2011-2013 Land Cruiser · Service Manual Vehicle Exterior

DISASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

  1. B180907E01
    Using a screwdriver, detach the 4 claws and remove the bezel.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape


3. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  1. B180908
    Using a moulding remover, detach the 7 claws.

  1. Disconnect the connector and remove the armrest base panel.


4. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B180909
    Detach the 2 claws and remove the regulator switch.


5. REMOVE ASSIST GRIP COVER LH

  1. B180910
    Using a moulding remover, detach the 9 claws and remove the door assist grip cover.


6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B180912
    Remove the 3 screws.

  1. Remove the 9 clips, 4 claws and trim board.

  1. Disconnect the connector and remove the trim board.

  1. B180913
    Disconnect the 2 cables from the inside handle.


7. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B235658
    Detach the 2 claws and remove the inside handle.


8. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

  1. B235659
    Remove the 6 screws and rear door inside handle bezel.


9. REMOVE REAR NO. 3 SPEAKER ASSEMBLY (for 14 Speakers)

  1. B181521
    Disconnect the connector.

  1. Detach the clamp.

  1. Remove the 2 screws and speaker.

    NOTICE:
    Do not touch the cone part of the speaker.


10. REMOVE COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155902
    Detach the claw.

  1. Remove the courtesy light and then disconnect the connector.


11. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH

  1. B180917E01
    Remove the weatherstrip by pulling it upward in the direction indicated by the arrow.


12. REMOVE REAR SPEAKER SET (w/ Rear Speaker)

  1. B181520
    Disconnect the speaker connector.

  1. Remove the 3 screws.

  1. Detach the claw and remove the speaker.

    NOTICE:
    Do not touch the cone part of the speaker.


13. REMOVE REAR DOOR SERVICE HOLE COVER LH

  1. B183933E01
    Using a clip remover, detach the 6 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the service hole cover.

    HINT:
    Remove the remaining tape on the door.


14. REMOVE REAR DOOR PANEL PROTECTOR LH

  1. B180911
    Detach the claw and remove the door panel protector.


15. REMOVE REAR DOOR GLASS RUN LH

  1. B180919
    Remove the rear door glass run from the window frame.


16. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

  1. B180920
    Remove the 2 bolts.

  1. Remove the screw and window frame.


17. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  1. B180923
    Remove the rear door quarter window glass and rear door quarter window weatherstrip as a unit as shown in the illustration.


18. REMOVE REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
  1. Remove the quarter window weatherstrip


19. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  1. B180921
    Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


20. REMOVE REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH (for Tempered Glass)

B235660E02
  1. Using a screwdriver with its tip wrapped in protective tape, remove the rear door glass channel.

    Text in Illustration 
    *1
    Protective tape

    NOTICE:
    Be careful not to damage the rear door glass.


21. REMOVE REAR DOOR GLASS CHANNEL FILLER (for Tempered Glass)
  1. Remove the rear door glass channel filler.


22. REMOVE REAR DOOR FRAME GARNISH LH

  1. B180938
    Detach the clip and remove the rear door frame garnish.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.


23. REMOVE REAR NO. 2 DOOR FRAME GARNISH LH

  1. B184224
    Detach the clip and remove the rear door frame garnish.

    HINT:
    This clip needs to be replaced with a new one because the clip will break when removing the rear door frame garnish.


24. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B180924E05
    Loosen the temporary bolt.

    NOTICE:
    Do not remove the temporary bolt. If the temporary bolt is removed, the rear door window regulator may fall and cause damage.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 3 bolts and regulator.

    NOTICE:
    Be careful when removing the bolts as the motor may fall and become damaged.

  1. Remove the temporary bolt from the rear door window regulator sub-assembly.


25. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B294158E01
    Using a T25 "TORX" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.

    Text in Illustration 
    *A
    for Models with Jam Protection Function on 4 Windows
    *B
    for Models with Jam Protection Function on Driver Door Window Only


26. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

B182607E01
  1. Put protective tape around the belt moulding.

  1. B182605
    Detach the claw and remove the belt moulding.


27. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING LH

B182609E01
  1. Put protective tape around the window frame moulding.

  1. Detach the clip and remove the double-sided tape to remove the window frame moulding.


28. REMOVE REAR DOOR LOCK CHILD PROTECTION COVER LH

29. REMOVE REAR DOOR LOCK ASSEMBLY LH

  1. B180926
    Using a T30 ''TORX'' socket, remove the 3 screws and door lock.

    NOTICE:
    Be careful when removing the screws as the door lock may fall and become damaged.


30. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B180928E01
    Using a screwdriver, detach the claw.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape

  1. B180929
    Remove the rear door lock remote control cable.


31. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B180930E01
    Using a screwdriver, detach the 3 claws.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective tape

  1. B188530E02
    Remove the rear door inside locking cable.
    Text in Illustration 
    *A
    except Double Lock
    *B
    w/ Double Lock


32. REMOVE REAR DOOR OUTSIDE HANDLE COVER LH

  1. B185067
    Using a T30 ''TORX'' socket, loosen the screw.

  1. B185061
    Detach the claw and remove the rear door outside handle cover.


33. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B180934
    Using a T30 "TORX" wrench, loosen the screw.

  1. for Entry Function:

    1. Disconnect the connector.

  1. B180933
    Remove the handle by sliding and pulling it in the direction indicated by the arrow in the illustration.


34. REMOVE REAR NO. 1 DOOR OUTSIDE HANDLE PAD LH

  1. B155811
    Detach the 3 claws and remove the pad.


35. REMOVE REAR NO. 2 DOOR OUTSIDE HANDLE PAD LH

  1. B180939
    Detach the 2 claws and remove the pad.


36. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH

  1. B183800
    for Entry Function:

    1. Detach the clamp.

    2. Disconnect the connector.

  1. B155816
    Using a T30 ''TORX'' socket, loosen the screw.

  1. Slide the outside handle frame and No. 4 electrical key wire harness to remove them.

    HINT:
    Remove the outside handle frame through the service hole.

  1. Remove the lock open rod from the outside handle frame.


37. REMOVE NO. 4 ELECTRICAL KEY WIRE HARNESS (for Entry Function)

  1. B184946
    Disconnect the connector.

  1. Detach the 2 clamps, and remove the wire harness from the frame.


38. REMOVE DOOR ELECTRICAL KEY OSCILLATOR (for Entry Function)

  1. B180937
    Remove the screw and door electrical key oscillator.


39. REMOVE REAR DOOR CHECK COVER LH

  1. B180943
    Remove the cover.


40. REMOVE REAR DOOR CHECK ASSEMBLY LH

  1. B155817
    Remove the bolt, 2 nuts and door check.

    HINT:
    Remove the door check through the service hole.

    NOTICE:
    Be careful when removing the bolt and nuts as the door check may fall and become damaged.


41. REMOVE REAR DOOR WEATHERSTRIP LH

  1. B180942
    Detach the 21 clips and remove the rear door weatherstrip.

← COMPONENTS (from Jan 2012)DISASSEMBLY (from Jan 2012) →