SERVICE DATA
Specifications · Vehicles built Sep 2011 – Dec 2011
- MAF meter:
Tester Connection
Condition
Specified Condition
4 (THA) - 5 (E2)
-20°C (-4°F)
12.5 to 16.9 kΩ
20°C (68°F)
2.19 to 2.67 kΩ
60°C (140°F)
0.50 to 0.68 kΩ
- Camshaft timing oil control valve:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
6.9 to 7.9 Ω
- VVT sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
835 to 1400 Ω
Hot
1060 to 1645 Ω
- Crankshaft position sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Cold
1630 to 2740 Ω
Hot
2065 to 3225 Ω
- Engine coolant temperature sensor:
Tester Connection
Condition
Specified Condition
1 - 2
Approx. 20°C (68°F)
2.32 to 2.59 kΩ
Approx. 80°C (176°F)
0.310 to 0.326 kΩ
- Throttle body:
Tester Connection
Condition
Specified Condition
1 (M-) - 2 (M+)
20°C (68°F)
0.3 to 100 Ω
- Knock sensor:
Tester Connection
Condition
Specified Condition
1 - 2
20°C (68°F)
120 to 280 kΩ
- Integration relay (IG2):
Tester Connection
Condition
Specified Condition
IG2 MAIN fuse
Always
Below 1 Ω
1C-1 - 1B-8
Battery voltage is not applied to terminals 1B-6 and 1B-7
10 kΩ or higher
Battery voltage is applied to terminals 1B- 6 and 1B-7
Below 1 Ω
- Integration relay (EFI):
Tester Connection
Condition
Specified Condition
EFI main fuse
Always
Below 1 Ω
1C-1 - 1B-4
Battery voltage is not applied to terminals 1B-2 and 1B-3)
10 kΩ or higher
Battery voltage is applied to terminals 1B- 2 and 1B-3)
Below 1 Ω
- Accelerator pedal:
Tester display
Accelerator pedal released
Accelerator pedal depressed
Accelerator position No. 1
0.5 to 1.1 V
2.6 to 4.5 V
Accelerator position No. 2
1.2 to 2.0 V
3.4 to 5.0 V
- Circuit opening relay (C/OPN):
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω
- Air fuel ration sensor (for Bank 1 sensor 1):
Tester Connection
Condition
Specified Condition
1 (HT1A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
- Air fuel ration sensor (for Bank 2 sensor 1):
Tester Connection
Condition
Specified Condition
1 (HT2A) - 2 (+B)
20°C (68°F)
1.8 to 3.4 Ω
- Heated oxygen sensor (for Bank 1 sensor 2):
Tester Connection
Condition
Specified Condition
1 (HT1B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
- Heated oxygen sensor (for Bank 2 sensor 2):
Tester Connection
Condition
Specified Condition
1 (HT2B) - 2 (+B)
20°C (68°F)
11 to 16 Ω
- A/F sensor heater relay:
Tester Connection
Condition
Specified Condition
A/F fuse
Always
Below 1 Ω
1C-1 - 1A-4
Battery voltage is not applied to terminals 1A-2 and 1A-3
10 kΩ or higher
Battery voltage is applied to terminals 1A- 2 and 1A-3
Below 1 Ω
- EFI No. 2 relay:
Tester Connection
Condition
Specified Condition
3 - 5
Battery voltage is not applied to terminals 1 and 2
10 kΩ or higher
Battery voltage is applied to terminals 1 and 2
Below 1 Ω
- Main body ECU:
Tester Connection
Condition
Specified Condition
2A-1 - 2B-17
Battery voltage is not applied to terminals 2B-5 and 2D-43
10 kΩ or higher
Battery voltage is applied to terminals 2B-5 and 2D-43
Below 1 Ω
- Spark plug:
Recommended spark plug
Correct electrode gap for new spark plug
Maximum electrode gap for used spark plug
Standard insulation resistance
DENSO made: SK20R11
Correct electrode gap for new spark plug 1.0 to 1.1 mm (0.0394 to 0.0433in.)
1.3 mm (0.0512 in.)
10 MΩ or higher
NGK made: IFR6A11