2011-2013 Land Cruiser · Service Manual Vehicle Interior

Diagnosis Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC output mode is set by connecting terminals TC and CG of the DLC3.
DTCs are output by the blinking of the SRS warning light.

HINT:
  1. When each warning light stays blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in each ECU is suspected.
  2. A DTC output mode signal is transmitted through the CAN communication system to each ECU including the center airbag sensor. Thus, when all systems do not enter DTC output mode, there may be an ECM malfunction.


WIRING DIAGRAM

C178005E03
C178005E04

INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).


1. CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output (for LHD)
    B
    DTC is output (for RHD)
    C



B
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)

C
REPAIR CIRCUITS INDICATED BY OUTPUT DTCS (Click here)
A


2. CHECK HARNESS AND CONNECTOR (DLC3 - ECM)

  1. C173440E10
    Turn the ignition switch off.

  1. Disconnect the A38 connector from the ECM.

  1. for LHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for 2UZ-FE, 3UR-FE:
      Tester Connection
      Condition
      Specified Condition
      E22-13 (TC) - A38-16 (TC)
      Always
      Below 1 Ω

      for 1GR-FE, 1VD-FTV:
      Tester Connection
      Condition
      Specified Condition
      E22-13 (TC) - A38-27 (TC)
      Always
      Below 1 Ω

  1. for RHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for 2UZ-FE, 3UR-FE:
      Tester Connection
      Condition
      Specified Condition
      E22-13 (TC) - A52-16 (TC)
      Always
      Below 1 Ω

      for 1GR-FE, 1VD-FTV:
      Tester Connection
      Condition
      Specified Condition
      E22-13 (TC) - A52-27 (TC)
      Always
      Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (DLC3 - BODY GROUND)
H102621E11
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E22-4 (CG) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (TC OF ECM - BODY GROUND)
C173441E09
  1. for LHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for 2UZ-FE, 3UR-FE:
      Tester Connection
      Condition
      Specified Condition
      A38-16 (TC) - Body ground
      Always
      1 MΩ or higher

      for 1GR-FE, 1VD-FTV:
      Tester Connection
      Condition
      Specified Condition
      A38-27 (TC) - Body ground
      Always
      1 MΩ or higher

  1. for RHD:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      for 2UZ-FE, 3UR-FE:
      Tester Connection
      Condition
      Specified Condition
      A52-16 (TC) - Body ground
      Always
      1 MΩ or higher

      for 1GR-FE, 1VD-FTV:
      Tester Connection
      Condition
      Specified Condition
      A52-27 (TC) - Body ground
      Always
      1 MΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)


← SRS Warning Light does not Come ON (from Jan 2012)Diagnosis Circuit (from Jan 2012) →