2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL REAR DOOR WEATHERSTRIP LH

  1. B180942
    Attach the 21 clips to install the weatherstrip.

    HINT:
    If clips are damaged during installation, replace them.


2. INSTALL REAR DOOR CHECK ASSEMBLY LH
  1. Apply MP grease to the sliding areas of the door check.

  1. B180941
    Install the door check to the door panel with the 2 nuts.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Apply adhesive to the threads of the bolt.

    Adhesive:
    Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

  1. Install the bolt.

    Torque:
    27 N*m{ 275 kgf*cm , 20 ft.*lbf }


3. INSTALL REAR DOOR CHECK COVER LH

  1. B183931
    Install the door check cover.


4. INSTALL DOOR ELECTRICAL KEY OSCILLATOR (for Entry Function)

  1. B180937
    Install the door electrical key oscillator with the screw.


5. INSTALL NO. 4 ELECTRICAL KEY WIRE HARNESS (for Entry Function)

  1. B184946
    Connect the connector.

  1. Attach the 2 clamps to install the wire harness to the frame.


6. INSTALL REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY LH
  1. Apply MP grease to the sliding parts on the rear door outside handle frame sub-assembly.

  1. B183145
    Attach the 2 claws to install the rear door outside handle frame sub-assembly.

  1. B180851
    Using a T30 "TORX" wrench, install the front door outside handle frame sub-assembly with the screw.

    Torque:
    4.0 N*m{ 41 kgf*cm , 35 in.*lbf }

  1. B183800
    for Entry Function:

    1. Attach the clamp.


7. INSTALL REAR NO. 2 DOOR OUTSIDE HANDLE PAD LH

  1. B180939
    Attach the 2 claws to install the rear No. 2 door rear outside handle pad.


8. INSTALL REAR NO. 1 DOOR OUTSIDE HANDLE PAD LH

  1. B155811
    Attach the 3 claws to install the rear No. 1 door outside handle pad.


9. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH

  1. B183930
    Insert the front end of the rear door outside handle assembly into the rear door outside handle frame.

    NOTICE:
    If the bellcrank lever is not pulled and held when installing the outside handle, the bellcrank lever will interfere with the outside handle and the release plate may be damaged

  1. Insert the rear end of the rear door outside handle assembly into the rear door outside handle frame. Next, slide the rear door outside handle assembly toward the front of the vehicle to install it.

  1. B180934
    Using a T30 ''TORX'' socket, tighten the screw.

  1. for Entry Function:

    1. Connect the connector.


10. INSTALL REAR DOOR OUTSIDE HANDLE COVER LH

  1. B185061
    Attach the claw to install the rear door outside handle cover.

  1. B185067
    Using a T30 ''TORX'' socket, install the cover with the screw.


11. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH

  1. B188530E02
    Install the rear door inside locking cable assembly.
    Text in Illustration 
    *A
    except Double Lock
    *B
    w/ Double Lock

  1. B183929
    Attach the 3 claws.


12. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH

  1. B180929
    Install the rear door lock remote control cable assembly.

  1. B183928
    Attach the claw.


13. INSTALL REAR DOOR LOCK ASSEMBLY LH

  1. B183927
    Apply MP grease to the sliding parts of the rear door lock assembly.

  1. Insert the rear door lock assembly to the rear door outside handle release plate, and set it to the rear door panel.

  1. Make sure that the rear door outside handle frame release plate is securely connected to the rear door lock assembly.

  1. Using a T30 ''TORX'' wrench, the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


14. INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH

15. INSTALL REAR DOOR FRONT WINDOW FRAME MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body surface.

    3. Wipe off any tape adhesive residue with cleaner.

  1. Install a new window frame moulding.

    1. Using a heat light, heat a new window frame moulding and the vehicle body surface.

    2. Remove the peeling paper from the face of the window frame moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    3. B182609E02
      Attach the clip and double-sided tape to install the window frame moulding.

      HINT:
      Press the window frame moulding firmly to install it.


16. INSTALL REAR DOOR BELT MOULDING ASSEMBLY LH

B182605
  1. Attach the claw to install the belt moulding.


17. INSTALL REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH
  1. Apply MP grease to the sliding and rotating areas of the regulator motor.

  1. Using a T25 "TORX" driver, install the motor with the 3 screws.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

    HINT:
    A new rear window regulator uses self-tapping screws to thread new installation holes when the self-tapping screws are inserted.


18. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH

  1. B180924E04
    Apply MP grease to the sliding parts of the rear door window regulator sub-assembly.

  1. Loosely install the temporary bolt onto the window regulator.

    Text in Illustration 
    *1
    Temporary Bolt

  1. Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.

    NOTICE:
    Be careful not to drop the window regulator as it may become damaged.

