fan bracket with the 2 bolts and 2 nuts.

    Torque:
    for nut A, bolt B:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }
    for nut C, bolt D:
    32 N*m{ 326 kgf*cm , 24 ft.*lbf }


10. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

  1. A175250
    Install the belt tensioner with the bolt and 2 nuts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


11. INSTALL NO. 2 TIMING BELT COVER SUB-ASSEMBLY

  1. A175249
    Install the timing belt cover and fit the 2 claws into each part.

  1. Install the 2 bolts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


12. INSTALL NO. 3 TIMING BELT COVER SUB-ASSEMBLY RH

  1. A175248
    Install the timing belt cover with the 3 bolts and nut.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


13. INSTALL NO. 3 TIMING BELT COVER SUB-ASSEMBLY LH

  1. A175247
    Pass the camshaft position sensor wire through the cover hole.

  1. Install the timing belt cover with the 4 bolts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }

  1. Install the wire grommet to the timing belt cover.

  1. Connect the sensor connector.

  1. Install the sensor wire to the 2 wire clamps on the cover.

  1. A178915
    Connect the engine wire to the 3 wire clamps.

  1. Connect the camshaft timing oil control valve connector and control motor connector.


14. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

  1. A110456
    Install the idler pulley and cover plate with the bolt.

    Torque:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }


15. INSTALL OIL COOLER PIPE

  1. A108784E04
    Using needle-nose pliers, grip the claws of the clamps and slide the clamps to connect the 3 water by-pass hoses.

  1. Install the oil cooler pipe with the cap nut and bolt.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


16. INSTALL GENERATOR ASSEMBLY

  1. A177924E01
    Install the generator with the bolt and 2 nuts.

    Torque:
    for bolt and nut (A):
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    for nut (B):
    16 N*m{ 158 kgf*cm , 11 ft.*lbf }

  1. A177923
    Connect the generator connector.

  1. Connect the generator wire with the nut.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the terminal cap.

  1. Connect the harness bracket to the generator with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


17. CONNECT VANE PUMP ASSEMBLY

  1. C179184
    Connect the vane pump with the 2 bolts and nut.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. C158740
    Connect the connector.


18. CONNECT COOLER COMPRESSOR ASSEMBLY

  1. A180811E01
    Connect the compressor. Then install it and the No. 1 compressor stay with the nut and 3 bolts.

    Torque:
    for bolt:
    45 N*m{ 459 kgf*cm , 33 ft.*lbf }
    for nut:
    25 N*m{ 250 kgf*cm , 18 ft.*lbf }

    HINT:
    Tighten the bolts in the order shown in the illustration to install the cooler compressor.

  1. Install the cooler refrigerant suction hose with the bolt.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Connect the connector.


19. INSTALL NO. 2 RADIATOR HOSE

  1. A180841E01
    Using needle-nose pliers, grip the claws of the clamps and slide the clamps to install the radiator hose.


20. INSTALL FAN SHROUD

  1. A162053
    Install the fan pulley to the water pump.

  1. Place the shroud together with the cooling fan between the radiator and engine.

    NOTICE:
    Be careful not to damage the radiator core.

  1. Temporarily install the cooling fan to the water pump with the 4 nuts. Tighten the nuts as much as possible by hand.

  1. A180842E01
    Attach the claws of the shroud to the radiator as shown in the illustration.

  1. Install the shroud with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the oil cooler tube to the fan shroud with the 2 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. w/ Air Cooled Transmission Oil Cooler:
    Pass the hose through the flexible hose clamp and close the clamp as shown in the illustration.

  1. Connect the reservoir hose to the upper side of the radiator tank.

  1. A162053
    Tighten the 4 nuts of the cooling fan.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


21. INSTALL FAN & GENERATOR V BELT

  1. A178870E01
    Set the V belt onto every part except the belt tensioner, as shown in the illustration.

  1. Loosen the V belt by turning the belt tensioner counterclockwise.

  1. Set the V belt to the belt tensioner.

  1. A141644E02
    Check that the belt fits properly in the ribbed grooves.

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.

  1. A178869E01
    Check that the arrow on the belt tensioner is within area "A".
    If the arrow is outside area "A", replace the fan and generator V belt.

    HINT:
    When a new belt is installed, the arrow should be within area "B". If not, the fan and generator V belt is not installed correctly.


22. INSTALL NO. 1 RADIATOR HOSE

  1. A178884E01
    Using needle-nose pliers, grip the claws of the clamps and slide the clamps to install the radiator hose.


23. INSTALL AIR CLEANER HOSE ASSEMBLY

  1. A175168E01
    Install the air cleaner hose so that the protrusion of the air cleaner cap aligns with the groove of the hose as shown in the illustration.

