DATA LIST / ACTIVE TEST
System information · Vehicles built from Jan 2012
| READ DATA LIST |
- HINT:
- Using the intelligent tester to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
- NOTICE:
- In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Powertrain / Radar Cruise / Data List.
According to the display on the intelligent tester , read the "Data List".
Radar Cruise Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Accel Request
Accelerator request signal / min.: -2621.44 km/h/s, max.: 2621.36 km/h/s
Actual demanded acceleration request
-
Vehicle Distance
Millimeter wave radar sensor / min.: 0 m (0 ft.), max.: 255 m (836.65 ft.)
Distance to the vehicle in front
-
L/C Option Flag
Dynamic radar cruise option flag / NO or YES
YES: Vehicle-to-vehicle distance control mode is selectable
NO: Vehicle-to-vehicle distance control mode is not selectable
-
Car Dist Time Setting
Vehicle distance time setting condition / SHORT, MID, LONG or NO
Vehicle distance selected by steering pad switch (distance control switch)
-
O/D Cut Request
O/D cut request / Not Request or Request
Not Request: Idling
Request: Performed
-
Shift Down Rqst to 3rd
Shift down request to 3rd gear / Not Request or Request
Not Request: Idling
Request: Performed
-
Shift Down Rqst to 4th
Shift down request to 4th gear / Not Request or Request
Not Request: Idling
Request: Performed
-
Alarm Request
Alarm request signal / Not Request or Request
Request: When beeping
Not Request: When not beeping
-
All Throttle Close Rqst
All throttle close request / Not Request or Request
Request: Requested
Not Request: Not requested
-
Brake Control Request
Brake control request / Not Request or Request
Request: Requested
Not Request: Not requested
-
Targ Decl Slope
Cruise target deceleration slope / 0, 1, 2 or 3
0, 1, 2 or 3
-
CCS Vehicle Spd
Vehicle speed / min.: 0 km/h (0 mph), max.: 255 km/h (159 mph)
Actual vehicle speed displayed
-
CCS Mem Vehicle Spd
Vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)
Actual vehicle speed stored in memory
-
Cruise Operation Status
Transmission range sensor signal / ON or OFF
ON: Shift lever in D (6th, 5th or 4th gear)
OFF: Shift lever not in D (6th, 5th or 4th gear)
-
Cruise Control
Cruise control / ON or OFF
ON: Cruise control operating
OFF: Cruise control not operating
-
CCS Indicator M-CPU
CRUISE main indicator light (Main CPU) / ON or OFF
ON: CRUISE main indicator light on
OFF: CRUISE main indicator light off
-
CCS Ready M-CPU
Cruise control system standby condition (Main CPU) / ON or OFF
ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Main SW M-CPU
Cruise control main switch (Main CPU) / ON or OFF
ON: Cruise control main switch (Main CPU) on
OFF: Cruise control main switch (Main CPU) off
-
Cancel Switch
CANCEL switch / ON or OFF
ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch
-SET switch / ON or OFF
ON: -SET switch on
OFF: -SET switch off
-
RES/ACC Switch
+RES switch / ON or OFF
ON: +RES switch on
OFF: +RES switch off
-
Stop Light SW M-CPU
Stop light switch signal (Main CPU) / ON or OFF
ON: Brake pedal depressed
OFF: Brake pedal released
-
Throttle Opening Angle
Cruise throttle opening angle / min.: 0 deg, max.: 125 deg
Actual demanded throttle angle
-
VSC Fail Safe Flag
Vehicle stability control system fail-safe flag / OFF or ON
ON: Vehicle stability control system fail-safe flag on
OFF: Vehicle stability control system fail-safe flag off
-
Brake Cancel Switch
Brake cancel switch (stop light switch) signal / OFF or ON
ON: Brake pedal depressed
OFF: Brake pedal released
-
Distance Control Switch
Distance control switch signal / ON or OFF
ON: Distance control switch on
OFF: Distance control switch off
-
# Codes
Number of trouble codes / Min.: 0, Max.: 255
-
-
| PERFORM ACTIVE TEST |
- HINT:
- Using the intelligent tester to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: All ECUs / (desired system) / Active Test.
According to the display on the intelligent tester, perform the "Active Test".
Combination Meter Tester Display
Test Part
Control Range
Diagnostic Note
Indicat. Lamp Cruise
Cruise control indicator light
OFF or ON
-
Indicat. Radar Cruise
Radar cruise indicator light
OFF or ON
-
Indicat. SET
Cruise control SET indicator light
OFF or ON
-
ABS/VSC/TRAC Tester Display
Test Part
Control Range
Diagnostic Note
Buzzer
Skid control buzzer sounds
OFF or ON
-