  1. Temporarily install the window regulator with the 3 bolts.

  1. Tighten the 4 bolts in the order shown in the illustration.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }


19. INSTALL REAR NO. 2 DOOR FRAME GARNISH LH

  1. B184224
    Attach a new clip to install the rear door frame garnish.


20. INSTALL REAR DOOR FRAME GARNISH LH

  1. B180938
    Attach a new clip to install the rear door frame garnish.


21. INSTALL REAR DOOR GLASS CHANNEL FILLER (for Tempered Glass)

  1. B235661E01
    Install the rear door glass channel filler onto the rear door glass.
    Text in Illustration 
    *1
    Front side
    *2
    8.0 mm (0.327 in.)


22. INSTALL REAR DOOR GLASS CHANNEL SUB-ASSEMBLY LH (for Tempered Glass)
  1. Apply soapy water to the inside of the rear door glass channel.

  1. B235662E01
    Using a plastic-faced hammer, tap the channel onto the glass to install the glass channel.
    Text in Illustration 
    *1
    Front side
    *2
    8.0 mm (0.327 in.)

    NOTICE:
    Be careful not to damage the glass or glass channel.


23. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH

  1. B180922
    Slide the rear door glass sub-assembly as shown in the illustration to install it.


24. INSTALL REAR DOOR QUARTER WINDOW WEATHERSTRIP LH
  1. Install the rear door quarter window glass to the rear door quarter window weatherstrip.


25. INSTALL REAR DOOR QUARTER WINDOW GLASS LH

  1. B183926
    Install the quarter glass together with the rear door quarter window weatherstrip in the direction indicated by the arrow in the illustration.


26. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

  1. B180920
    Install the rear door rear lower window frame with the 2 bolts and screw.


27. INSTALL REAR DOOR GLASS RUN LH

  1. B180919
    Install the rear door glass run.


28. INSTALL REAR DOOR PANEL PROTECTOR LH

  1. B180911
    Attach the claw to install the door panel protector.


29. INSTALL REAR DOOR SERVICE HOLE COVER LH
  1. Apply butyl tape to the door.

  1. B180918
    Pass the rear door lock remote control cable and rear door inside locking cable through a new rear door service hole cover.

    NOTICE:
    1. When installing the service hole cover, pull the links and connectors through the service hole cover.
    2. There should be no wrinkles or folds after attaching the service hole cover.
    3. After attaching the service hole cover, check the sealing quality.

  1. B183933E02
    Connect the 2 connectors.

  1. Attach the 6 clamps.

  1. B180916E01
    Install the bolt as shown in the illustration.

    Torque:
    8.4 N*m{ 86 kgf*cm , 74 in.*lbf }


30. INSTALL REAR SPEAKER SET (w/ Rear Speaker)

  1. B181520
    Temporarily install the speaker by attaching the claw of the speaker to the door panel.

  1. Install the speaker with the 3 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Connect the connector.


31. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH

  1. B180917E02
    Install the rear inner door glass weatherstrip to the door panel.


32. INSTALL COURTESY LIGHT ASSEMBLY (w/ Courtesy Light)

  1. E155902
    Connect the connector.

  1. Attach the claw of the courtesy light to the rear door trim.


33. INSTALL REAR NO. 3 SPEAKER ASSEMBLY (for 14 Speakers)

  1. B183767E01
    Align the speaker to the door position pins labeled A.

  1. Install the speaker with the 2 screws.

    NOTICE:
    Do not touch the cone part of the speaker.

  1. Attach the clamp and connect the connector.


34. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

  1. B235659
    Install the rear door inside handle bezel to the trim board with the 6 screws.


35. INSTALL REAR DOOR INSIDE HANDLE SUB-ASSEMBLY LH

  1. B235658
    Attach the 2 claws to install the inside handle.


36. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH
  1. Connect the connector.

  1. B183925
    Connect the rear door lock remote control cable and rear door inside locking cable to the rear door inside handle sub-assembly.

  1. B180912
    Attach the 4 claws and 9 clips to install the rear door trim board sub-assembly.

  1. Install the 3 screws.


37. INSTALL ASSIST GRIP COVER LH

  1. B183924
    Attach the 9 claws to install the door assist grip cover to the door trim panel.


38. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY

  1. B180909
    Attach the 2 claws to install the regulator switch.


39. INSTALL REAR DOOR ARMREST BASE PANEL ASSEMBLY LH
  1. Connect the connector.

  1. B183923
    Attach the 7 claws to install the armrest base panel.


40. INSTALL REAR DOOR INSIDE HANDLE BEZEL LH

  1. B183922
    Attach the 4 claws to install the bezel.


41. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

← ADJUSTMENT (from Sep 2011)REASSEMBLY (from Jan 2012) →