2011-2013 Land Cruiser · Service Manual General

TORQUE SPECIFICATIONS

Specifications · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAMSHAFT 
Part Tightened
N*m
kgf*cm
ft.*lbf
Camshaft timing gear x Camshaft
100
1020
74
Camshaft timing exhaust gear x Camshaft
100
1020
74
No. 3 chain tensioner x Camshaft housing LH
21
214
15
Camshaft bearing cap (for Bank 1) x Cylinder head LH
for bolt A
28
286
21
for bolt B
16
163
12
No. 2 chain tensioner x Camshaft housing RH
21
214
15
Camshaft bearing cap (for Bank 2) x Cylinder head RH
for bolt A
28
286
21
for bolt B
16
163
12
No. 1 chain tensioner x Cylinder head RH
10
102
7
Timing chain cover plate x Timing chain cover
9.0
92
80 in.*lbf
CYLINDER HEAD 
Part Tightened
N*m
kgf*cm
ft.*lbf
Cylinder head x Cylinder block
1st
36
367
27
2nd
Turn 90°
3rd
Turn 90°
Cylinder head LH x Cylinder block (for cylinder head set bolt)
1st
36
367
27
2nd
Turn 90°
3rd
Turn 90°
Cylinder head LH x Cylinder block (except cylinder head set bolt)
30
306
22
ENGINE ASSEMBLY 
Part Tightened
N*m
kgf*cm
ft.*lbf
Engine hanger x Cylinder head
33
337
24
Front No. 2 engine mounting bracket LH x Body
32
326
24
Front engine mounting insulator LH x Front No. 1 engine mount bracket LH and Body
for bolt
79
806
58
for nut
72
734
53
Front engine mounting insulator RH x Front No. 1 engine mount bracket RH and Body
for bolt
79
806
58
for nut
72
734
53
Drive plate and ring gear x Crankshaft
83
846
61
Flywheel x Crankshaft
83
846
61
Rear No. 1 engine mounting insulator x Transmission
59
602
44
w/ Winch:
Winch ground wire x Body and Cylinder block
19
196
14
Ground wire x Body
8.4
86
74 in.*lbf
Engine wire x Positive (+) battery cable
7.5
76
66 in.*lbf
Engine wire x Engine room junction block
7.5
76
66 in.*lbf
Ground wire x Bracket
5.0
51
44 in.*lbf
Air cleaner case x Body
5.0
51
44 in.*lbf
Air cleaner cap and hose x Bracket and Throttle body
for bracket
5.0
51
44 in.*lbf
for throttle body
2.5
25
22
No. 2 engine under cover x Body
29
296
21
Hood x Hood bracket
18
178
13
ENGINE UNIT 
Part Tightened
N*m
kgf*cm
ft.*lbf
Stud bolt x Oil pan
for stud bolt A
10
102
7
for stud bolt B and C
4.0
41
35 in.*lbf
Stud bolt x Cylinder head cover
4.0
41
35 in.*lbf
Taper screw plug x Cylinder block
30
306
22
Oil seal retainer x Cylinder block
10
102
7
No. 1 chain vibration damper x Cylinder head LH and Cylinder block
23
229
17
No. 1 idle gear shaft x Cylinder block
60
612
44
Engine water pump x Timing chain cover
11
112
8
No. 1 oil pan baffle plate x Oil pan
10
102
7
Oil pan drain plug x No. 2 oil pan
40
408
30
Cylinder head cover x Camshaft housing RH
for bolt A and D
10
102
7
for bolt B and C
21
214
15
Cylinder head cover LH x Camshaft housing LH
for bolt A and D
10
102
7
for bolt B and C
21
214
15
Rear water by-pass joint x Cylinder head
10
102
7
Oil filler cap housing x Cylinder head cover LH
10
102
7
Cylinder block water drain cock x Cylinder block
30
306
22
Cylinder block water drain cock plug x Cylinder block water drain cock
13
130
9
Front No. 1 engine mounting bracket RH x Cylinder block
43
438
32
Front No. 1 engine mounting bracket LH x Cylinder block
43
438
32
Fuel pipe x Cylinder head cover LH
9.0
92
80 in.*lbf
Heater water hose x Cylinder head cover
18
184
13
CYLINDER HEAD 
Part Tightened
N*m
kgf*cm
ft.*lbf
Stud bolt x Cylinder head
for bolt A
10
102
7
for bolt B
4.0
41
35 in.*lbf
No. 2 straight screw plug x Cylinder head
80
816
59
No. 1 straight screw plug x Cylinder head
44
449
32
CYLINDER BLOCK 
Part Tightened
N*m
kgf*cm
ft.*lbf
Stud bolt x Cylinder block
for stud bolt A and C
10
102
7
for stud bolt B and D
4.0
41
35 in.*lbf
No. 1 oil nozzle x Cylinder block
9.0
92
80 in.*lbf
Crankshaft bearing cap x Cylinder block
Quantity: 16
1st
61
622
45
2nd
Turn 90°
Crankshaft bearing cap x Cylinder block
Quantity: 8
26
262
19
Connecting rod cap x Connecting rod
1st
25
250
18
2nd
Turn 90°
← TORQUE SPECIFICATIONS (Sep 2011 – Dec 2011)SERVICE DATA (from Jan 2012) →