2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REPLACEMENT

Removal / installation · Vehicles built from Jan 2012

CAUTION:
  1. Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.
  2. Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners, or solvents.
  3. In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.


1. DRAIN ENGINE OIL
  1. Remove the oil filler cap.

  1. A174194
    Remove the 2 bolts and No. 2 engine under cover seal.

  1. Remove the oil pan drain plug and gasket, and drain the engine oil into a container.

  1. Install a new gasket and the oil pan drain plug.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

  1. Install the No. 2 engine under cover seal with the 2 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


2. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


3. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH

  1. A272726
    Remove the 6 bolts and No. 1 engine under cover sub-assembly LH.


4. REMOVE OIL FILTER ELEMENT

  1. A094910E10
    Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
    Text in Illustration 
    *1
    Pipe
    *2
    Hose

  1. A207196
    Remove the oil filter drain plug.

  1. A272715E01
    Install the pipe to the oil filter cap.
    Text in Illustration 
    *1
    Cap
    *2
    Valve
    *3
    Pipe
    *4
    O-Ring
    *5
    Hose

    NOTICE:
    If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

    HINT:
    Use a container to catch the draining oil.

  1. A207198
    Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring as shown in the illustration.

  1. A207199E02
    Using SST, remove the oil filter cap.
    SST
    09228-06501  
    Text in Illustration 
    *1
    Oil Filter Bracket Clip

    NOTICE:
    Do not remove the oil filter bracket clip.

  1. A209947E02
    Remove the oil filter element and O-ring from the oil filter cap.
    Text in Illustration 
    *1
    Oil Filter Element
    *2
    O-Ring

    NOTICE:
    Be sure to remove the cap O-ring by hand, without using any tools, to prevent damage to the cap O-ring groove.


5. INSTALL OIL FILTER ELEMENT
  1. Clean the inside of the oil filter cap, threads and O-ring groove.

  1. A268595E01
    Apply a light coat of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.
    Text in Illustration 
    *1
    O-Ring
    *a
    CORRECT
    *b
    INCORRECT

    NOTICE:
    1. Be sure to install the O-ring in the proper location, otherwise oil may leak.
    2. Do not twist the O-ring.

  1. Set a new oil filter element to the oil filter cap.

  1. Remove any dirt or foreign matter from the installation surface of the engine.

  1. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    NOTICE:
    1. Do not remove the oil filter bracket clip.
    2. Do not pinch the O-ring for the cap.

  1. A271374E01
    Using SST, tighten the oil filter cap.
    SST
    09228-06501  

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    Text in Illustration 
    *1
    Oil Filter Bracket Clip
    *2
    Oil Filter Cap
    *3
    O-Ring
    *4
    Oil Filter Bracket
    *a
    No Gap

    NOTICE:
    1. When tightening the oil filter cap, do not remove the oil filter bracket clip.
    2. After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

  1. A272716E01
    Apply a small amount of engine oil to a new drain plug O-ring, and install it to the oil filter cap.
    Text in Illustration 
    *1
    O-Ring

    NOTICE:
    Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

  1. Install the oil filter drain plug.

    Torque:
    13 N*m{ 127 kgf*cm , 9 ft.*lbf }

    NOTICE:
    Be careful that the O-ring does not get caught between any surrounding parts.


6. ADD ENGINE OIL
  1. Add fresh oil and install the oil filler cap.

    Standard Oil Grade:
    Oil Grade
    Oil Viscosity (SAE)
    API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil
    0W-20
    5W-20
    5W-30
    10W-30
    API grade SL, SM or SN multigrade engine oil
    15W-40
    20W-50

    Standard Oil Capacity:
    Item
    Specified Condition
    Drain and refill without oil filter change
    7.1 liters (7.5 US qts, 6.2 Imp. qts)
    Drain and refill with oil filter change
    7.5 liters (7.9 US qts, 6.6 Imp. qts)
    Dry fill
    9.3 liters (9.8 US qts, 8.2 Imp. qts)


7. INSPECT ENGINE OIL LEVEL
  1. Warm up the engine, stop the engine and wait 5 minutes. The oil level should be between the dipstick low level mark and full level mark.
    If low, check for leakage and add oil up to the full level mark.

    NOTICE:
    Do not fill engine oil above the full level mark.


8. INSPECT FOR OIL LEAK
  1. Start the engine. Make sure that there are no oil leaks from the area that was worked on.


9. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY LH
  1. Install the No. 1 engine under cover with the 6 bolts.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }


10. INSTALL FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH
  1. Push in the clip to install the front fender splash shield sub-assembly LH.

  1. Install the 3 bolts and screw.

← COMPONENTS (from Jan 2012)COMPONENTS (from Jan 2012) →