2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. INSTALL FRONT DOOR WEATHERSTRIP LH

  1. B180855
    Attach the 21 clips to install the weatherstrip.

    HINT:
    If clips are damaged during installation, replace them.


2. INSTALL FRONT DOOR CHECK ASSEMBLY LH

  1. B180854
    Apply MP grease to the sliding areas of the door check.

  1. Install the door check to the door panel with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the bolt.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }


3. INSTALL FRONT DOOR CHECK COVER LH

  1. B182888
    Install the door check cover.


4. INSTALL FRONT NO. 2 DOOR STIFFENER CUSHION
  1. Clean the installation surface.

    1. Using a heat light, heat the installation surface.

      HINT:
      When installing the door stiffener cushion, heat the vehicle body and door stiffener cushion using a heat light.

      Standard Heating Temperature:
      Item
      Temperature
      Door Stiffener Cushion
      20 to 30°C (68 to 86°F)
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the back door garnish and vehicle body excessively.

    2. Remove the double-sided tape from the installation surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new door stiffener cushion.

    1. Using a heat light, heat a new door stiffener cushion and the installation surface.

      HINT:
      When installing the door stiffener cushion, heat the vehicle body and door stiffener cushion using a heat light.

      Standard Heating Temperature:
      Item
      Temperature
      Door Stiffener Cushion
      20 to 30°C (68 to 86°F)
      Vehicle Body
      40 to 60°C (104 to 140°F)

      NOTICE:
      Do not heat the back door garnish and vehicle body excessively.

    2. Remove the peeling paper from the face of the door stiffener cushion.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. Attach the 2 clamps and double-sided tape to install the door stiffener cushion.

      HINT:
      Press the door stiffener firmly to install it.

    4. B183088
      Install the 2 bolts.


5. INSTALL DOOR ELECTRICAL KEY OSCILLATOR

  1. B183144
    Install the door electrical key oscillator with the screw.


6. INSTALL FRONT DOOR LOCK OPEN ROD LH

  1. B183143
    Install the front door lock open rod as shown in the illustration.


7. INSTALL NO. 2 ELECTRICAL KEY WIRE HARNESS

  1. B180850
    Connect the connector.

  1. Attach the 3 clamps to install the wire harness to the frame.


8. INSTALL FRONT DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B183145
    Attach the 2 claws to install the front door outside handle frame sub-assembly.

  1. B180851
    Using a T30 "TORX" wrench, install the front door outside handle frame sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

    NOTICE:
    A cover should be inserted between the screw and door panel.


9. INSTALL FRONT DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B180847
    Install the front door inside locking cable.

  1. B237389
    Attach the 3 claws.


10. INSTALL FRONT DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B180843
    Install the front door lock remote control cable.


11. INSTALL FRONT DOOR LOCK ASSEMBLY LH

B180842
  1. Apply MP grease to the sliding parts of the front door lock assembly.

  1. Insert the front door lock open rod to the front door lock assembly.

  1. Make sure that the front door lock open rod is securely connected to the front door lock assembly.

  1. Using a T30 "TORX" wrench, install the door lock with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


12. INSTALL FRONT DOOR REAR OUTSIDE HANDLE PAD LH

  1. B180858
    Attach the 2 claws to install the pad.


13. INSTALL FRONT DOOR FRONT OUTSIDE HANDLE PAD LH

  1. B180857
    Attach the 3 claws to install the pad.


14. INSTALL FRONT DOOR HANDLE ASSEMBLY OUTSIDE LH

  1. B182925
    Pull and hold the bellcrank lever of the frame.

  1. Install the handle by pushing it in the direction of the arrow in the illustration.

  1. B180849
    Using a T30 ''TORX'' socket, install the screw.

  1. Connect the connector.


15. INSTALL FRONT DOOR OUTSIDE HANDLE COVER LH

  1. B183142
    Attach the 2 claws to install the front door outside handle cover to the front door lock cylinder.

  1. B180841
    Using a T30 ''TORX'' socket, install the cover (with the door lock cylinder) with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. Install the hole plug.


16. INSTALL FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 ''TORX'' driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new front window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.


17. INSTALL FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B180836E05
    Apply MP grease to the sliding and rotating areas of the window regulator.

    NOTICE:
    Do not apply grease to the spring of the window regulator.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Loosely install the temporary bolt onto the window regulator.

  1. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

    NOTICE:
    Be careful not to drop the window regulator as it may become damaged.

  1. Temporarily install the window regulator with the 5 bolts.

  1. Tighten the 6 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


18. INSTALL FRONT DOOR REAR WINDOW FRAME MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new window frame moulding.

    1. Using a heat light, heat a new window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. B182608E02
      Attach the clip and double-sided tape to install the window frame moulding.

