SERVICE DATA
Specifications · Vehicles built Sep 2011 – Dec 2011
| Starter assembly for 1.4 kW Type |
No-load characteristics current |
90 A or less at 11.5 V |
||
| Starter armature assembly |
Standard resistance |
Commutator |
Below 1 Ω |
|
| Commutator - Armature core |
10 kΩ or higher |
|||
| Starter armature assembly |
Standard diameter |
30.0 mm (1.18 in.) |
||
| Minimum diameter |
29.0 mm (1.14 in.) |
|||
| Standard undercut depth |
0.6 mm (0.0236 in.) |
|||
| Minimum undercut depth |
0.2 mm (0.00787 in.) |
|||
| Maximum circle runout |
0.05 mm (0.00197 in.) |
|||
| Brush length |
Standard brush length |
15.5 mm (0.610 in.) |
||
| Minimum brush length |
8.5 mm (0.335 in.) |
|||
| Starter brush holder assembly |
Standard resistance |
Positive brush holder - Negative brush holder |
10 kΩ or higher |
|
| Standard spring installed load |
18 to 24 N (1.8 to 2.4 kgf, 4.0 to 5.3 lbf) |
|||
| Minimum spring installed load |
12 N (1 kgf, 2.7 lbf) |
|||
| Starter yoke assembly |
Standard resistance |
Terminal C wire - Brushes |
Below 1 Ω |
|
| Brushes - Starter yoke body |
10 kΩ or higher |
|||
| Magnet starter switch assembly |
Standard resistance |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Switch body |
Below 2 Ω |
|||
| Starter assembly for 2.0 kW type |
No-load characteristics current |
100 A or less at 11.5 V |
||
| Starter armature assembly |
Standard resistance |
Commutator |
Below 1 Ω |
|
| Commutator - Armature core |
10 kΩ or higher |
|||
| Starter armature assembly |
Standard diameter |
35.0 mm (1.38 in.) |
||
| Minimum diameter |
34.0 mm (1.34 in.) |
|||
| Standard undercut depth |
0.7 mm (0.0276 in.) |
|||
| Minimum undercut depth |
0.2 mm (0.00787 in.) |
|||
| Maximum circle runout |
0.05 mm (0.00197 in.) |
|||
| Brush length |
Standard brush length |
15.0 mm (0.591 in.) |
||
| Minimum brush length |
9.0 mm (0.354 in.) |
|||
| Starter brush holder assembly |
Standard resistance |
Positive brush holder - Negative brush holder |
10 kΩ or higher |
|
| Standard spring installed load |
22 to 28 N (2 to 3 kgf, 4.9 to 6.3 lbf) |
|||
| Minimum spring installed load |
13 N (1 kgf, 2.9 lbf) |
|||
| Starter yoke assembly |
Standard resistance |
Terminal C wire - Brushes |
Below 1 Ω |
|
| Terminal (A) - Terminal (B) |
1.5 to 1.9 Ω at 20°C (68°F) |
|||
| Magnet starter switch assembly |
Standard resistance |
Terminal 50 - Terminal C |
Below 1 Ω |
|
| Terminal 50 - Switch body |
Below 2 Ω |
|||
| Starter relay |
Standard resistance |
3 - 5 |
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2) |
|
| Below 1Ω (Battery voltage is applied to terminals 1 and 2) | ||||
| Starter cut relay |
Standard resistance |
3 - 5 |
10 kΩ or higher (Battery voltage is not applied to terminals 1 and 2) |
|
| Below 1 Ω (Battery voltage is applied to terminals 1 and 2) | ||||
| ACC relay (Main body ECU) |
Standard resistance |
2A-1 - 2D-8 |
10 kΩ or higher (Battery voltage is not applied between 2D-45 and 2D-62) |
|
| Below 1 Ω (Battery voltage is applied between 2D-45 and 2D-62) | ||||
| Engine switch |
Standard resistance |
7 - 5 |
Below 1 Ω (Engine switch is pushed) |
|
| 2 - 5 |
Below 1 Ω (Engine switch is pushed) |
|||
| 7 - 5 |
10 kΩ or higher (Engine switch is not pushed) |
|||
| 2 - 5 |
10 kΩ or higher (Engine switch is not pushed) |
|||