  1. Tighten the 2 clamps.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum transmitting hose.

  1. Connect the No. 2 ventilation hose.


24. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


25. ADD ENGINE COOLANT
  1. Add engine coolant.

    Standard Capacity:
    Item
    Specified Condition
    w/o Transmission oil cooler
    w/o Rear Heater
    13.4 liters (14.2 US qts, 11.8 Imp. qts)
    w/ Rear Heater
    16.3 liters (17.2 US qts, 14.3 Imp. qts)
    w/ Transmission oil cooler
    w/o Rear Heater
    14.1 liters (14.9 US qts, 12.4 Imp. qts)
    w/ Rear Heater
    16.9 liters (17.9 US qts, 14.9 Imp. qts)

    HINT:
    TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology consists of a combination of low phosphates and organic acids).

  1. A168577
    Slowly pour coolant into the radiator reservoir until it reaches the F line.

  1. Install the radiator reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    NOTICE:
    Switch off the A/C.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the F line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the cooling fan.

  1. Stop the engine, and wait until the engine coolant cools down to the ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. A168578
    Check that the coolant level is between the F and L lines. If the coolant level is below the L line, repeat all of the procedures above. If the coolant level is above the F line, drain coolant so that the coolant level is between the F and L lines.


26. INSPECT FOR COOLANT LEAK

  1. A168576
    Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 123 kPa (1.3 kgf/cm2, 18 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.


27. INSPECT IGNITION TIMING
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the intelligent tester.

    2. Start the engine and idle it.

    3. Push the intelligent tester main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / IGN Advance.

      HINT:
      Refer to the intelligent tester operator's manual for further details.

      Standard ignition timing:
      5 to 15° BTDC @ idling (transmission in neutral and A/C switch off)

    5. Disconnect the intelligent tester from the DLC3.

  1. A180851
    When not using the intelligent tester:

    1. Remove the 2 nuts and V-bank cover.

    2. Connect the tester probe of a timing light to the wire of the ignition coil connector for the No. 1 cylinder.

      NOTICE:
      Use a timing light that detects primary signals.

    3. H102392E79
      Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
      SST
      09843-18040  

      NOTICE:
      1. Confirm the terminal numbers before connecting them. Connecting the wrong terminals can damage the engine.
      2. Switch off all accessories and the A/C.

    4. A004459E01
      Using the timing light, check the ignition timing.

      Ignition timing:
      5 to 15° BTDC @ idling (transmission in neutral and A/C switch off)

    5. Remove SST from the DLC3.

    6. Disconnect the timing light from the engine.

    7. Install the V-bank cover with the 2 nuts.

      Torque:
      7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


28. INSPECT ENGINE IDLE SPEED
  1. Warm up and stop the engine.

    1. Allow the engine to warm up to a normal operating temperature.

  1. When using the intelligent tester:

    1. Connect the intelligent tester to the DLC3.

      NOTICE:
      Switch off all accessories and the A/C before connecting the intelligent tester.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Push the intelligent tester main switch ON.

    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Primary / Engine Speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      HINT:
      Refer to the intelligent tester operator's manual for further details.

      If the idle speed is not as specified, check the air intake system.

    5. Disconnect the intelligent tester from the DLC3.

  1. H102392E88
    When not using the intelligent tester:

    1. Using SST, connect a tachometer probe to terminal 9 (TAC) of the DLC3.

      SST
      09843-18030  

      NOTICE:
      1. Confirm the terminal number before connecting the probe. Connecting the probe to the wrong terminal can damage the engine.
      2. Switch off all accessories and the A/C.

    2. Race the engine at 2500 rpm for approximately 90 seconds.

    3. Check the idle speed.

      Standard idle speed:
      650 to 750 rpm (transmission in neutral and A/C switch off)

      If the idle speed is not as specified, check the air intake system.

    4. Disconnect the tachometer from the DLC3.


29. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A178997
    Attach the 2 V-bank cover hooks to the bracket.

  1. Install the V-bank cover with the 2 nuts.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }


30. INSTALL FRONT FENDER APRON SEAL LH

  1. A176301
    Install the fender apron seal with the 4 clips.


31. INSTALL FRONT FENDER APRON SEAL LH (w/ KDSS)

  1. A177004
    Install the fender apron seal with the 3 clips.


32. INSTALL FRONT FENDER APRON SEAL FRONT RH

  1. A177003
    Install the fender apron seal with the 3 clips.


33. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Install the No. 1 engine under cover with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


34. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


35. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


36. INSPECT ENGINE COOLANT LEVEL

A178872
  1. Check that the engine coolant level is between the L and F lines when the engine is cold.
    If the engine coolant is low, check for leaks and add "TOYOTA Super Long Life Coolant" or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite and non-borate coolant with long-life hybrid organic acid technology to the F line.

    NOTICE:
    Do not substitute plain water for engine coolant.

  1. Remove the radiator cap, and check that the coolant level is up to the radiator filler hole.

← INSPECTION (Sep 2011 – Dec 2011)COMPONENTS (Sep 2011 – Dec 2011) →