      HINT:
      Press the window frame moulding firmly to install it.


19. INSTALL FRONT DOOR BELT MOULDING SUB-ASSEMBLY LH

B182604
  1. Attach the claw to install the belt moulding.


20. INSTALL LOWER DOOR FRAME GARNISH LH

  1. B180839
    Attach a new clip and install the door frame garnish.


21. INSTALL FRONT DOOR REAR LOWER FRAME SUB-ASSEMBLY LH

  1. B180840
    Install the frame with the bolt.


22. INSTALL FRONT DOOR GLASS RUN LH

  1. B180838
    Install the front door glass run.


23. INSTALL FRONT DOOR GLASS SUB-ASSEMBLY LH

  1. B183141
    Insert the door glass into the door panel along the glass run as indicated by the arrows in the illustration.

    NOTICE:
    Be careful not to damage the glass.

  1. B180832
    Install the door glass to the window regulator with the 2 bolts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


24. INSTALL FRONT INNER DOOR GLASS WEATHERSTRIP LH
  1. Install the front inner door glass weatherstrip LH.


25. INSTALL FRONT DOOR SERVICE HOLE COVER LH

  1. B180831
    Apply butyl tape to the door.

  1. Pass the front door lock remote control cable and front door inside locking cable through a new front door service hole cover.

    NOTICE:
    1. When installing the service hole cover, pull the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. B186231E01
    Connect the 2 connectors.

  1. Attach the 9 clamps.

  1. Install the bolt as shown in the illustration.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


26. INSTALL SIDE AIRBAG SENSOR ASSEMBLY LH

  1. B181765
    Check that the ignition switch is off.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Install the side airbag sensor with the bolt.

    Torque:
    9.0 N*m{ 92 kgf*cm , 80 in.*lbf }

    NOTICE:
    1. If the side airbag sensor has been dropped, or there are any cracks, dents or other defects in the case, bracket or connector, replace it with a new one.
    2. When installing the side airbag sensor, be careful that the SRS wiring does not interfere with other parts and that it is not pinched between other parts.

  1. Check that there is no looseness in the installation parts of the side airbag sensor.

  1. Connect the connector.


27. INSTALL FRONT NO. 1 SPEAKER ASSEMBLY

  1. B181519
    Connect the speaker connector.

  1. Install the speaker with the 4 screws.

    NOTICE:
    Do not touch the cone part of the speaker.


28. INSTALL FRONT DOOR PANEL CUSHION

  1. B180835
    Install the screw and front door panel cushion.


29. INSTALL OUTER MIRROR CONTROL ECU ASSEMBLY (w/ Retract Mirror)

B183140
  1. Connect the 2 connectors.

  1. Install the outer mirror control ECU with the 2 screws.


30. INSTALL OUTER REAR VIEW MIRROR ASSEMBLY LH

B180573E01
  1. Attach the claw and Install the mirror with the 3 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. w/ Power Mirror Control System:

    1. Attach the clamp.

    2. Connect the connector labeled A.


31. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B235655
    Install the front door inside handle bezel to the trim board with the 7 screws.


32. INSTALL FRONT DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B235654
    Attach the 2 claws to install the inside handle.


33. INSTALL SEAT MEMORY SWITCH (w/ Seat Position Memory System)

B180823
  1. Install the seat memory switch the screw.

  1. Connect the connector.


34. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155940
    Connect the connector.

  1. Attach the claw of the courtesy light to the front door trim.


35. INSTALL FRONT DOOR TRIM BOARD SUB-ASSEMBLY LH
  1. Connect the connector.

  1. B183139
    Connect the front door lock remote control cable and front door inside locking cable to the front door inside handle sub-assembly.

  1. B180821
    Attach the 4 claws and 13 clips to install the front door trim board sub-assembly.

  1. Install the 3 screws.


36. INSTALL DOOR ASSIST GRIP COVER LH

  1. B183138
    Attach the 8 claws to install the door assist grip cover to the door trim panel.


37. INSTALL MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY

  1. B182892
    Install the master switch with the 3 screws.


38. INSTALL FRONT DOOR ARMREST BASE PANEL ASSEMBLY LH
  1. Connect the connector.

  1. B183137
    Attach the 5 claws to install the armrest base panel.


39. INSTALL FRONT DOOR INSIDE HANDLE BEZEL LH

  1. B183136
    Attach the 4 claws to install the bezel.


40. INSTALL FRONT LOWER DOOR FRAME BRACKET GARNISH LH

  1. B180820
    Attach the clip and claw, and install the front door lower frame bracket garnish.


41. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


42. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← ADJUSTMENT (from Sep 2011)REASSEMBLY (from Jan 2012) →