2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedures for the LH side and RH side.
  2. The procedures listed below are for the LH side.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE FRONT LOWER DOOR FRAME BRACKET GARNISH

  1. B180820
    Detach the clip and claw, remove the front lower door frame bracket garnish.


3. REMOVE FRONT DOOR INSIDE HANDLE BEZEL

  1. B180816
    Using a screwdriver, detach the 4 claws and remove the inside handle bezel.

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE FRONT DOOR ARMREST BASE PANEL ASSEMBLY

B180817
  1. Using a moulding remover, detach the 5 claws.

  1. Disconnect the connector and remove the armrest base panel.


5. REMOVE DOOR ASSIST GRIP COVER

  1. B180819
    Using a moulding remover, detach the 8 claws and remove the door assist grip cover.


6. REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

  1. B180821
    Remove the 3 screws.

  1. Remove the 13 clips, 4 claws and trim board.

  1. Disconnect the connector.

  1. B180822
    Disconnect the 2 cables from the inside handle.


7. REMOVE FRONT NO. 1 SPEAKER ASSEMBLY
  1. Disconnect the speaker connector.

  1. B181519
    Remove the 4 screws and speaker.

    NOTICE:
    Do not touch the cone part of the speaker.


8. REMOVE FRONT DOOR SERVICE HOLE COVER

  1. B182874
    Using a clip remover, detach the 9 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the service hole cover.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE FRONT DOOR GLASS SUB-ASSEMBLY
  1. Driver Side:
    Temporarily install the multiplex network master switch.

  1. Passenger Side:
    Temporarily install the power window regulator switch assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Move the door glass until the bolts appear in the service holes.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. B180832
    Remove the 2 bolts.

    NOTICE:
    Be careful when removing the bolts as the glass may fall and become damaged.

  1. B180833
    Remove the door glass in the direction indicated by the arrows in the illustration.

    HINT:
    Remove the glass upward.

    NOTICE:
    Be careful not to damage the glass.

  1. Driver Side:
    Remove the multiplex network master switch.

  1. Passenger Side:
    Remove the power window regulator switch assembly.


10. REMOVE FRONT DOOR WINDOW REGULATOR SUB-ASSEMBLY

  1. B180836E03
    Loosen the temporary bolt.
    Text in Illustration 
    *1
    Temporary Bolt

  1. Remove the 5 bolts, and window regulator.

    HINT:
    Remove the window regulator through the service hole.

    NOTICE:
    Be careful when removing the bolts as the window regulator may fall and become damaged.

  1. Remove the front door window regulator sub-assembly and the front power window regulator motor assembly as a unit.

  1. Remove the temporary bolt from the front door window regulator sub-assembly.


11. REMOVE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY

  1. B294158E01
    Using a T25 "TORX" driver, remove the 3 screws and motor.

    NOTICE:
    Be careful when removing the screws as the motor may fall and become damaged.

    Text in Illustration 
    *A
    for Models with Jam Protection Function on 4 Windows
    *B
    for Front Passenger Side, for Models with Jam Protection Function on Driver Door Window Only

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →