2011-2013 Land Cruiser · Service Manual Power Source / Network

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL GENERATOR ASSEMBLY
  1. Install the stud bolt.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }

  1. Install the generator with the 3 bolts and nut.

    Torque:
    43 N*m{ 438 kgf*cm , 32 ft.*lbf }

  1. Connect the generator connector.

  1. Connect the generator wire with the nut.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }

  1. Install the terminal cap.

  1. Install the harness bracket to the generator with the bolt.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }


2. CONNECT OIL COOLER PIPE ASSEMBLY
  1. Connect the oil cooler pipe with the 2 bolts.

    Torque:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }


3. CONNECT VANE PUMP ASSEMBLY

A163333E04

HINT:
Before performing the following procedures, move the spacer until the vane pump can be installed.
Text in Illustration 
*1
Spacer

  1. Connect the vane pump to the timing chain cover with the 2 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }


4. INSTALL AIR CLEANER ASSEMBLY
  1. Install the air cleaner with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


5. INSTALL AIR CLEANER HOSE ASSEMBLY

  1. A243381E01
    Install the air cleaner hose so that the protrusion of the air cleaner cap aligns with the groove of the hose as shown in the illustration.
    Text in Illustration 
    *1
    Groove
    *2
    Protrusion

  1. Tighten the 2 clamps.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Connect the vacuum hose.

  1. Connect the No. 2 ventilation hose.


6. INSTALL FRONT FENDER APRON SEAL FRONT RH
  1. Install the fender apron seal with the 3 clips.


7. INSTALL FAN AND GENERATOR V BELT

  1. A163771E05
    Set the V belt onto every part.

  1. While turning the belt tensioner counterclockwise, remove the bar.

    Text in Illustration 
    *1
    Vane Pump
    *2
    Water Pump
    *3
    No. 1 Idler
    *4
    Fan
    *5
    Generator
    *6
    Belt Tensioner
    *7
    Crankshaft
    *8
    Cooler Compressor

    NOTICE:
    Make sure that the V belt is properly set to each pulley.

  1. B000540E14
    After installing the belt, check that it fits properly in the ribbed grooves.
    Text in Illustration 
    *a
    CORRECT
    *b
    INCORRECT

    HINT:
    Make sure to check by hand that the belt has not slipped out of the grooves on the bottom of the pulley.


8. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
  1. Install the No. 1 engine under cover with the 10 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


9. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

B180991
  1. Push in the clip indicated by the arrow in the illustration to install the fender splash shield.

  1. Install the 3 bolts and screw.


10. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.


11. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable from the cable is reconnected (Click here).


12. INSTALL V-BANK COVER SUB-ASSEMBLY

  1. A177597E02
    Attach the 2 V-bank cover hooks to the bracket. Then align the 3 V-bank cover grommets with the 3 pins, and press down on the V-bank cover to attach the pins.
    Text in Illustration 
    *1
    Bracket
    *2
    Hook
    *3
    Pin
    *4
    Grommet

← REASSEMBLY (from Jan 2012)INSTALLATION (from Jan 2012) →