2011-2013 Land Cruiser · Service Manual Drivetrain

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

HINT:
Coat all of the sliding and rotating surfaces with gear oil before reassembly.


1. INSTALL REAR TRANSFER OUTPUT SHAFT

  1. C173615
    Install a new needle roller bearing.

  1. C173617E01
    Using SST and a press, press in a new bearing.
    SST
    09527-10011  

    NOTICE:
    Set the snap ring groove of the bearing to the front side.


2. INSTALL TRANSFER DRIVE SPROCKET BEARING

  1. C173614
    Install the bearing to the output shaft.


3. INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

  1. C173613
    Install the drive sprocket to the output shaft.


4. INSTALL TRANSFER OUTPUT SHAFT SPACER

  1. C173612E01
    Install the straight pin to the output shaft.

  1. C173621
    Align the straight pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.

  1. C173625
    Using a screwdriver and hammer, tap on the snap ring.


5. INSPECT TRANSFER DRIVE SPROCKET SUB-ASSEMBLY

  1. C173640
    Using a feeler gauge, measure the drive sprocket thrust clearance.

    Standard Clearance:
    0.10 to 0.47 mm (0.00394 to 0.0185 in.)

    Maximum Clearance:
    0.47 mm (0.0185 in.)

    If the clearance is more than the maximum, replace the drive sprocket sub-assembly.


6. INSTALL CENTER DIFFERENTIAL CASE

  1. C173618E01
    Using SST and a hammer, tap in a new needle roller bearing until its surface is 0 to 0.5 mm (0 to 0.0197 in.) from the center differential case upper surface.
    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07100)

    NOTICE:
    1. Be careful not to damage the center differential case.
    2. Install the bearing so that the mark is on the outside.

  1. C173619E01
    Using SST and a hammer, tap in a new needle roller bearing until its surface is 1.5 to 2.0 mm (0.0591 to 0.0787 in.) from the center differential case upper surface.
    SST
    09950-60010   (09951-00460)
    09950-70010   (09951-07100)

    NOTICE:
    1. Be careful not to damage the center differential case.
    2. Install the bearing so that the mark is on the outside.

  1. C173620E01
    for Manual Transmission:
    Install the synchromesh shifting key spring and No. 2 synchromesh shifting keys as shown in the illustration.

  1. C173607
    for Manual Transmission:
    Using a snap ring expander, install the snap ring.

  1. C173606
    Install the center differential case to the output shaft.


7. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER

  1. C173605E01
    Install the straight pin to the output shaft.

  1. C173604
    Install a new seal ring to the output shaft spacer.

  1. C173622
    Align the pin with the straight pin groove of the output shaft spacer, and slide on the output shaft spacer.

  1. C173624
    Using a screwdriver and hammer, tap on the snap ring.


8. INSTALL TRANSFER OUTPUT SHAFT WASHER

  1. C173600
    Install the 2 output shaft washers to the output shaft.


9. INSTALL TRANSFER INPUT SHAFT PLUG

  1. C173497E01
    Using SST and a hammer, tap in a new input shaft plug until its surface is 1.0 to 1.8 mm (0.0394 to 0.0709 in.) from the input shaft upper surface.
    SST
    09950-60010   (09951-00410)
    09950-70010   (09951-07150)

    NOTICE:
    Be careful not to damage or deform the input shaft plug when tapping it.


10. INSTALL TRANSFER INPUT SHAFT BIMETAL FORMED BUSH

  1. C173632E01
    Using SST and a hammer, tap in a new bush until its surface is 5.5 to 5.9 mm (0.217 to 0.232 in.) from the input shaft upper surface.
    SST
    09950-70010   (09951-07150)
    09950-60010   (09951-00610)

    NOTICE:
    Be careful not to damage the input shaft.


11. INSTALL TRANSFER INPUT SHAFT BEARING

  1. C173499E01
    Install the low planetary gear bearing and low planetary gear to the input shaft.

    NOTICE:
    1. Make sure the low planetary gear bearing is installed in the correct direction.
    2. Install the low planetary gear bearing so that its temper color side faces the low planetary gear.

  1. C173498E01
    Install the low planetary gear bearing and a new input shaft bearing to the input shaft.

    NOTICE:
    1. Make sure the input shaft bearing is installed in the correct direction.
    2. Make sure the low planetary gear bearing is installed in the correct direction.
    3. Install the low planetary gear bearing so that its temper color side faces the low planetary gear.

  1. C173500E01
    Using SST and a press, press in the bearing.
    SST
    09513-36040  
    09515-21010  

    NOTICE:
    After press-fitting the bearing to the input shaft, check that the bearing moves smoothly.

  1. C173626
    Select a snap ring that allows for minimum axial play and install it to the shaft.

    Standard Snap Ring Thickness:
    Mark
    Specified Condition
    C
    2.13 to 2.18 mm (0.0839 to 0.0858 in.)
    D
    2.18 to 2.23 mm (0.0858 to 0.0878 in.)
    E
    2.23 to 2.28 mm (0.0878 to 0.0898 in.)
    F
    2.28 to 2.33 mm (0.0898 to 0.0917 in.)
    G
    2.33 to 2.38 mm (0.0917 to 0.0937 in.)
    H
    2.38 to 2.43 mm (0.0937 to 0.0957 in.)
    J
    2.43 to 2.48 mm (0.0957 to 0.0976 in.)

  1. Using a snap ring expander, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.


12. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING

C173492E01
  1. Apply transfer oil to a new seal ring.

  1. Install a new seal ring to the input shaft.


13. INSTALL TRANSFER DRIVEN SPROCKET BEARING

  1. C162208
    Install a new bearing to the front transfer case in the direction shown in the illustration.

    NOTICE:
    Make sure the bearing is installed in the correct direction.

  1. C173489
    Using a screwdriver, install the snap ring.


14. INSTALL TRANSFER LOW PLANETARY RING GEAR

  1. C174065
    Using a snap ring expander, install the snap ring to the front transfer case.

  1. C173496E01
    Install the low planetary ring gear to the front transfer case.

    NOTICE:
    Make sure to install the low planetary ring gear in the correct direction.

  1. C173488
    Using a screwdriver, install the snap ring.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.


15. INSTALL INPUT SHAFT ASSEMBLY

  1. C176062
    While expanding the snap ring, install the input shaft to the front transfer case.

  1. Apply adhesive to the threads of the 2 case plugs.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the plugs within 3 minutes of application.

  1. C159719
    Using a 14 mm hexagon wrench, install the 2 case plugs.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


16. INSTALL TRANSFER CASE MAGNET

  1. C174062
    Install the magnet to the oil separator.


17. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY
  1. Install a new O-ring to the oil separator.

  1. C173486
    Install the oil separator with the 3 bolts.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }


18. INSTALL SIDE GEAR SHAFT HOLDER BEARING

  1. C176193E01
    Using SST and a hammer, tap in a new bearing to the rear transfer case.
    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)

  1. C160519
    Using a screwdriver, install the snap ring.


19. INSTALL FRONT DRIVE CLUTCH SLEEVE

C174060E01
  1. Apply gear oil to the connecting areas of the clutch sleeve and center differential case.

  1. Install the clutch sleeve onto the output shaft.

    NOTICE:
    Make sure that the clutch sleeve is installed facing the correct direction.


20. INSTALL REAR TRANSFER OUTPUT SHAFT ASSEMBLY

  1. C174066
    Install the snap ring to the rear transfer case.

  1. C175996E01
    Install the output shaft, drive chain and driven sprocket.

    NOTICE:
    Do not drop the output shaft washers.

  1. C173484
    Using a snap ring expander, install the snap ring to the output shaft.

    NOTICE:
    Make sure that the snap ring is firmly installed to the groove.


21. INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY

  1. C160356E02
    Install a new O-ring to the shift actuator.

  1. C241090E01
    Set the No. 1 gear shift fork to the front drive clutch sleeve.

  1. C173374
    Install the shift actuator to the rear transfer case with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. C173373
    Install the No. 1 gear shift fork to the shift actuator with the bolt.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }


22. INSTALL NO. 2 TRANSFER GEAR SHIFT FORK

  1. C174533E01
    Set the No. 2 gear shift fork together with the high and low clutch sleeve to the shift actuator.

  1. C173339
    Install the No. 2 gear shift fork to the shift actuator with the bolt.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }

  1. C175998
    Using a screwdriver and hammer, tap the 4 shift fork shaft snap rings onto the shift fork shaft.


23. INSTALL FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING

  1. C173595E01
    Install the needle roller bearing and spacer to the output shaft.


24. INSTALL NO. 1 SYNCHRONIZER RING (for Manual Transmission)

C173623
  1. Align the protrusion of the synchronizer ring with the notch on the differential case and install it.


25. INSTALL REAR TRANSFER CASE ASSEMBLY

  1. C173596E01
    Apply seal packing to the rear transfer case as shown in the illustration.

    Seal Packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    NOTICE:
    If the removed rear transfer case will be reused: After removing the rear transfer case, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear transfer case contact surface, 2) clean off any remaining old FIPG from the rear transfer case contact surface, and 3) reapply seal packing to the rear transfer case.

  1. C173337
    Install the rear transfer case with the 14 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Tighten the bolts within 10 minutes of applying the seal packing. The seal packing will dry very quickly.


26. INSTALL TRANSFER CASE PLUG
  1. Apply adhesive to the threads of the plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the plug within 3 minutes of application.

  1. C173336
    Using a 6 mm hexagon wrench, install the plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }


27. INSTALL NO. 1 TRANSFER CASE PLUG

  1. C176791
    Install the pin and compression spring to the front transfer case.

  1. Apply adhesive to the threads of the plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the plug within 3 minutes of application.

  1. Install the plug.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }


28. INSTALL TRANSFER CASE REAR OIL SEAL
  1. Apply transfer oil to the spline of the output shaft.

  1. C172374E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the housing upper surface.
    SST
    09649-17010  
    09950-70010   (09951-07150)


29. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the companion flange onto the output shaft.

  1. C173334E01
    Using SST to hold the companion flange, install a new O-ring and a new companion flange lock nut.
    SST
    09330-00021  

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }

  1. C174574E01
    Using a chisel and hammer, stake the companion flange lock nut.


30. INSTALL TRANSFER CASE FRONT OIL SEAL
  1. Apply transfer oil to the spline of the driven sprocket.

  1. C172370E02
    Using SST and a hammer, tap in a new oil seal until its surface is 1 to 1.5 mm (0.0394 to 0.0590 in.) from the case upper surface.
    SST
    09649-17010  
    09950-70010   (09951-07150)


31. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the companion flange onto the drive sprocket.

  1. C173331E01
    Using SST to hold the companion flange, install a new O-ring and a new companion flange lock nut.
    SST
    09330-00021  

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }

  1. C174574E01
    Using a chisel and hammer, stake the companion flange lock nut.


32. INSTALL TRANSFER OIL PUMP PLATE OIL SEAL

  1. C173597E01
    Using SST and a hammer, tap in a new oil seal until its surface is flush with the oil pump plate upper surface.
    SST
    09950-60020   (09951-00680)
    09950-70010   (09951-07100)

    NOTICE:
    Be careful not to damage the oil pump plate.


33. INSTALL TRANSFER CASE PLUG

  1. C177450
    Install the relief valve seat, ball and compression spring to the oil pump plate.

  1. Apply adhesive to the threads of the plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the plug within 3 minutes of application.

  1. Using a 10 mm hexagon wrench, install the plug.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }


34. INSTALL TRANSFER CASE STRAIGHT PIN

  1. C162213E01
    Install the 2 straight pins to the input shaft.


35. INSTALL TRANSFER OIL PUMP PLATE
  1. Apply transfer oil to a new O-ring, drive rotor, driven rotor and a new transfer oil seal ring.

  1. C173598E01
    Install the drive rotor to the input shaft.

  1. C173490
    Install the transfer oil seal ring to the input shaft.

  1. Install the O-ring to the oil pump plate.

  1. C159613
    Install the oil pump plate and driven rotor to the front transfer case with the 4 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 9 ft.*lbf }


36. INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY

  1. C174577
    Install the bracket to the rear transfer case with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

← INSPECTION (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →