TERMINALS OF ECU
System information · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |


Disconnect the E81 air conditioning amplifier assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E81-21 (+B1) - E81-14 (GND)
R - W-B
Battery power source
Always
11 to 14 V
E81-1 (IG+) - E81-14 (GND)
G - W-B
Ignition power supply
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
E81-14 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.
Reconnect the E81 air conditioning amplifier assembly connector.
Measure the voltage, resistance and waveform according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
E81-8 (LOCK) - E81-35 (SG-5)
L - G
Compressor lock sensor signal
Engine idling
Blower switch LO level
A/C switch on (magnet clutch on)
Pulse generation
(see waveform 1)
E81-35 (SG-5) - Body ground
G - Body ground
Ground for compressor lock sensor signal
Always
Below 1 Ω
E81-13 (SG-2) - Body ground
G - Body ground
Ground for pressure sensor
Always
Below 1 Ω
E81-17 (AC1) - Body ground
L - Body ground
Air conditioning operation request signal
Engine idling
Blower switch LO level
A/C switch off
11 to 14 V
Engine idling
Blower switch LO level
A/C switch on
Below 1 V
E81-27 (ACT) - Body ground
G - Body ground
Magnet clutch operation permission signal
Engine idling
Blower switch LO level
A/C switch off or A/C switch on (magnet clutch off)
11 to 14 V
Engine idling
Blower switch LO level
A/C switch on (magnet clutch on)
Below 1 V
E81-5 (TAM) - E81-13 (SG-2)
V - G
Ambient temperature sensor signal
Ignition switch ON
Ambient temperature 25°C (77°F)
1.6 to 1.8 V
Ignition switch ON
Ambient temperature 50°C (122°F)
0.5 to 0.7 V
E81-30 (S5-1) - E81-13 (SG-2)
LG - G
Power supply for pressure sensor
Ignition switch ON
4.5 to 5.5 V
E81-9 (PRE) - E81-13 (SG-2)
R - G
Air conditioning pressure sensor signal
Engine idling
Blower switch LO level
A/C switch on
0.63 to 4.72 V
Engine idling
Blower switch LO level
A/C switch off
0.63 to 4.72 V
E81-20 (MGC) - E81-14 (GND)
R - W-B
Magnet clutch operation signal
Engine idling
Blower switch LO level
A/C switch on (magnet clutch on permitted)
Below 1 V
Engine idling
Blower switch LO level
A/C switch off or on (magnet clutch on not permitted)
11 to 14 V
E81-23 (BLW) - E81-14 (GND)
R - W-B
Blower motor control signal
Ignition switch ON
Blower switch LO level
Pulse generation
(see waveform 2)
E81-37 (LIN1) - E81-14 (GND)
Y - W-B
LIN communication signal
Ignition switch ON
Pulse generation
E81-25 (ALT) - Body ground
R - Body ground
Generator signal
Engine idling
Pulse generation
E81-3 (PTC1) - Body ground*
W - Body ground
PTC heater relay operation signal
Engine idling
Set temperature MAX. HOT
Engine coolant temperature below 65°C (149°F)
Ambient temperature below 10°C (50°F)
Blower switch off → LO level
Below 1 V → 11 to 14 V
E81-22 (PTC2) - Body ground*
R - Body ground
E81-4 (PTC3) - Body ground*
R - Body ground
z54-4 (B BUS) - z54-2 (BUS G)
-
Power supply for BUS IC
Ignition switch ON
11 to 14 V
z54-5 (SGA) - Body ground
-
Ground for No. 1 cooler thermistor
Always
Below 1 Ω
z54-2 (BUS G) - Body ground
-
Ground for BUS IC
Always
Below 1 Ω
z54-6 (TEA) - z54-5 (SGA)
-
No. 1 cooler thermistor signal
Ignition switch ON
Evaporator temperature 15°C (59°F)
1.4 to 1.8 V
z54-3 (BUS) - z54-2 (BUS G)
-
BUS IC control signal
Ignition switch ON
Pulse generation
- *: w/ PTC Heater
- If the result is not as specified, the air conditioning amplifier assembly may have a malfunction.
- *: w/ PTC Heater
Using an oscilloscope, check waveform 1.

Compressor Lock Sensor Signal Item
Content
Terminal No. (Symbol)
E81-8 (LOCK) - E81-35 (SG-5)
Tool Setting
200 mV/DIV., 10 ms/DIV.
Condition
Engine idling
Blower switch LO level
A/C switch on (magnet clutch on)
- HINT:
- When the rear blower level is increased, the duty ratio changes accordingly.
Using an oscilloscope, check waveform 2.

Blower Motor Control Signal Item
Content
Terminal No. (Symbol)
E81-23 (BLW) - E81-14 (GND)
Tool Setting
1 V/DIV., 500 μs/DIV.
Condition
Ignition switch ON
Blower switch LO level
- HINT:
- When the blower level is increased, the duty ratio changes accordingly.
| CHECK AIR CONDITIONING CONTROL ASSEMBLY |


Disconnect the F10 air conditioning control assembly connector.
Measure the resistance and voltage according to the value(s) in the table below.
Terminal No. (Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
F10-7 (IG+) - F10-1 (GND)
G - W-B
Ignition power supply
Ignition switch ON
11 to 14 V
Ignition switch off
Below 1 V
F10-1 (GND) - Body ground
W-B - Body ground
Ground
Always
Below 1 Ω
- If the result is not as specified, there may be a malfunction on the wire harness side.
- If the result is not as specified, there may be a malfunction on the wire harness side.